[Elecraft] K3 and N1MM Logger

[Tom Hammond]

David:

At 14:42 12/13/2007, David Wilburn wrote:
>When doing this, are you still able to have paddles connected to the K3
>to send corrections and unexpected information by hand?

YES>.. the K3 has a PADDLE input jack SEPARATE from the KEY (which would
come from the external keying device).

Tom   N0SS


>-
>
>David Wilburn
>k4dgw at k4dgw.com
>K4DGW
>K2 S/N 5982
>
>
>On Thu, 2007-12-13 at 14:03 -0500, Van W1WCG wrote:
> > Paul,
> >
> > The settings you give are identical to what I'm using, however you didn't
> > mention setting the K3 CONFIG parameter PTT--KEY to OFF - dtr.
> > This will match the settings you have in N1MM logger.
> >
> > 73, Van W1WCG
> > K3 #42
> >
> > ----- Original Message -----
> > From: "Paul" <konigsburg at aol.com>
> > To: <Elecraft at mailman.qth.net>
> > Sent: Thursday, December 13, 2007 1:38 PM
> > Subject: [Elecraft] K3 and N1MM Logger
> >
> >
> > >I can get N1MM to see the K3. I am switching logging software, for the
> > > K2 I used WriteLog. The frequency and mode show in the title bar for
> > > N1MM.  However, I can NOT get N1MM  to send CW. to the K3. I see the
> > > software thinking it is sending the CW (the stop light gets bright and
> > > then dims).
> > >
> > > I am using a serial cable connected to the only serial port on the
> > > computer running Windows XP. This same cable and port were able to load
> > > the firmware. For the N1MM configuration I have set Com1 to Elecraft K3,
> > > and the CW/Other box is checked. In the parameters for this port, I have
> > > DTR set to CW and RTS set to Always on. I have tried other combinations
> > > for the DTR and RTS settings and none seem to work. The CW/PTT port
> > > address is 3F8.
> > >
> > > I appreciate guidance from those who have made this work.
> > >
> > > 73,
> > >
> > > :) PK (Paul - K3MZ   K2 #3135  K3 #84)
> > > _______________________________________________
> > > Elecraft mailing list
> > > Post to: Elecraft at mailman.qth.net
> > > You must be a subscriber to post to the list.
> > > Subscriber Info (Addr. Change, sub, unsub etc.):
> > > http://mailman.qth.net/mailman/listinfo/elecraft
> > >
> > > Help: http://mailman.qth.net/subscribers.htm
> > > Elecraft web page: http://www.elecraft.com
> > _______________________________________________
> > Elecraft mailing list
> > Post to: Elecraft at mailman.qth.net
> > You must be a subscriber to post to the list.
> > Subscriber Info (Addr. Change, sub, unsub etc.):
> >  http://mailman.qth.net/mailman/listinfo/elecraft
> >
> > Help: http://mailman.qth.net/subscribers.htm
> > Elecraft web page: http://www.elecraft.com
>
>_______________________________________________
>Elecraft mailing list
>Post to: Elecraft at mailman.qth.net
>You must be a subscriber to post to the list.
>Subscriber Info (Addr. Change, sub, unsub etc.):
>  http://mailman.qth.net/mailman/listinfo/elecraft
>
>Help: http://mailman.qth.net/subscribers.htm
>Elecraft web page: http://www.elecraft.com