[ARC5] Bucking transformer configurations.

Mon Dec 10 10:18:11 EST 2012

This should be required reading on the subject.

http://sound.westhost.com/articles/buck-xfmr.htm#s10

Using that same RS transformer mentioned earlier here is the result of some 
indepth testing a couple of years ago.

-------------------------------------------------------------------

The transformer used was a NOS Radio Shack cat. no, 273-1352, rated for 12.6 
VAC, 1.2 A output, 120 VAC input. It has a center tap, which was ignored for 
the tests. The transformer was made in Taiwan and purchased new about 15-20 
years ago. Except for current rating (and physical size), it is presumably 
similar to the one cited by the OP.

It was decided to load the transformer to approximately 10% of its current 
rating, and approximately 100% to explore its behavior at differing loads. 
Ohmite "Brown Devil" wire-wound resistors were used as loads. Resistances 
were measured with a Rubicon Wheatstone bridge.

A Weston 432 low range wattmeter was used to measure the no-load and 10% 
load wattages. Another Weston 432 with higher ranges was used for the 100% 
load tests. The input voltage was measured with a Sensitive Research model D 
dynamometer voltmeter. The input current was measured with a SR model DYP-2 
dynamometer volt-ammeter. Load current was measured with a Westinghouse PA-5 
ammeter. Load voltage was measured with a Fluke 77 DMM.

In all cases, the input voltage was adjusted as required with an isolated 
variac to 120 volts. In keeping with the OP, only the step-down 
autotransformer and bucking configurations were considered; not the step-up 
or boost connections. "Autotransformer connection" means that the primary 
and secondary are connected in series across the AC line, with the output 
taken from the junction of the primary and secondary, and the other side of 
the AC line. "Bucking" means that the AC line is connected to the primary in 
normal fashion; the load is placed in series with the secondary, and in 
parallel with the primary. With either arrangement, phasing of the windings 
determines whether the load will see a voltage higher or lower than the 
line.

Results:

At 10% and 100% load, the autotransformer connection exhibited slightly 
better power factor and efficiency, but worse voltage regulation than the 
buck-boost connection. With a small power transformer of the type tested, it 
would be better to use the autotransformer connection if maximum efficiency 
is desired, and voltage requirements are only approximate. The bucking 
connection should be used if maintaining a particular voltage difference is 
of prime importance.

[Note: In all cases, the desired output voltage was 120-12.6 = 107.4 V.]

Autotransformer Data:
(At 120 volts input)

At no load, the input current was 0.040 A and the wattage was 2.4 W. This 
yields a VA of 4.8 and a power factor of 50%. The output voltage was 112 V.

At 10% load (830 Ohm resistor), the input was 0.135 A, 15.5 W. This yields a 
VA of 16.2 and a PF of 96%. The output was 108 V, 0.130 A, for an output VA 
of 14.05. The efficiency (VA out / VA in)(100) was 87%. The regulation (V no 
load - V load) / V no load was a 3.57% drop.

At 100% load (88 Ohm resistor), the input was 1.14 A, 133.5 W. The primary 
VA was 136.8 and the PF was 98%. The output was 107.5 V, 1.22 A. The output 
VA was 131.15, giving an efficiency of 98.24%. Regulation was a 4.02% drop.

Buck Transformer Data:
(At 120 volts input)

At no load, the input current was 0.057A, 3.2 W. This gives a VA of 6.84 and 
a PF of 47%. The output voltage was 110.1 V.

At 10% load (830 Ohm resistor), the input current was 0.142 A, 15.2 W. The 
VA was 17.04 and the PF 89%. The output voltage was 109.2 V, and the current 
was 0.132 A. This gives a VA of 14.37. The efficiency was 84%, and 
regulation was 0.82% drop.

At 100% load (88 Ohm resistor), the input current was 1.12 A, 130 W. The 
primary VA was 134.4 and the PF was 97%. The output voltage was 106.7 V, and 
the current was 1.21 A. The output VA was 129.1. Efficiency was 96% and 
regulation was 3.09% drop.

Raw Transformer Data:

DC resistance of primary: 47.73 Ohms. Secondary: 0.65 Ohms.

No load current with secondary disconnected (@ 120 V): 0.056 A, 2.89 W.

Short circuit characteristics: For a secondary current of 1.2 A, an input 
voltage of 18.4 V was required (3.62 watts).

Comment:

The textbook reference cited ("Magnetic Circuits and Transformers") contains 
a chapter on autotransformers which concludes, reading between the lines, 
that there are few general conclusions or formulas that can be derived. Much 
has to do with the specific design and construction of a particular 
transformer. In other words, your mileage may vary!

----- Original Message ----- 
From: "Kenneth G. Gordon" <kgordon2006 at frontier.com>
To: "ARC-5 Mail List" <arc5 at mailman.qth.net>
Sent: Monday, December 10, 2012 2:05 AM
Subject: [ARC5] Bucking transformer configurations.

> For those who may be a bit confused about the correct connections for
> bucking transformers, if you go here:
>
> http://www.w7ekb.com/glowbugs/rx/receivers.htm
>
> and scroll down to 8) Line Voltage Adjustment.
>
> you will find PDF diagrams of both methods, suitable for printing.
>
>
> Kenneth G. Gordon W7EKB
>
> "Courage is being scared to death but saddling up anyway."--- John   Wayne
>
> ______________________________________________________________
> ARC5 mailing list
> Home: http://mailman.qth.net/mailman/listinfo/arc5
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:ARC5 at mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
>
>
> -----
> No virus found in this message.
> Checked by AVG - www.avg.com
> Version: 10.0.1427 / Virus Database: 2634/5447 - Release Date: 12/09/12
> 