[ARC5] Reducing BC-459A chirp: 12A6 replacement for 1626

[Henry Mei'l's]

Dennis -I meant Dennis -- sorry about -- as I told you once,
I had a good friend who worked for Bell Labs with a surname very similar to 
yours - hence the crossover.

Henry

----- Original Message ----- 
From: "Dennis Monticelli" <dennis.monticelli at gmail.com>
To: "Discussion of AN/ARC-5 military radio equipment." 
<arc5 at mailman.qth.net>
Sent: Thursday, July 22, 2010 7:02 PM
Subject: Re: [ARC5] Reducing BC-459A chirp: 12A6 replacement for 1626


> Hi Henry,
>
> I cannot believe that filament voltage rises due to RF pickup other than 
> the
> meter used getting fooled due to the high RF flying around.  Now having 
> said
> that, byapssing of all filament lines with additional caps was commonplace
> to reduce TVI.  Hams did this at the same time they rewired the filament
> circuitry for 12V.  I found that my T-22 (after a minimal reversible mod 
> to
> the output tank) did not generate excessive harmonics at the output and
> I discovered that the cabinet offered sufficient shielding also.  This is 
> in
> contrast to all the articles written in the past about how to deal with 
> TVI
> in ARC-5's by adding all kinds of shielding and tank conversion to PI, 
> etc.
> The major contributor to the TVI problem turned out to be leakage of
> harmonic energy via the key and power lines.  So I filtered all those 
> lines,
> did a final RF sniffer test and all was OK.
>
> Regarding chirp reduction, I didn't understand exactly what WN7RKY was
> talking about from the brief excerpts you provided.  Which tubes were
> involved?  Sounds like a novice ham did a little experimenting and found a
> way in his radio to reduce the chirp by playing with the screen feed.  My
> own tests and experiments led me to conclude there are basically two
> approaches to addressing the chirp.   Either you regulate all supplies
> (starting with the PA screens) or you delay keying the PA until after the
> OSC settles.  The latter can be accomplished either by keying both and 
> then
> using a cap to delay the PA keying relay or you can just run the osc
> continuously during transmit periods.  I actually do all the above :-)
>
> BTW, your tube shipment is all boxed up securely and now I need to get 
> some
> custom declaration paperwork from the post office.
>
> Dennis AE6C
> On Thu, Jul 22, 2010 at 5:02 AM, Henry Mei'l's <meils at get2net.dk> wrote:
>
>> Found this in on page 64 of Hints & Kinks, Vol. 5 (1955)(WN7RKY). Screen
>> grid voltage derives (from osc. anode voltage?) via a 20k series 
>> resistor,
>> bypassed witrh a 0.001uF cap. This is supposed to reduce chirp.
>>
>> (This mod is almost invisible mod and shouldn't cause too much
>> consternation among the purists among us -- and it's easy to retro ;0)
>>
>> Any one tried the this tube switch ?
>>
>> (BTW: On page 40, there is also mention of RF causing 1625 filament
>> voltages to rise to 18-22 volts, cured by grounding to a copper strip
>> running across the chassis and feeding filament voltage via RF-lossy
>> microphone cable with bypass caps at both ends. This is probably old hat;
>> just thought I'd mention it, anyway.)
>>
>> 73
>>
>> Henry OZ1UF, Cph.
>> ______________________________________________________________
>> ARC5 mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/arc5
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:ARC5 at mailman.qth.net
>>
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
>>
> ______________________________________________________________
> ARC5 mailing list
> Home: http://mailman.qth.net/mailman/listinfo/arc5
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:ARC5 at mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html


--------------------------------------------------------------------------------



No virus found in this incoming message.
Checked by AVG - www.avg.com
Version: 9.0.851 / Virus Database: 271.1.1/3021 - Release Date: 07/22/10 
08:36:00