[1000mp] FT-1000MP Typical Maximum Power?

Fri, 28 Dec 2001 14:31:18 -0600

settings 4.0 and 4.3 set the maximum power output.
If you set it to 50 watts, then the rf pwr know has a range of 0 to 50
watts.
The other settings operate similarly.

That's what I do as my amp also only needs 50 watts of drive.
The advantage is...you can't make a mistake.
The disadvantage is...if you operate barefoot...your down half of the
available.

I still go with the 50 watts setting as upping to 100 watts when barefoot is
just barely perceptible most of the time.
Whereas overdriving is ALWAYS  perceptible, especially to nearby stations.
hihi

----- Original Message -----
From: "Dr. Robert C. Smithwick" <[email protected]>
To: <[email protected]>
Sent: Friday, December 28, 2001 11:01 AM
Subject: Re: [1000mp] FT-1000MP Typical Maximum Power?

> Gents
>
> I'm an unabashed, unsophisticated user of my 1000MP.
>
> Is there anything wrong with merely reducing the output as required
> to drive a linear (in my case, an Alpha), by  turning down the output
> control on the front panel?
>
> What am I missing here, except a careful reading of the manual?
> (that too, is about to change, hi).
>
> de/smitty/w6cs
>
>
> >Jeff
> >Way back when, I mean a couple of years ago, I vaguely remember someone
> >saying there was a way to crank the output up.
> >As I wasn't interested I didn't read it to carefully.
> >
> >I'm like you, and have my output set to 50 watts max.
> >
> >
> >----- Original Message -----
> >From: "Jeff Maass" <[email protected]>
> >To: <[email protected]>
> >Sent: Thursday, December 27, 2001 8:46 PM
> >Subject: [1000mp] FT-1000MP Typical Maximum Power?
> >
> >
> >>
> >>  I just swapped in a second FT-1000MP (98-era) that I purchased
> >>  used a few months ago, but which I have never used until now. I
> >>  discovered that it showed 147 watts output on 160 meters, where
> >>  my other (97-era) 'MP maxed out just above the rated 100W!
> >>
> >>  With menu item 4-0 set to '100' watts, the max output is 147 watts.
> >>  With menu item 4-0 set to '50' watts, the max output is 80 watts.
> >>  With menu item 4-0 set to '10' watts, the max output is 14 watts.
> >>
> >>  1) Is there a known problem that this is a symptom of?
> >>
> >>  2) Is there a user adjustment that the previous owner might have
> >>       made to juice the output? (He's out of town, and I'll check with
> >>       him later).
> >>
> >>  My amplifier requires only 50 watts to make legal-limit output, and
> >>  I normally operate my primary 'MP with 4-0 set to '50', so throttling
> >>  back the drive will be natural for me. I'd still like to determine
> >>  whether there is a problem building to a failure!
> >>
> >>  73,
> >>   Jeff Maass       [email protected]     Located near Columbus
Ohio
> >>           USPSA # L-1192       NROI/CRO    Amateur Radio K8ND
> >>      Maass' IPSC Resources Page:  http://home.columbus.rr.com/jmaass
> >>  Circleville USPSA/IPSC:
http://home.columbus.rr.com/jmaass/pcsiipsc.htm
> >>  _______________________________________________
> >>  1000mp mailing list
> >>  [email protected]
> >>  http://mailman.qth.net/mailman/listinfo/1000mp
> >>
> >>
> >
> >_______________________________________________
> >1000mp mailing list
> >[email protected]
> >http://mailman.qth.net/mailman/listinfo/1000mp
>
> _______________________________________________
> 1000mp mailing list
> [email protected]
> http://mailman.qth.net/mailman/listinfo/1000mp
>
>