[Wswss] VHF/UHF Gear For Sale

[T. M.]

K7XC VHF/UHF Gear For Sale - All prices do not include shipping. FOB 89406.
Photos available - Email of call for more details.


222 Mhz Down East Microwave Inc. Transverter Model #222-28
222-28 (222-224 MHz W/28Mhz IF.) Factory Assembled, 25W outout with 10W 
Drive
(Common IF Option), <0.8 dB NF, >17 dB Gain, High level mixer, 13.8 VDC 
nominal,
11 to 16.5 VDC operational. Current drain: 5 -6 amps. Connectors: DC- RCA 
Female,
RF- Type "N", IF- "BNC", PTT- RCA. AUX- RCA.           $350.00 Working Well

AM-6154 - 144 Mhz VHF Amplifier
AM-6154 2M Amplifier, Fully Converted, Built in PTT Circuit with +28V and 
PTT
RCA Female Jack's On Back Panel. Tested at 400+ Watts out with current 8930 
tube.
Runs on either 110V or 220V 60hz AC (Currently configured for 110V), Coaxial 
RF
Relays Not Included.  85 Lbs  shipping weight                  $350.00 
Working Well

AM-494 - 144 Mhz VHF Amplifier
AM-494 2M Amplifier, Fully Converted by Joel - N6AMG (Was part of his 
estate)
Built in Coaxial TR relays, PTT via RCA jack & Pot to adjust Bias/Amplifier
Class on rear panel. Last tested in 1999 at 650+ watts output from the 
current
pair of 4CX250B tubes in class AB1. Runs on either 110V or 220V 60hz AC
(Currently configured for 110V), Operational Status unknown as its been in
storage 11 years. Uses choke input HV filtering for a very stable High 
Voltage.
Used on EME 1993-1998. One of the best built amplifiers I have ever seen.
150 lbs shipping weight 
$400.00 AS IS

222 Mhz Amplifier- Lucas Zeta RF Power Module Model #068074-001, Mil 
Surplus,
Like New Condition. Lucas Zeta RF Power Module Model #068074-001, Specs
Imprinted On case "290-320 MHz. 100W Output. +24V DC Nominal Operating 
Voltage,
+15V DC Enable Bias." RF Lab Measurements: Low Level Swept Testing Centered 
at
222.100 MHz Reveals -27.90 dB Input Return Loss, +16.77 dB Gain, with a
Quiescent Current Of 2.16 Amperes. High Power Testing revealed that 
approximately
5W drive = 150W output @ P1dB. +26V is always present, +15V Bias voltage is
switched on when RF is applied to the amplifier input connector. +28V would
yield even better results. Female SMA Connectors on input and output of 
module.
Serial #17, 26V DC, 5.25W Input = 150W Output @ P1dB. IDQ=2.00A. 12.2A @ 
150W.
Serial #55, 26V DC, 5.25W Input = 150W Output @ P1dB. IDQ=1.95A. 12.2A @ 
150W.
Each unit will also include a brand NEW heatsink/case designed for a solid 
state
amplifier with blank front and rear panels.  Add a simple TR Control circuit 
and
a pair of SMA RF coaxial relays and this is a very clean, self contained, 
100
percent duty cycle, amplifier for 222 Mhz that will last forever. I have two
modules/Heatsink cases available.                     $175 each Working Well

Spare Tubes:
(1) Eimac 8930 (for the AM-6155) Tested, Great condition, Very Low Hours, 
$100
(1) Svetlana (for the AM-6155) Tested/Never used, Brand New Condition, 
$120
(2) Emaic 8874's (For Alpha HF Amps) Untested, Used pulls from ebay, $80 
(pair)
(2) Eimac 4CX250B's (For the AM-494) Untested, Good Condition,       $40 
(pair)

M2 2M9SSb 144 Mhz Yagi.
Gain- 12.0 dBd, Front to back- 24 dBd, Beamwidth- E=35°/H=40°, 50 Ohms "N"
Female, Power Handling- 1500W, Boom length- 14' 6", Number of Elements- 9,
Turning radius, 8', Mast/Mounting- UP TO 2"/H OR V, Wind Area/Survival -
1.2 SQ FT/100 MPH, Weight 6 LBS. Good Condition. 
$100

M2 440-18 432 Mhz Yagi
Frequency range- 420 TO 453 MHz, Gain- 14.5 dBd, Front to back- 23 dB,
Beamwidth- E=27°/H=32°, 50 Ohms "N" Female, Power Handling- 1 KW, Boom
length- 136 Inches, Wind Area/Survival .875 SQ FT/100 MPH Weight 5 lbs.
Good Condition. 
$100

There is more equipment and antennas available and will be posted soon.
If you have any questions please drop me a line. Willing to talk about 
package
deals too.

73s de Tim - K7XC - DM09nm... sk







"One who fears limits his activities. Failure is only the opportunity to 
more intelligently begin again." -Henry Ford