[TMC] Station for sale

[Denis Sharon]

Hello Meir, 

I was prompted to write when I read your post regarding searching for a GPE-1. I have a TMC transmitter that I had previously contemplated selling but resisted. Times have changed. A lot. I’m now just completing construction of a 2000’ sq ft shop  - I restore antique motorcycles - the cost of which has gotten quite out of hand. And cursed with the limit of only 24 hours per day I just haven’t “played radio” for several years. 

So I am once again thinking to sell. It would certainly be preferable to keep the transmitter together. I had spent years searching for particularly clean examples of each unit and it would be a shame to split them up. …but not out of the question. 

You may very well have no interest. But I’m just coming to terms with myself to sell. So if you have any interest or know someone who does, let me know. Be forewarned… I will hate the person who buys this from me. 


Regards, 

Denis Sharon  W1AOK
New Milford, CT 








I don’t presently have photos of the tuning unit nor the TMC stand-alone cabinet for the control unit. 

























> On Jun 10, 2020, at 15:44, Meir WF2U <wf2u at ws19ops.com> wrote:
> 
> Hi Larry, 
> 
> Too bad you're so far...
> First, I've been looking for a GPE AM exciter for several years, with no success. It's a bit awkward to use the SBE-3 multimode exciter on AM. I have the PAL-350/PSP-350 with it, and using a PMO. I also have a couple of VOX-5's, both of which work but have some minor issues; I identified these, I just need to take the time to fix them.
> I can actually trade or sell the PMO or a VOX-5 (after I fix it).
> Recently I found a PAL-1K in Canada, which I really would have liked to have, but that was also for pick-up only.
> 
> Best 73,
> 
> Meir WF2U
> Landrum, SC
> 
> 
> ⁣Sent from BlueMail ​
> 
> On Jun 10, 2020, 3:14 PM, at 3:14 PM, Larry <telegrapher at q.com> wrote:
>> As much as i don't care for the idea, it's time for me to move some of 
>> my gear.  Heavier than normal gear!
>> 
>> I use this stuff on 40M am cause i have a crystal for that band where 
>> the activity, when things are happening anyway.  The Xtal is for 7293 
>> kc.  I have no other method of generating a frequency from a VFO type 
>> piece of gear.  for years i wanted a PMO but i never found one close
>> enough.
>> 
>> TMC PAL-500 uses 4CX350 tubes for 500 W PEP.  I run it at around the 
>> 125W output point on AM.  That's really the only place i use it.
>> 
>> PSP-500 power supply for the PAL-500.  Has original cable and
>> connectors 
>> to interface with the PAL-500.
>> 
>> TMC GPE-2A exciter for driving the PAL-500.  AM, CW, MCW with an output
>> 
>> of about 200 mw.  Tunable from 2 to 32 MC just like the PAL-500.  I
>> also 
>> have extra 4CX350 tubes.  I use a D-104 mic, non-amplified with this 
>> unit and it sounds just fine.  Lots of good audio reports.
>> 
>> Because the power supply is heavy, this stuff should be picked up here 
>> in Arizona.  It's good clean equipment, i take care of my radio stuff.
>> 
>> Questions?    Asking $1200.  I also have manuals for this gear.
>> 
>> I also have a nice clean GPR-90 with the cabinet that i may turn loose 
>> later.  Enjoy listening to it, great looking receiver.
>> 
>> Larry W0OGH
>> 
>> ______________________________________________________________
>> TMC mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/tmc
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:TMC at mailman.qth.net
>> 
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
> ______________________________________________________________
> TMC mailing list
> Home: http://mailman.qth.net/mailman/listinfo/tmc
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:TMC at mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html