[TheForge] titanium underbelly

[terry l. ridder]

Hello

I will not comment nor rant on the wisdom of this project. I take it for
what it is. males playing with very expensive toys.

<begin quote>
Bloodhound gets tough underbelly

A titanium floor will protect the Bloodhound supersonic car from a
maelstrom of grit when it tries to break the land speed record later
this year.

Read more: 
http://www.bbc.co.uk/news/science-environment-32800696

When Andy Green "floors it" in the South African desert later this year,
he expects to be able to break his 18-year-old land speed record.

His British Bloodhound Super-Sonic Car (SSC) is aiming for 800mph
(1,290km/h).

To achieve this extraordinary speed, the RAF man will depend on many
cutting edge technologies and components - not least the actual "floor"
itself.

This piece of titanium panelling will be one of the hardest working
engineering elements on the vehicle.

It has to protect the underside of the car from the blizzard of dust and
grit that will be produced as Bloodhound streaks across the dry lake
surface of Northern Cape's Hakskeen Pan.

One of the strongest primary shockwaves will form right between the
supersonic vehicle's front wheels.

This will turn and churn the dried mud, and, with the help of the
spinning wheels, shotblast Bloodhound's body.

When Andy Green set the existing record of 763mph (1,230km/h) in 1997,
his Thrust machine was badly eroded by the playa it kicked up in its
path. Thrust's aluminium floor was polished to a high-sheen finish and
rubbed wafer thin in places.
The protective belly of the record-breaking Thrust vehicle was badly
eroded in 1997

The new titanium floor just finished at Bloodhound's technical centre in
Bristol hopes to perform much better in even more demanding
circumstances.

"At Swansea University, we set up a test rig where we took the same
material from Hakskeen and fired it at different panels to find the
material that would cope in this high-speed eroding environment - and
that was titanium," explained Conor La Grue, the components chief on the
Bloodhound project.

The new floor was assembled by a team from 71 Squadron, whose normal day
job is to keep the jets of the Royal Air Force in a state fit to fly.
The floor structure runs from the rear chassis to the front wheels
There are more than 4,500 rivets - careful work that will be hidden
under the car

The structure contains about 240 primary parts and has required roughly
1,000 worker hours to put together.

As well as two broad titanium skins, the floor structure incorporates a
multitude of other sections, including ribs, stiffeners, stringers, edge
members, straps, buttstraps, doublers, brackets and cover plates.

And the whole structure is held together by 54 anchor nuts, bolts,
washers and bushes, and 4,547 aerospace grade rivets. These rivets
require immense patience to emplace.

Each rivet hole involves pilot drilling, de-burring, pinning, drilling
out to full diameter, de-burring again, pinning again, counter sinking
and de-burring a final time.

"71 Squadron have been incredible. Their skill of hand is quite extreme,
and they're amazing to watch," observed La Grue.

And yet, all of this exquisite work will essentially be seen by no-one
because it will be hidden under the car. But work, it must.
Bloodhound SSC is moving towards completion at its technical centre in
Bristol

It is quite possible that the shockwave created between the front wheels
will travel ahead of the car, pulverising the desert surface layer
fractions of a second before Bloodhound arrives, creating even more mess
for the floor to deal with.

"There's an interesting premise here that the shock energy will travel
faster through a solid than through air," said La Grue.

"So, potentially, the ground ahead of the car could already be coming
apart before the car gets to it. We won't know that for sure until we
start running, but it would only make the scenario worse because you'd
already have loose material available even before the wheels and the
shockwave pick it up and throw it all over the place."

The assembly of Bloodhound is now reaching a critical phase.

British aerospace companies involved in the project are sending their
components to Bristol for final integration.

The plan is to roll Bloodhound out the door in late summer for a
slow-speed test on the runway of the Newquay Aerohub in Cornwall.

Assuming that goes well, the vehicle will then be shipped to South
Africa to begin its assault on the land speed record.

The intention is to smash that this year before returning to Hakskeen
Pan in 2016 to raise the mark beyond 1,000mph (1,610km/h).
The aim this year is to break the existing record, and then go beyond
1,000mph in 2016
<end   quote>

-- 
terry l. ridder ><>