[TheForge] Fw: forging contest

[David E. Smucker]

Bob,  That a great one, I like that.

It reminds me of machinist training with a German company I use to work 
with.  Young appreciates were given a rough cut piece of hot roll steel and 
required to file a cube to high precision.  The only tools allow were a 
vise, file and try-square.  Had to meet the inspectors requirements or you 
had to keep on filing.  Those with the smallest cube got the lowest grade 
and had to work the longest.

Those machinists were some of the best I ever worked with and really knew 
how to build one-off world class rolling mills.  The company was SMS AG.

Dave

--------------------------------------------------
From: "Bob Willman" <blcksmth at wcnet.org>
Sent: Wednesday, March 04, 2009 12:09 PM
To: "'Blacksmithing List Sponsored by ABANA'" <theforge at mailman.qth.net>
Subject: Re: [TheForge] forging contest

> This is one I used several years ago at our local hammer-in. I
> prepared several pieces of 1" round cut 1.27" (I believe)long. This makes
> each piece 1 cubic inch in volume. The assigned task was to hammer each
> piece into a cube as accurately as possible. The only tools allowed were
> hammer and tongs and a pencil or some other marking device - no other
> measuring devices allowed. My intent with the marking device was that they
> would set the round on end at the corner of the anvil and mark a 1 inch
> square at the corner but no one used it - they just started hammering. I 
> was
> not concerned about being exactly 1" cubed as much as the cube having 
> equal
> sides and square corners.
>
> Be prepared for judging with calipers and a square. To determine the
> winner the final 2 were checked with a square and calipers and it was not 
> an
> easy task to eliminate one of them to second place. As I remember the 
> winner
> was within about .030" from having equal sides and very little out of
> square.
>
> Good luck.
>
>
> Bob Willman
> Bowling Green, Ohio
> The Eagle's Anvil
> WB8NQW
>
> -----Original Message-----
> From: theforge-bounces at mailman.qth.net
> [mailto:theforge-bounces at mailman.qth.net] On Behalf Of dan tull
> Sent: Tuesday, March 03, 2009 11:57 PM
> To: theforge at mailman.qth.net; The_Anvil at yahoogroups.com
> Subject: [TheForge] forging contest
>
> Trying to come up w/ a contest for a conference. Needs to be less than 30
> mins.,and more objective than subjective. All skill levels. Forge welded
> rings, nails, RR spikes, and just plain drawing out for length  have been
> done in the past.  What do you think could be done w/ a min. of special
> tools?
>
>
> dan tull
> Georgia
> ______________________________________________________________
> TheForge mailing list
> Home: http://mailman.qth.net/mailman/listinfo/theforge
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:TheForge at mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
>
>
> ______________________________________________________________
> TheForge mailing list
> Home: http://mailman.qth.net/mailman/listinfo/theforge
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:TheForge at mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
>