[TheForge] Cast Iron Balls..OT

[Peter Hirst]

Heehee.LVQ.

Thank you for sharing

Actually the prototype turned out very nice without the ball.  Probably 
cause its all 7/16 rod instead of tubing, and the legs alone weigh about 3 
lbz.  The finished product, balls and all, will weigh about 8.


----- Original Message ----- 
From: "Washington, Aubrey O." <awashington at ou.edu>
To: <artgawk at thegrid.net>; "Sponsored by ABANA" <theforge at mailman.qth.net>
Sent: Thursday, March 13, 2008 9:28 AM
Subject: RE: [TheForge] Cast Iron Balls..OT


Less Traditional:

"There was a smith, Peter Hirst
Whose lamps, they say, were the worst.
The they tipped and they fell;
Were top-heavy as well,
Till iron balls he found on this list."

Aubrey

________________________________________
From: theforge-bounces at mailman.qth.net [theforge-bounces at mailman.qth.net] On 
Behalf Of Peter Fels And Phoebe Palmer [artgawk at thegrid.net]
Sent: Wednesday, March 12, 2008 9:28 PM
To: Sponsored by ABANA
Subject: Re: [TheForge] Cast Iron Balls..OT

Traditional

" There was a young man from Bombass
   Who had 2 big balls of brass....
   When they clinked together,
   They made stormy weather,
   And lightening shot out of his a$$."

pf

Peter Hirst wrote:
> Looks like just the item.  I may even get a bunch of the smaller ones
> for the finial.
> ----- Original Message ----- From: "Larry Brown" <lp.brown at verizon.net>
> To: "Sponsored by ABANA" <theforge at mailman.qth.net>
> Sent: Wednesday, March 12, 2008 6:09 PM
> Subject: Re: [TheForge] Cast Iron Balls
>
>
>> www.kingmetals.com
>> item 14-3 ductile iron balls 3", 3.77 lbs, about $8 w/o shipping
>> If you have a drill press drill a hole as large as you can in
>> something clamped to the press. sit the ball in it and drill your tap
>> size. This will put you on center. Make sure you get the hole deep
>> enough to have the tap cut the threads you need or get a bottoming tap.
>> Let us know when you make a cannon for the extra balls you order ;-)
>> L Brown
>>
>>
>> At 05:40 PM 3/11/2008 -0400, you wrote:
>>> No joke, I have a project that involves them.  I have been
>>> commissioned to make a line of colonial bridge arm lamps.  I can
>>> fabricate or source all the parts I need excpet one troublesome
>>> little rascal.  It is a cast iron ball about 3" OD, tapped for say
>>> 1/4 20F or 1/4 IP.  I have posted a picture in the album titled "Lamp
>>> Parts" at the photo access site. It serves as a ballast weight at the
>>> base of the lamp No electrical funstion, no structural finction, just
>>> dead weight to lower center of gravity and add stabilioty.   Any
>>> ideas on a source for a source?
>>>
>>> Keziah
>>
>> _______________________________________________
>> Manage membership or unsubscribe at:
>> http://mailman.qth.net/mailman/listinfo/theforge
>> theforge mail list group photo site is
>> http://www.photoaccess.com
>> Login:  blacksmithblacksmith at hotmail.com
>> password:  anvil
>> ___________
>>
>>
>>
>
> _______________________________________________
> Manage membership or unsubscribe at:
> http://mailman.qth.net/mailman/listinfo/theforge
> theforge mail list group photo site is
> http://www.photoaccess.com
> Login:  blacksmithblacksmith at hotmail.com
> password:  anvil
> ___________
>
>
>
_______________________________________________
Manage membership or unsubscribe at:
http://mailman.qth.net/mailman/listinfo/theforge
theforge mail list group photo site is
http://www.photoaccess.com
Login:  blacksmithblacksmith at hotmail.com
password:  anvil
___________
_______________________________________________
Manage membership or unsubscribe at:
http://mailman.qth.net/mailman/listinfo/theforge
theforge mail list group photo site is
http://www.photoaccess.com
Login:  blacksmithblacksmith at hotmail.com
password:  anvil
___________