[TheForge] Press ?

[Dan Brewer]

A log splitter is just a hydraulic ram pressing on to a wedge.  The ram is
powered by a pump.  The pump is turned by a motor.  The motor can be
electric or gas.  Northern tool has pumps that are turned by both types of
motors.  Don't buy a log splitter make the tool you want instead of having a
poor solution to you problem.  An air hammer will be less trouble to make
than modifying a log splitter. The only way I would do this is if I had the
log splitter and had no further use of it in its present form. 

Just my 2 cents worth on this thread.
Dan in Auburn 

-----Original Message-----
From: theforge-bounces at mailman.qth.net
[mailto:theforge-bounces at mailman.qth.net] On Behalf Of Daniel Kretchmar
Sent: Saturday, May 27, 2006 9:07 PM
To: Sponsored by ABANA
Subject: [TheForge] Press ?

I saw some bronze/brass? bells at the annual Guild of Metalsmith's 
Conference in Hastings a few years back.  They flaired out beautifully.  I 
asked the maker (the name is gone), and he told me that he had used a log 
splitter with a positive and negative die to flair out the bells.  It 
sounded like a great idea, but one thing has been preventing me from getting

one.

Do they make electric log splitters with any kind of power? I have been 
thinking about getting one for a awhile, but I don't I want a gas powered 
one running in the shop and I haven't seen good ones that are electric.

Dan
www.irontreeworks.com
----- Original Message ----- 
From: "Jerry Frost" <frosty at customcpu.com>
To: "Sponsored by ABANA" <theforge at mailman.qth.net>
Sent: Saturday, May 27, 2006 10:33 PM
Subject: Re: RE: [TheForge] Press ?


> Steve:
>
> I'm not Ralph for which I'm sure we'll both be eternally glad. <grin> 
> Regardless it wouldn't be difficult to mount a reciever to a splitter. The

> typical configuration has the ram driving the log into a wedge. The wedge 
> is typically welded to a flat plate that bolts to the base of the 
> splitter.
>
> All you'd need to do is torch the appropriate sized opening in the base 
> and make a new bolt on plate with the reciever tube. Reinforcing the area 
> torched away as necessary. This will leave you the option of replacing the

> splitting wedge and having a useful log splitter.
>
> The only drawback I can see on the practical side is ram speed. Log 
> splitters move fairly slowly for good reason and a good forging press 
> should close quickly before going to high pressure.
>
> Other than that all it'll take is a little fab work.
>
> Frosty (NKA Ralph) <grin>
> -------------------------------
> If it ain't forged
> it ain't real.
> Wrought iron is.
> The FrostWorks
>
> Meadow Lakes, AK.
>
> http://www.artmetalradio.com/
>
> ----- Original Message ----- 
> From: <steve at sigmatek.com>
>
>
>> Ralph, do you know of any pictures with a reciever hitch setup?
>>
>> Steve
>>
>>
>
> _______________________________________________
> Manage membership or unsubscribe at:
> http://mailman.qth.net/mailman/listinfo/theforge
> theforge mail list group photo site is
> http://www.photoaccess.com
> Login:  blacksmithblacksmith at hotmail.com
> password:  anvil
> ___________
>
>
> 


_______________________________________________
Manage membership or unsubscribe at:
http://mailman.qth.net/mailman/listinfo/theforge
theforge mail list group photo site is
http://www.photoaccess.com
Login:  blacksmithblacksmith at hotmail.com
password:  anvil
___________