[TheForge] Hardy questions

Chris Kilpatrick crimsonkil at lycos.com
Wed Nov 24 12:36:19 EST 2004 

    This rail never saw service, it still has the finishing grinding marks on the rail top.  When I sliced it through, I could see a line about 5/16 below the surface, that went across the face of the of my cut.  It could just be an illusion of the saw;  I have symetrical undulations across the web of this same rail from my saw, so that is a possibility, but the rail head piece is more abrupt; there is an actual line I can see.  Work hardening as I understand it is like heat treating in that it decreases over depth as opposed to a visible, precise, razor fine line.

-Chris K.

----- Original Message -----
From: "David E. Smucker" <davesmucker at hotmail.com>
To: "Sponsored by ABANA" <theforge at mailman.qth.net>
Subject: Re: [TheForge] Hardy questions
Date: Wed, 24 Nov 2004 11:40:27 -0500

> 
> Chris,  Thinking some more about your question about "something welded to 
> top".  Can you see the line on both sides of the rail?  The action of the 
> wheel flange will cause the head of the rail to roll to the inside.  This is 
> especially true on the outside rail from a curve.  Some railroads had or 
> have special equipment to grind this cold working off of the rail from time 
> to time.  This is also why rail would be re-laid (still is) to use the other 
> side of the rail head as the inside or flange side of the rail.  Over it's 
> service life your rail may well have seen service as both the right hand and 
> left hand rail.
> 
> Dave
> ----- Original Message ----- 
> From: "Chris Kilpatrick" <crimsonkil at lycos.com>
> To: "Sponsored by ABANA" <theforge at mailman.qth.net>
> Sent: Wednesday, November 24, 2004 9:40 AM
> Subject: Re: [TheForge] Hardy questions
> 
> 
> My guestimations had it at 128#/yard, so 133# is not out of the question. 
> it is 7+" tall and the foot is 6" wide and the railhead is 2 3/4" wide.
> 
> -Chris K.
> 
> ----- Original Message -----
> From: "David E. Smucker" <davesmucker at hotmail.com>
> To: "Sponsored by ABANA" <theforge at mailman.qth.net>
> Subject: Re: [TheForge] Hardy questions
> Date: Tue, 23 Nov 2004 21:17:13 -0500
> 
> >
> > Most rail is close to 1080 with about 1 % mag.  By the very nature of it's
> > service requirements rail is very good stuff.  It makes great tools --
> > hammers, cutting tools, woodworking tools, almost anything you would make
> > out of a 1060 to a 1095 steel if buying stock new.  Not sure about you
> > comment about the formation at the top of the rail other than work
> > hardening.  How heavy is your section?  Rail is measure in weight per 
> > yard.
> > (not weight per foot)  This is almost always noted on the side of the rail
> > along with the year of manufacture.  I just pick up some scrap rail that 
> > was
> > 85 pounds per yard made in 1928.  This is small rail for normal railroad
> > use -- most main line track being in the range of 133 pounds per yard. 
> > Rail
> > was often re-laid -- moved from mainline service to siding or yard use to
> > get more life out of it.  Some rail is weld repaired when used in areas 
> > like
> > switch frogs but not over longer lengths that I know of.
> >
> > You can use rail for lots of things -- just know that it is high carbon --
> > don't quench it unless you want it very hard.  For things other than tools 
> > I
> > would use mild steel and save my rail road rail for tooling.
> >
> > Dave Smucker
> > ----- Original Message ----- 
> > From: "Chris Kilpatrick" <crimsonkil at lycos.com>
> > To: "SCA Metalsmiths" <ekmetalsmiths at yahoogroups.com>;
> > <theforge at mailman.qth.net>
> > Sent: Tuesday, November 23, 2004 12:10 PM
> > Subject: [TheForge] Hardy questions
> >
> >
> > Hi folks,
> >      Just got a bandsaw for Christmas (early, I know) I have been reducing
> > some railroad rail into hardy sized pieces, have several questions:
> >      First, it appears as if the rail had a 1/4 piece welded to the top of
> > the rail (there is a clear line where this section stops)  Are 
> > appearancess
> > deceiving?
> >      Secondly, I have come up with plans for spring fuller dies as 
> > follows:
> > flatter dies, drawing dies, vee dies, veining dies, various round and 
> > square
> > dies.  I also have come up with bending forks, rivet bottom tools, several
> > small stake anvils.  Any suggestions on what other tooling UI can make 
> > from
> > RR rail?
> >      By the way, I have no power hammer, so all suggestions need to be
> > slanted to hand hammering.
> >
> > thanks in advance,
> >
> > Chris K.
> >
> > It is I who formed the blacksmith,
> > who fans the flame into a fire and
> > fashions a weapon fit for it's work.
> >
> > -- 
> > _______________________________________________
> > Find what you are looking for with the Lycos Yellow Pages
> > http://r.lycos.com/r/yp_emailfooter/http://yellowpages.lycos.com/default.asp?SRC=lycos10
> >
> > _______________________________________________
> > Manage membership or unsubscribe at:
> > http://mailman.qth.net/mailman/listinfo/theforge
> > theforge mail list group photo site is
> > http://www.photoaccess.com
> > Login:  blacksmithblacksmith at hotmail.com
> > password:  anvil
> > ___________
> >
> >
> > _______________________________________________
> > Manage membership or unsubscribe at:
> > http://mailman.qth.net/mailman/listinfo/theforge
> > theforge mail list group photo site is
> > http://www.photoaccess.com
> > Login:  blacksmithblacksmith at hotmail.com
> > password:  anvil
> > ___________
> >
> >
> >
> 
> 
> 
> It is I who formed the blacksmith,
> who fans the flame into a fire and
> fashions a weapon fit for it's work.
> 
> -- 
> _______________________________________________
> Find what you are looking for with the Lycos Yellow Pages
> http://r.lycos.com/r/yp_emailfooter/http://yellowpages.lycos.com/default.asp?SRC=lycos10
> 
> _______________________________________________
> Manage membership or unsubscribe at:
> http://mailman.qth.net/mailman/listinfo/theforge
> theforge mail list group photo site is
> http://www.photoaccess.com
> Login:  blacksmithblacksmith at hotmail.com
> password:  anvil
> ___________
> 
> 
> _______________________________________________
> Manage membership or unsubscribe at:
> http://mailman.qth.net/mailman/listinfo/theforge
> theforge mail list group photo site is
> http://www.photoaccess.com
> Login:  blacksmithblacksmith at hotmail.com
> password:  anvil
> ___________
> 
> 
> 



It is I who formed the blacksmith, 
who fans the flame into a fire and
fashions a weapon fit for it's work.

-- 
_______________________________________________
Find what you are looking for with the Lycos Yellow Pages
http://r.lycos.com/r/yp_emailfooter/http://yellowpages.lycos.com/default.asp?SRC=lycos10

More information about the TheForge mailing list