[TheForge] Re: Plasma cutter comparison

Mon Nov 3 18:54:00 2003

Oh and mine was about $700 USD roughly

----- Original Message -----
From: "R.C.Mundt" <[email protected]>
To: <[email protected]>
Sent: Tuesday, November 04, 2003 7:01 AM
Subject: Re: [TheForge] Re: Plasma cutter comparison


> So Shannell could any knothead buy some components, stick them together
and
> have a cnc torch? Or do you have to have knowledge of computers and such?
> About how much did you spend on your setup?
> Randy Mundt
> ----- Original Message -----
> From: "shannell Sugrue" <[email protected]>
> To: <[email protected]>
> Sent: Monday, November 03, 2003 5:27 AM
> Subject: Re: [TheForge] Re: Plasma cutter comparison
>
>
> > Can be used as an on off switch orin conjuntion with an arc voltage
> feedback
> > loop to control torch height, but you are right, I find though that 3
axis
> > drivers arent much dearer and you have a third axis as a spare for when
> you
> > blow up a component on one of the other axis, just hook up to the extra
> > axis....
> > ----- Original Message -----
> > From: "Harland Johnson" <[email protected]>
> > To: <[email protected]>
> > Sent: Monday, November 03, 2003 9:41 PM
> > Subject: [TheForge] Re: Plasma cutter comparison
> >
> >
> > >
> > >
> > > 3 Axis Drivers?  Isn't that overkill on a plasma torch?  The CNC
plasma
> > that
> > > I used only needed an x-y axis.  I can understand the 3rd axis for
> > something
> > > like  a cnc router.
> > >
> > > Dann Johnson
> > >
> > > shannell Sugrue writes:
> > >
> > > > The net is full of cnc setup help, I built a cnc plasma a while
back,
> > hardly
> > > > use it but was fun building it, got my 3 axis driver from
ampshop.com
> I
> > > > think, rest is basic mechanicals....
> > > > ----- Original Message -----
> > > > From: <[email protected]>
> > > > To: <[email protected]>
> > > > Sent: Saturday, November 01, 2003 2:39 PM
> > > > Subject: Re: [TheForge] Plasma cutter comparison
> > > >
> > > >
> > > >> My friend built one that you can here:
> > > >>
> > > >> http://www.randyray.org/TMC/pictures.htm
> > > >>
> > > >> I recall, that the basic software and stepper motors came from
here,
> > but
> > > >> I may be wrong:
> > > >>
> > > >> http://www.torchmate.com/index.htm
> > > >>
> > > >> at the time, the kits were less than $2000, they have gone up.
> Another
> > > >> supplier is at :* http://www.super-tech.com*
> > > >> I have been looking at doing my own stepper controller and buying
> > > >> TurboCad's CAM package ($500 as an upgrade I think) whenever I bite
> the
> > > >> bullet and buy one.  Given access to Randy's machine, it may be a
> while
> > > >> though.
> > > >>
> > > >> Charles
> > > >>
> > > >>
> > > >>
> > > >> Kenny O. wrote:
> > > >>
> > > >> > Ed F wrote:
> > > >> >
> > > >> >>
> > > >> >> I was looking at the 380 but decided to lay out the extra cash
to
> > have
> > > > a
> > > >> >> machine that would work well on a "home made CNC table" and cut
> > > >> >> thicker stuff with.
> > > >> >>
> > > >> > Did you design this yourself or are there plans available?
> > > >> > Ken o
> > > >> >
> > > >>
> > > >> _______________________________________________
> > > >> http://mailman.qth.net/mailman/listinfo/theforge
> > > >> theforge mail list group photo site is
> > > >> http://www.photoaccess.com
> > > >> Login:  [email protected]
> > > >> password:  anvil
> > > >> ___________
> > > >>
> > > >
> > > > _______________________________________________
> > > > http://mailman.qth.net/mailman/listinfo/theforge
> > > > theforge mail list group photo site is
> > > > http://www.photoaccess.com
> > > > Login:  [email protected]
> > > > password:  anvil
> > > > ___________
> > > >
> > > >
> > >
> > >
> > >
> > > Dann Johnson
> > > _______________________________________________
> > > http://mailman.qth.net/mailman/listinfo/theforge
> > > theforge mail list group photo site is
> > > http://www.photoaccess.com
> > > Login:  [email protected]
> > > password:  anvil
> > > ___________
> > >
> >
> > _______________________________________________
> > http://mailman.qth.net/mailman/listinfo/theforge
> > theforge mail list group photo site is
> > http://www.photoaccess.com
> > Login:  [email protected]
> > password:  anvil
> > ___________
> >
> >
> >
>
> _______________________________________________
> http://mailman.qth.net/mailman/listinfo/theforge
> theforge mail list group photo site is
> http://www.photoaccess.com
> Login:  [email protected]
> password:  anvil
> ___________
>