[SJRA-Members] Yaesu Active Nodes

[John Fogleboch]

Hi Craig,

I haven’t tried to connect to either repeater in over a year via WiresX but in the past it did work with my PDN.  Both repeaters should be connected to WiresX with internet connections but this objective has been walked away from over the years by trying to do it on the cheap.

I have been told the introduction of Echo Link on K2AA has really screwed things up.  Also K2AA has had hardware problems that have plagued it for years and remain unfixed.  I gave up trying to encourage the SJRA Officers and BOD to get serious about fixing these problems.  There is just no interest in C4FM and WiresX within the current administration.  Maybe the new one will get serious and stay with it until finished.  

And our third repeater is still off the air with no visible plan on what to do with it.
 
73,
John WY2J 

Sent from my iPhone

> On Mar 30, 2021, at 6:38 PM, Craig Henning <cchenningnj at yahoo.com> wrote:
> 
> Sorry, should have been “Offline Error”
> 
>> On Mar 30, 2021, at 18:19, Craig Henning
>> 
>> That probably won’t work either, with the two repeaters connected, all I get when I try to connect is “Offline Etror”
>> 
>> Craig, NC2H 
>> 
>>> On Mar 30, 2021, at 13:50, John Fogleboch via SJRA-Members <sjra-members at mailman.qth.net> wrote:
>>> 
>>> Hi Bob,
>>> 
>>> You can’t connect any Hot Spot, including the OpenSpot2 or 3, to Yaesu’s WiresX network, they are not compatible.  Since the SJRA repeaters are not connected to the YSF or FCS networks, that approach won’t work either.  
>>> 
>>> What will work is to setup a Yaesu Portable Digital Node (PDN) which takes a Yaesu compatible transceiver like a FT2D, FT3D, FTM400 or a FTD300, the special Yaesu connection cable, a PC with an internet connection and free Yaesu software.  You will have to register the transceiver you use with Yaesu and receive your node and room ID DTMF codes.  This will allow connection to any WiresX node or room including the SJRA machines.  See the Yaesu web site for details.  My PDN system is down now but Jack WA2HJG has a system that was featured on the cover of Harmonics a few months ago  If you own one of the compatible transceivers and PC, the cable is sold at HRO for about $60, your total new cost.  I hope this helps. 
>>> 
>>> 73, John WY2J 
>>> 
>>> Sent from my iPhone
>>> 
>>>> On Mar 30, 2021, at 11:54 AM, rmatteucci <rmatteucci at gmail.com> wrote:
>>>> 
>>>> I am wondering if I, as a member out of range of the repeater, can use an
>>>> Openspot3 or other mutli-mode node that can connect to C4FM nodes can
>>>> connect and communicate on the K2AA repeater? If so, what would one connect
>>>> to in terms of YSFReflector number or FCS server / room? Thanks,
>>>> Bob N2TEV
>>>> ______________________________________________________________
>>>> SJRA-Members mailing list
>>>> Home: http://mailman.qth.net/mailman/listinfo/sjra-members
>>>> Help: http://mailman.qth.net/mmfaq.htm
>>>> Post: mailto:SJRA-Members at mailman.qth.net
>>>> 
>>>> This list hosted by: http://www.qsl.net
>>>> Please help support this email list: http://www.qsl.net/donate.html
>>> 
>>> ______________________________________________________________
>>> SJRA-Members mailing list
>>> Home: http://mailman.qth.net/mailman/listinfo/sjra-members
>>> Help: http://mailman.qth.net/mmfaq.htm
>>> Post: mailto:SJRA-Members at mailman.qth.net
>>> 
>>> This list hosted by: http://www.qslnet
>>> Please help support this email list: http://www.qsl.net/donate.html