[SixClub] SIX is OPEN!

[K8RI on six]

On 5/31/2011 8:34 PM,  Richard J. Fiero II W5TFW wrote:
> did I authorize this ?
Out of respect I didn't work any of them...course I was out chasing 
tornadoes agin! Thing is I have photos of the shelf cloud, wall clouds, 
and even a roll could. I have one of the wall and shelf cloud and one of 
the wall cloud when it had rotation resized to screen size and ready to 
put up.  Don't think I'll get it done tonight though.  I'll have to get 
an early start though as I have a bunch of meetings the next two days 
and tomorrow is supposed to be really windy and I have an airplane to 
bring home.

Hearing that XE1 S9 sure put a bug ...er desire to that 7L Yagi for six 
back up.  I gota get that 50' 25 G finished for the tribander and 
6-meter Yagi.

Next week "I think" we go done to Warren MI to pick up a Bridgeport 
floor mill for the shop.
All this time and I'm supposed to be retired.  Then I'm going to have to 
build a hoist to put the rotary, indexing table, and milling vise on the 
9 X 46" table. A 12" rotary table weighs about 200# while the vise is 
only about 80#.

Anyone know how to powder coat the inside of 30' long pieces of 2", 2 
1/2", 3", 3 1/2", and 4" structural steel tube? What would be nice would 
be the capability of powder coating a completed 30' section of tower. 
Unfortunately the inner section is 2' on a side, the next is over 2 1/2' 
and the third is about 3' 4" across each face meaning the 4th or bottom 
section is about 4' across each face and this honker is going to take 
about 12 yards of concrete for a base.

I figure each section will be strong enough to support a 3 ton truck.


73

Roger (K8RI)

>
>                                :-)
>
>
>
>
>
>
>
>                                            Richard J. Fiero II
>                                      A.R.S. W5TFW // V44TFW
> ----- Original Message -----
> From: "K8RI on six"<50MHz at rogerhalstead.com>
> To: "World Wide Six Meter Club"<sixclub at mailman.qth.net>
> Sent: Tuesday, May 31, 2011 7:32 PM
> Subject: [SixClub] SIX is OPEN!
>
>
>> Copy XE1FZE S9 at times at times 50.123 00:15Z and still hearing him at
>> 00:30Z. He was working a number of states E of the Mississippi and
>> apparently up to New England.
>>
>> I was hearing lost of gulf coast stations.
>>
>> 73
>>
>> Roger (K8RI)
>>
>> ______________________________________________________________
>> SixClub mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/sixclub
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:SixClub at mailman.qth.net
>>
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
> ______________________________________________________________
> SixClub mailing list
> Home: http://mailman.qth.net/mailman/listinfo/sixclub
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:SixClub at mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
>