[SADXA] Local source for ladder line and toriods?

[Richard Solomon]

OK, now how can I get them to you ?

Also, how many of each do you need ?

73, Dick, W1KSZ

On Fri, Jul 29, 2016 at 10:35 AM, Keith Schlottman, CPA, PFS <
keith at schlottmancpa.com> wrote:

> Dick, I think the 43 mix would be just fine, perhaps even better than 61.
> In fact I'm learning a lot about toroids as part of this project and using
> something different will only help me learn more!
>
> Here's a nice document about different mixes that I found, in case anyone
> else is interested:
>
>
> http://palomar-engineers.com/ferrite-products/ferrite-cores/ferrite-mix-selection
>
>
> On Fri, Jul 29, 2016 at 9:56 AM, Richard Solomon <dickw1ksz at gmail.com>
> wrote:
>
> > I should have mentioned that the ones
> > I have are not the -61 mix. The
> > permiability is different, that may affect
> > the number of turns you wind on them.
> >
> > Some experimenting would be necessary.
> >
> > 73, Dick, W1KSZ
> >
> > On Fri, Jul 29, 2016 at 9:44 AM, Richard Solomon <dickw1ksz at gmail.com>
> > wrote:
> >
> > > I have some FT140-43 toroids (1.4"
> > > od, 43 mix) and some T-50-6 ones.
> > >
> > > Can you use those ?
> > >
> > > 73, Dick, W1KSZ
> > >
> > > On Fri, Jul 29, 2016 at 9:34 AM, Keith Schlottman, CPA, PFS <
> > > keith at schlottmancpa.com> wrote:
> > >
> > >> Dick, I'm looking for the round ring type to wind some wire around to
> > make
> > >> a couple of baluns.  I have several plans in mind but something like
> an
> > >> FT-50-61 (1/2" OD) and FT-140-61 (1.4" OD) would get me started.
> > >>
> > >> On Fri, Jul 29, 2016 at 8:17 AM, Richard Solomon <dickw1ksz at gmail.com
> >
> > >> wrote:
> > >>
> > >> > Good morning ... I have a box full of
> > >> > Toroids; Snap-on types, round, the
> > >> > kind you slip RG-8 thru, etc.
> > >> > What are you looking for ?
> > >> >
> > >> > 73, Dick, W1KSZ
> > >> >
> > >> > On Fri, Jul 29, 2016 at 7:55 AM, Keith Schlottman, CPA, PFS <
> > >> > keith at schlottmancpa.com> wrote:
> > >> >
> > >> > > Are there any local stores that would carry 450 Ohm ladder line
> > and/or
> > >> > > ferrite toroids?
> > >> > >
> > >> > > I did check Elliott's website and don't see either listed.
> > >> > >
> > >> > > Hoping to work on an antenna project this weekend but maybe I'll
> > need
> > >> to
> > >> > > mail order these.
> > >> > >
> > >> > > Thanks and 73,
> > >> > >
> > >> > > Keith KR7RK
> > >> > > ______________________________________________________________
> > >> > > SADXA Website http://www.sadxa.org
> > >> > >
> > >> > > SADXA mailing list
> > >> > > Home: http://mailman.qth.net/mailman/listinfo/sadxa
> > >> > > Help: http://mailman.qth.net/mmfaq.htm
> > >> > > Post: mailto:SADXA at mailman.qth.net
> > >> > >
> > >> > > This list hosted by: http://www.qsl.net
> > >> > > You can support qsl.net: http://www.qsl.net/donate.html
> > >> > >
> > >> > ______________________________________________________________
> > >> > SADXA Website http://www.sadxa.org
> > >> >
> > >> > SADXA mailing list
> > >> > Home: http://mailman.qth.net/mailman/listinfo/sadxa
> > >> > Help: http://mailman.qth.net/mmfaq.htm
> > >> > Post: mailto:SADXA at mailman.qth.net
> > >> >
> > >> > This list hosted by: http://www.qsl.net
> > >> > You can support qsl.net: http://www.qsl.net/donate.html
> > >> >
> > >>
> > >>
> > >>
> > >> --
> > >> ______________________________________________________________
> > >> SADXA Website http://www.sadxa.org
> > >>
> > >> SADXA mailing list
> > >> Home: http://mailman.qth.net/mailman/listinfo/sadxa
> > >> Help: http://mailman.qth.net/mmfaq.htm
> > >> Post: mailto:SADXA at mailman.qth.net
> > >>
> > >> This list hosted by: http://www.qsl.net
> > >> You can support qsl.net: http://www.qsl.net/donate.html
> > >>
> > >
> > >
> > ______________________________________________________________
> > SADXA Website http://www.sadxa.org
> >
> > SADXA mailing list
> > Home: http://mailman.qth.net/mailman/listinfo/sadxa
> > Help: http://mailman.qth.net/mmfaq.htm
> > Post: mailto:SADXA at mailman.qth.net
> >
> > This list hosted by: http://www.qsl.net
> > You can support qsl.net: http://www.qsl.net/donate.html
> >
>
>
>
> --
>
> ---------------------------------------------
>
> Keith Schlottman, CPA
>
> http://www.schlottmancpa.com
>
> keith at schlottmancpa.com
>
> (520) 298-8488
>
> ---------------------------------------------
>
> *********************IMPORTANT INFORMATION************
>
> This communication, including attachments, is
>
> for the exclusive use of addressee and may contain proprietary,
>
> confidential and/or privileged information.  If you are not the intended
>
> recipient, any use, copying, disclosure, dissemination or distribution is
>
> strictly prohibited.  If you are not the intended recipient, please notify
>
> the sender immediately by return e-mail, delete this communication and
>
> destroy all copies.
> *************************************************************************
> ______________________________________________________________
> SADXA Website http://www.sadxa.org
>
> SADXA mailing list
> Home: http://mailman.qth.net/mailman/listinfo/sadxa
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:SADXA at mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> You can support qsl.net: http://www.qsl.net/donate.html
>