[R-390] Setting GAIN ADJ

[Larry Haney]

Hi Barry,  If your 390 is in correct working order then Chuck's short
cut is good to use.  But if you are not positive that it is working
correctly, then use the '55 tech ref method you ref'd.  And, the IF input
is not low impedance, so the sig gen output will need to have a 50 ohm load
on it and the gain adjust must not be at the ends of its adjustment.

Regards, Larry

On Fri, Oct 11, 2024 at 7:49 PM Barry Scott <72volkswagon at gmail.com> wrote:

> Yes, that's the 1955 version that I was referring to where it
> describes using the IF input and a 30% modulated 455kc signal at 150uV
> to produce -7.0V at the Diode Load.  The later paper manual I have
> from 1962 uses the antenna input for this.  Chuck Rippel's method uses
> strictly the noise level and the LINE GAIN meter to set it.  I'm a bit
> confused as to what's the best way.
>
> Thanks,
> Barry - N4BUQ
>
> On Fri, Oct 11, 2024 at 8:56 PM Jim Whartenby via R-390
> <r-390 at mailman.qth.net> wrote:
> >
> > https://bama.edebris.com/download/military/r390/Collins_R390_1953.pdf
> >
> > Logic: Method used to arrive at the wrong conclusion, with confidence.
> Murphy
> >
> >     On Friday, October 11, 2024 at 06:16:31 PM CDT, Barry Scott <
> 72volkswagon at gmail.com> wrote:
> >
> >  Looking at the older (1955) vs newer (1962) manuals for the R-390/URR,
> > the older one describes setting the GAIN ADJ pot using input directly
> > into the IF deck; whereas the newer one describes setting it using the
> > antenna input jack.  Is one method any better or preferred to the
> > other?
> >
> > One of the reasons I'm asking is that when I try the direct input to
> > the IF deck method, I can't get -0,7V on the Diode Load which makes me
> > think I have a gain problem in the IF deck.
> >
> > I know there were several posts about this over the years but I've
> > lost track of those for the most part so I thought I'd ask.
> >
> > Thanks,
> > Barry - N4BUQ
> > ______________________________________________________________
> > R-390 mailing list
> > Home: http://mailman.qth.net/mailman/listinfo/r-390
> > Help: http://mailman.qth.net/mmfaq.htm
> > Post: mailto:R-390 at mailman.qth.net
> >
> > This list hosted by: http://www.qsl.net
> > Please help support this email list: http://www.qsl.net/donate.html
> >
> > ______________________________________________________________
> > R-390 mailing list
> > Home: http://mailman.qth.net/mailman/listinfo/r-390
> > Help: http://mailman.qth.net/mmfaq.htm
> > Post: mailto:R-390 at mailman.qth.net
> >
> > This list hosted by: http://www.qsl.net
> > Please help support this email list: http://www.qsl.net/donate.html
> ______________________________________________________________
> R-390 mailing list
> Home: http://mailman.qth.net/mailman/listinfo/r-390
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:R-390 at mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html