[R-390] Tuning SSB
Larry Haney
larry41gm2 at gmail.com
Tue Oct 1 09:42:58 EDT 2024
Let me clarify the type of noise I'm referring to, it's the QRN/QRM
(static, electrical interference, arcing or vehicle ignition system) type
of noise, not the normal smooth noise generated by the electronics (tubes,
resistors, etc) of the rx. IE, I'm referring to the type of AM noise that
comes in on the antenna that the AM noise limiter on the R-390A is fairly
good at suppressing.
And in reference to the product detector conversion noise (the noise you
hear when no signal is being received) is lower than the conversion noise
created by the envelope detector with the BFO injection conversion noise,
the product detector is considerably lower in conversion noise. Perhaps I'm
wrong in calling it conversion noise, If there's a better term, please let
me know.
Regards, Larry
On Tue, Oct 1, 2024 at 5:03 AM Francesco Ledda <frledda at att.net> wrote:
> Jim,
>
> I designed Costas loops for coherent optical receivers, and I never came
> across any associated noise reduction theory associated with such loop. The
> only noise reduction was due to the sideband suppression that an IQ
> receiver can provide.
>
> It is not clear to me how a product detector can reduce noise. The product
> detector has better conversion efficiency, than a single diode detector,
> that may be interpreted has noise reduction.
>
> Being an engineer, I need to see the math to understand the noise
> reduction process claimed in this chain of emails.
>
> Best, Francesco K5URG
>
>
>
>
>
> Sent from my iPad
>
> > On Oct 1, 2024, at 03:08, Jim Whartenby via R-390 <r-390 at mailman.qth.net>
> wrote:
> >
> > The link seems to me to be blurring terms. The product detector is
> described as equal to coherent detection which I believe may be better
> described as John Costas' synchronous detection. I don't see how a product
> detector oscillator is coherent with the transmitted carrier. The product
> detector frequency may be very close to being spot on with the transmitted
> carrier frequency but not so with respect to phase.
> >
> > DSBSC reception using synchronous detection has advantages over SSB in
> the presents of jamming according to Costas and is much less complicated to
> transmit. There is no need for linear power amplifiers or high Q filters.
> The original question was a comparison of the product detector with the
> envelope detector but it seems to have quickly become, at post #3 and
> after, about synchronous detectors vs envelope detectors.
> >
> > Jim
> > Logic: Method used to arrive at the wrong conclusion, with confidence.
> Murphy
> >
> > On Monday, September 30, 2024 at 10:46:03 PM CDT, Jacques Fortin <
> jacques.f at videotron.ca> wrote:
> >
> > Hello Giovanni,
> >
> > Noise reduction of an amplitude-modulated signal by a product
> demodulator vs an envelope detector is a verifiable fact.
> > I have found many explanations for this, but I believe that the thread
> from the following shortcut will provide a valid answer to your question:
> >
> https://www.edaboard.com/threads/envelope-dectector-vs-product-modulator.262958/
> >
> > For the R-390 and R-390A cases, the AGC system action time needs to be
> "speeded up" when SSB is received, without changing the global AGC behavior
> VS the AM case.
> > In other words, we need to keep the same AGC characteristic for both,
> because the global receiver behavior and the signal meter calibration
> depends on it.
> > Many attempts were made up to now (and by many people) to "improve" the
> AGC system of these receivers and the search for the best solution
> continues.
> > Some already available solutions uses external "add-on" circuitry to
> achieve the necessary goals, but simultaneously implies some compromises vs
> other receiver features, like the use of the MGC mode and the Noise Limiter
> circuit when the product detector is activated.
> > What we try to develop for some time is a self-contained solution with
> no "compromises"...
> > In that respect, I still have some (more or
>
> ______________________________________________________________
> R-390 mailing list
> Home: http://mailman.qth.net/mailman/listinfo/r-390
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:R-390 at mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
More information about the R-390
mailing list