[R-390] Filters

[Bob Camp]

Hi

That gets you away from the whole "use a scrap demo board and wire it up" approach. 

To answer the question, yes you could come up with a module that drops in where the set of IF filters used to go. Grabbing power by one or another means is likely not to hard.

Once you do all the custom design and boards, cost would be similar to an "attach to a PC" digital radio. 

Bob

On Feb 15, 2013, at 10:12 PM, "Scott Overstreet" <scott at becklawfirm.com> wrote:

> Bob---
> Can you put it all in a box that would fit in place of the mechanical filters and run on available power within that sub assembly?
> 
> Scott
> 
> 
> 
> 
> 
> 
> --- Original Message ----- From: "Bob Camp" <ham at kb8tq.com>
> To: <r-390 at mailman.qth.net>
> Sent: Friday, February 15, 2013 6:35 PM
> Subject: Re: [R-390] Filters
> 
> 
>> Hi
>> 
>> With the right hardware to target and good design software, the filters are a weekend project code. From scratch the design software stuff likely would run you < $500.
>> 
>> Bob
>> 
>> 
>> On Feb 15, 2013, at 9:22 PM, mlmccauley at att.net wrote:
>> 
>>> 
>>> Absolutely.
>>> 
>>> I've seen those come and go. The concept is great, but the market is very limited, hence the cost.
>>> 
>>> A savvy ham with the proper background could homebrew a very nice filter for a relatively cheap price. Soldering the hardware together would be a fairly easy weekend project, assuming you had a surface mount adapter board for the DSP chip. The software would take many weeks to write and even longer to debug.
>>> 
>>> 
>>> On 2/15/2013 8:05 PM, Bob Camp wrote:
>>>> Hi
>>>> 
>>>> Thus the variety of outboard dsp filter boxes that have shown up over the years. Once you get them into production, the cost is high enough that there is a very limited audience.
>>>> 
>>>> Bob
>>>> 
>>>> On Feb 15, 2013, at 8:50 PM, mlmccauley at att.net wrote:
>>>> 
>>>>> A DSP filter would be an ideal replacement for a mechanical.
>>>>> 
>>>>> DSP chips that work at 455KHz are readily available for very reasonable $.
>>>>> 
>>>>> The problem is the software.  To do a nice, flat topped, steep skirt filter would not be a trivial piece of work.
>>>>> 
>>>>> The upside is that one relatively simple circuit could be made to do everything from super-narrow CW to full bandwidth AM SWL.
>>>>> 
>>>>> 73,
>>>>> 
>>>>> Mike, WB5MYY
>>>>> 
>>>>> 
>>>>> ______________________________________________________________
>>>>> R-390 mailing list
>>>>> Home: http://mailman.qth.net/mailman/listinfo/r-390
>>>>> Help: http://mailman.qth.net/mmfaq.htm
>>>>> Post: mailto:R-390 at mailman.qth.net
>>>>> 
>>>>> This list hosted by: http://www.qsl.net
>>>>> Please help support this email list: http://www.qsl.net/donate.html
>>>> ______________________________________________________________
>>>> R-390 mailing list
>>>> Home: http://mailman.qth.net/mailman/listinfo/r-390
>>>> Help: http://mailman.qth.net/mmfaq.htm
>>>> Post: mailto:R-390 at mailman.qth.net
>>>> 
>>>> This list hosted by: http://www.qsl.net
>>>> Please help support this email list: http://www.qsl.net/donate.html
>>>> 
>>> 
>> 
>> ______________________________________________________________
>> R-390 mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/r-390
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:R-390 at mailman.qth.net
>> 
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html 
>