[R-390] Re: [Hammarlund] Tube shields? We don’t need any stinking tube shields!

[Les Locklear]

Russ,

I chose a reference point to "shoot" the temperatures from, then left the 
shields in place for 15 minutes, shot the shield temp, removed the shield, 
then shot the tube temp. I should have stated that in my post.

Les
----- Original Message ----- 
From: "Russ WQ3X" <wq3x at epix.net>
To: "Les Locklear" <leslocklear at cableone.net>
Sent: Monday, December 03, 2007 4:20 PM
Subject: Re: [Hammarlund] Tube shields? We don’t need any stinking tube 
shields!


> Hi Les -
>
> Thanks for doing this and publishing the results here. What was your 
> method of making these measurements? I think it would help in interpreting 
> the data. I'm not familiar with the capabilities of these lasar 
> thermometers.
>
> Russ Hunt WQ3X
>
>
>
>
> ----- Original Message ----- 
> From: "Les Locklear" <leslocklear at cableone.net>
> To: <r-390 at mailman.qth.net>; <Hammarlund at mailman.qth.net>
> Sent: Monday, December 03, 2007 5:09 PM
> Subject: [Hammarlund] Tube shields? We don’t need any stinking tube 
> shields!
>
>
>> Groups,
>>
>>
>>
>> This test was done using a Raytek laser digital thermometer. Temperatures 
>> were taken from a 6BZ6 1st RF amp tube on a John R. Leary SP-600JX no 
>> suffix number, serial number 1262. Ambient room temperature was 75°F. I’m 
>> not a scientist nor should this be misconstrued as a scientific test. I 
>> have always been curious as to whether the IERC tube shields “actually” 
>> prolong tube life. As noted there were several different tube shields 
>> used in this “test.” Also note there are several different types of 
>> inserts inside these tube shields.
>>
>>
>>
>> The “Real McCoy” IERC Tube Shields have a finger grip type of insert that 
>> acts as a heat sink and the test results show that the temperature 
>> difference between the shield and the tube itself is little. That should 
>> tell us that that type of shield is the “Standard.” For your information, 
>> I don’t use tube shields and my tubes seem to last a long time.
>>
>>
>>
>> Take this information as it’s meant to be, strictly informational.
>>
>>
>>
>>
>>
>>
>>
>>  1.. Shiny metal Eby tube shield no insert. 94°, bare tube 124°F.
>>
>>
>>  2.. Shiny metal Eby tube shield with seven-sided black aluminum insert. 
>> 96°F, bare tube 127°F.
>>
>>
>>  3.. Dull metal Elco tube shield no insert.108°F, bare tube 135°F.
>>
>>
>>  4.. Black heat resistant painted Eby tube shield no insert. 104°F, 126°F 
>> bare tube.
>>
>>
>>  5.. Black anodized Eby tube shield with “waveform, nine ridges” aluminum 
>> black heat shield insert. 107°F, bare tube 127°F.
>>
>>
>>  6.. Collins black anodized tube shield with “waveform, nine ridges” 
>> aluminum black heat shield. 100°F, bare tube 122°F.
>>
>>
>>  7.. W.P.M. tube shield with five-sided aluminum insert. 106°F, bare tube 
>> 118°F.
>>
>>
>>  8.. IERC tube shield with “finger grip” type beryllium insert. “The 
>> Standard.” 102°F, bare tube 104°F. ( has to be the insert)
>>
>>
>>  9.. Bare tube, no shield. 6BZ6 114°F.
>>   YMMV
>>
>>
>> Les Locklear
>> Gulfport, Ms.
>> DX'ing Since '57
>> http://www.hammarlund.info/
>>
>>
>> _______________________________________________
>> List Administrator: Duane Fischer W8DBF
>> ** For Assistance: dfischer at usol.com **
>> ----
>> http://mailman.qth.net/mailman/listinfo/hammarlund
>>
>>
>> -- 
>> No virus found in this incoming message.
>> Checked by AVG Free Edition. Version: 7.5.503 / Virus Database: 
>> 269.16.13/1165 - Release Date: 12/2/2007 8:34 PM
>>
>>
>
>
>
> -- 
> No virus found in this incoming message.
> Checked by AVG Free Edition. Version: 7.5.503 / Virus Database: 
> 269.16.13/1167 - Release Date: 12/3/2007 12:20 PM
>
>