[R-1051] mode switch

Cecil Acuff chacuff at cableone.net
Mon May 19 17:31:20 EDT 2003


I agree Steve,  I have not had to do that job....Hope I don't have too!

Cecil...
----- Original Message ----- 
From: "Steve Hobensack" <stevehobensack at yahoo.com>
To: <r-1051 at mailman.qth.net>
Sent: Monday, May 19, 2003 2:26 PM
Subject: Re: [R-1051] mode switch


> Thanks again Cecil. I removed the metal cross member
> to get at the mode switch wafers and I managed to find
> where it went. The Bfo works ok. I think changing out
> a mode switch would be about the worst repair to make
> on these units.
> Regards....Steve
> 
> --- Cecil Acuff <chacuff at cableone.net> wrote:
> > Hi Steve,
> > 
> >         Did you get any help on the piece of coax
> > that is loose.  I have
> > been catching up on a week out of town and just got
> > to your email.  I looked
> > at one in the shop and didn't see the number "4". 
> > There are two black
> > coaxes on the right side of the switch and two more
> > on the left side.  There
> > are also two with clear jackets on the left.  One of
> > the black cables on the
> > left comes around to the right side.  The center
> > conductor of the two on the
> > right side tie to the same point on the switch.  I
> > took a couple of pictures
> > if you would like me to send them.
> > 
> > Cecil...
> > ----- Original Message ----- 
> > From: "Steve Hobensack" <stevehobensack at yahoo.com>
> > To: "r1051 radio" <r-1051 at mailman.qth.net>
> > Sent: Saturday, May 17, 2003 4:49 PM
> > Subject: [R-1051] mode switch
> > 
> > 
> > > My r1051b does not work in the CW position. It
> > hears
> > > signals as if in the AM position. I found an end
> > of a
> > > piece of minature coax that broke free of the mode
> > > waffer switch. The other end of the coax goes into
> > the
> > > wire harness. I am unable to determine where the
> > > connection is located. The coax has a number "4"
> > on
> > > it. Are the coax label numbers standard? I have
> > the
> > > manual. Is there a print that shows the connection
> > and
> > > the coax id numbers? Main frame schematic figure
> > 5-1
> > > (page5-35) does not show the coax label numbers.
> > > Thanks
> > > ....Steve...KJ8L
> > >
> > > __________________________________
> > > Do you Yahoo!?
> > > The New Yahoo! Search - Faster. Easier. Bingo.
> > > http://search.yahoo.com
> > > _______________________________________________
> > > R-1051 mailing list
> > > R-1051 at mailman.qth.net
> > > http://mailman.qth.net/mailman/listinfo/r-1051
> > >
> > 
> > 
> > _______________________________________________
> > R-1051 mailing list
> > R-1051 at mailman.qth.net
> > http://mailman.qth.net/mailman/listinfo/r-1051
> 
> 
> __________________________________
> Do you Yahoo!?
> The New Yahoo! Search - Faster. Easier. Bingo.
> http://search.yahoo.com
> _______________________________________________
> R-1051 mailing list
> R-1051 at mailman.qth.net
> http://mailman.qth.net/mailman/listinfo/r-1051
> 




More information about the R-1051 mailing list