[Premium-Rx] Any expert on RFT EKD-500 out there?

[ONL4234]

Perhaps put your question to DL9HAM

http://www.ksg1300.de/

73 de Peter

***** Greetings from Flanders*****
For WJ addicts: http://www.bloggen.be/wj_interface/
Premium-Rx Mailing List
To Post: premium-rx at mailman.qth.net
For Info: http://mailman.qth.net/mailman/listinfo/premium-rx
Visit the Website: http://www.premium-rx.org



----- Original Message ----- 
From: "Karl-Arne Markström" <sm0aom at telia.com>
To: "Werner" <w.r.l at gmx.net>; <premium-rx at mailman.qth.net>
Sent: Sunday, May 06, 2007 11:10 AM
Subject: Re: [Premium-Rx] Any expert on RFT EKD-500 out there?


I am quite sure that this is the result of component ageing in one or more 
PLL loop filters.

The EKD500 family uses a multi-loop synthesizer, and it is very likely that 
a loop instability or unlock condition is more prone at some frequency 
increments due to the frequency control scheme.

Such behaviour can however be very difficult to track down as multi-loop 
synthesizers usually influence each other.

One suggestion is to monitor the VCO control voltage for each loop when 
changing frequency
and check if there are oscillations or transients on any of the loop 
voltages. Then look for component ageing in the
loop that shows the largest transients or takes the longest time to relock.

There may also be a frequency range where this can be more marked due to the 
variation of PLL loop stability margin with tuning voltage and oscillator 
presetting.

73/

Karl-Arne
SM0AOM


----- Original Message ----- 
From: "Werner" <w.r.l at gmx.net>
To: <premium-rx at mailman.qth.net>
Sent: Saturday, May 05, 2007 6:40 PM
Subject: [Premium-Rx] Any expert on RFT EKD-500 out there?


> Hi,
> I have a RFT EKD-515 for a while. It is a kind of new old stock. Was 
> produced
> in late 1990 and stored for almost 16 years. I had to fix some relais in 
> the
> preselector board. It works great so far.
> One strange behavior developed some weeks ago. Not a big problem but 
> annoying:
> When tuning the VCO (or entering the keyboard or controlling the rx from a
> PC) and a "full" 100kHz mark is passed, the PLL needs some time to adjust. 
> A
> "noise" resulting from fluctuating frequency is heard. After that 
> everything
> is stable. I doesn't matter whether the tuning increment is 10 Hz 
> (smallest
> step) or 100 Hz, 1kHz, 10 khz or anything in between. It is only important
> that a 100 khz value is a result by a tuning increment smaller than 100 
> kHz.
> Full 100 kHz tuning steps do not show this behavior. Examples:   5999.99 
> to
> 6000.00 (10 Hz increment) -> noise. 5900.00 to 6000.00 (100 Khz 
> increment) ->
> no noise.
> Again, this only happens when going over the 100 kHz mark. All other 
> frequency
> are "normal".
> Any EKD experts out there with suggestions?
> B.T.W: I have all the schematics an  the repair manual.
>
> Regards, Werner
> _______________________________________________
> Premium-Rx Mailing List
> To Post: premium-rx at mailman.qth.net
> For Info: http://mailman.qth.net/mailman/listinfo/premium-rx
> Visit the Website: http://www.premium-rx.org
> Email Help: paul at premium-rx.org
>
>
>
> -- 
> No virus found in this incoming message.
> Checked by AVG Free Edition.
> Version: 7.5.467 / Virus Database: 269.6.4/789 - Release Date: 2007-05-04 
> 17:49
>
>


-- 
No virus found in this outgoing message.
Checked by AVG Free Edition.
Version: 7.5.467 / Virus Database: 269.6.4/790 - Release Date: 2007-05-05 
10:34

_______________________________________________
Premium-Rx Mailing List
To Post: premium-rx at mailman.qth.net
For Info: http://mailman.qth.net/mailman/listinfo/premium-rx
Visit the Website: http://www.premium-rx.org
Email Help: paul at premium-rx.org