[PPRAANet] Free Tower

[KT0DX]

This tower has now been taken.

Steve
KT0DX


On 12/1/2015 02:45, DickT-W0RAA wrote:
> I received the following e-mail from Steve, KT0DX.  If anyone is interested,
> please get in touch with Steve, not me.  His e-mail is kt0dx at q.com.
>
> The previous owner was K9BWI, who is now a silent key.
>
> Please keep in mind that the listed items are FREE.  All you have to do is
> take down the tower and haul everything off.
>
> Dick
> W0RAA
>
>
> ----- Original Message -----
> From: KT0DX
> To: DickT-W0RAA
> Sent: Monday, November 30, 2015 5:20 PM
> Subject: Tower
>
>
> Dick do you know of anyone who would like a 70 foot tower with a TH7DXX and
> Rotor minus the control?  This was K9BWI's tower and is in good shape.  If
> someone was to buy everything new it would be over $3000 for what is there.
> The club president just sent me a e mail indicating that the club does not
> want it.  They are going to put up a home brewed tilt over as the 2nd tower.
> I helped them bring it back from up North and I would have never bought it
> let alone put it up...but that is just me.   If you want you can put the
> information on their reflector in case some club member wants it.  The tower
> is up and they will have to get it down NLT early spring.  I can arrange
> access to the property if I have advance notice of when someone wants to
> take it down.  Just have to notify the property owner who lives in WI.  If
> no one takes this the tower is more then likely going to come down in 1 foot
> sections.  There might be a chance I could exchange the rotor with a Tail
> Twister rotor with control so someone could have a whole system minus the
> coax and rotor cable.  Here is what is there.
>
> All items are FREE!!!!!
>
> Antenna - Hygain TH7DXX
> Tower Sections (straight) 6ea
> Top Section (Flat) BPL25G
> Thrust Bearing TB3 - (I think there is another bearing below the top one).
> Rotor Shelf AS25G (2)
> Guy Brackets GA25GD (2)
> Guy Bracket Torque Arm (6) (These attach to the Guy Bracket)
> Guy Anchors (3)  (These are the screw in type and can be removed with some
> work)
> Turn Buckle 1/2 X 9 Rohn (9)
> Equalizer Plates EP25343 (3)
> Phillystran HPTG 2100 (500 feet - estimated)
> Phillystran Big Grips (12)
> Rotor - Yaesu G1000DXA installed on tower at this time but does not have a
> control box.  I would like to swap the Yaesu rotor for a Hygain TX2 Tail
> Twister rotor with control box that I have, if I could test the Yaesu rotor
> first.  The TX2 goes for $699.00 new if you were to go out and buy it.  I
> have just rebuilt this rotor and it is like new.  The Yaesu rotor goes for
> $575.00 with control box, again, if you were to go out and buy it.
> There is about another $75.00 (also FREE) in hardware that is attached to
> the guy wires.  There is also a 2 meter vertical antenna at the top of the
> tower (Hustler I think).
>
>
> Steve
> KT0DX
>
>
>
>
>
> ---
> This email has been checked for viruses by Avast antivirus software.
> https://www.avast.com/antivirus
> ______________________________________________________________
> PPRAANet mailing list
> Home: http://mailman.qth.net/mailman/listinfo/ppraanet
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:PPRAANet at mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
>
>