[NJARC] Fannstock Clips

[Al Klase]

Hi Jerry,

The Seminar was originally scheduled for 5 May, but we're pushing it out 
due to scheduling hassles. Yes, bring the clips to the meeting.

Thanks,
Al

Jerry Dowgin wrote:
> Visit our web site - See http://www.njarc.org
> _______________________________________________
> Al
>
> When and where will the crystal set build day take place.  I have a 
> 1/2 card of 12 bags (six each) of Oneida Fannstock clips with No.6 
> mounting holes and lug type wire connection 3/4 inch long and 5/16 
> inch wide.  I would like to donate these (6 x 12 = 72) to the set 
> build if you need them.  If each set used four clips that would give 
> enough for 18 builders.  Should I bring them to the next NJARC Meeting?
>
> Jerry Dowgin
> ----- Original Message ----- From: "Al Klase" <al at ar88.net>
> To: "New Jersey Antique Radio Club" <njarc at mailman.qth.net>
> Sent: Wednesday, April 04, 2007 12:56 PM
> Subject: Re: [NJARC] A slightly off-topic request
>
>
>> Visit our web site - See http://www.njarc.org
>> _______________________________________________
>> Dave,
>>
>> Sounds like a job for X-10 remote control modules.  I think these are 
>> still available, and would be a plug-and-play solution.  Call me to 
>> discuss if you want more information.
>>
>> Al
>>
>> Dave Sica wrote:
>>> Visit our web site - See http://www.njarc.org
>>> _______________________________________________
>>> I am putting together a remote control circuit for use at our church to
>>> switch the air conditioner thermostat on and off. I salvaged circuitry
>>> from a defunct DVD player which will provide me with +5 and -5 volts DC
>>> pulses as required. Now I need to make this control a relay that will
>>> latch on with the +5 volt pulse, then latch off when hit with the -5 
>>> volt
>>> pulse.
>>> Then it hit me: I could probably design a circuit to do that using 
>>> vacuum
>>> tubes, but that doesn't really seem like the right solution here ;-)
>>>
>>> So I figured I'd toss this out to the *real* engineers out there. My
>>> grasp of solid state is kinda weak, so although I could probably muddle
>>> through this in time, I figure something like this must be the 
>>> proverbial
>>> piece of cake for a lot of our members. The circuit won't need to 
>>> switch
>>> any appreciable voltage or power, but I do want to use a physical relay
>>> rather than a solid state switch of any sort.
>>>
>>> I'll appreciate any suggestions!  I'd also like to scrounge up the
>>> necessary parts if anyone's got the appropriate stuff lying around.
>>> Thanks,
>>> --Dave Sica
>>> _______________________________________________
>>> NJARC mailing list
>>> NJARC at mailman.qth.net
>>> http://mailman.qth.net/mailman/listinfo/njarc
>>>
>>>
>>>
>>
>> -- 
>> Al Klase - N3FRQ
>> Flemington, NJ
>> http://www.skywaves.ar88.net/
>>
>>
>> _______________________________________________
>> NJARC mailing list
>> NJARC at mailman.qth.net
>> http://mailman.qth.net/mailman/listinfo/njarc 
>
> _______________________________________________
> NJARC mailing list
> NJARC at mailman.qth.net
> http://mailman.qth.net/mailman/listinfo/njarc
>
>

-- 
Al Klase - N3FRQ
Flemington, NJ
http://www.skywaves.ar88.net/