[MRCA] Sunair AN/PRC-108 backpack

[W2HX]

?while I am unfamiliar with the circuitry you are describing, i can imagine when the signal crosses from push to pull, minimizing the cross over distortion would be important. Maybe these bias pots adjust how that cross over occurs? I would stick a scope on it and watch the sine wave to see if the pots can be used to improve the signal fidelity as it crosses over.

________________________________
From: MMRCG at groups.io <MMRCG at groups.io> on behalf of Ray Fantini <RAFANTINI at salisbury.edu>
Sent: Monday, September 10, 2018 9:29 AM
To: Military Radio Collectors Association; MMRCG at groups.io; milsurplus at mailman.qth.net
Subject: [MMRCG] Sunair AN/PRC-108 backpack

Been working on getting everything together for MRCA/Gilbert and I have been working on getting my USCG AN/PRC-108 working with a whip antenna. That little back pack transceiver develops around tem watts of AM or 20 watts of SSB for operation on both 80 and 60 meters. I use this radio a lot for field operations. The radio has two outputs, one 50 Ohm output that works well with inverted V and stuff like that and provisions for a whip antenna attached to the radio. The 50 Ohm output connects to an input for the radios internal antenna tuner that has ten presets (one for each channel) and that connects to a seven foot vertical antenna attached to the side of the radio. I have been trying to get the antenna tuner set for the channels I have installed in the radio but in the process have done damage to the PA deck. Ok, so I repaired the PA deck and its working again but this is the question that I have. The PA deck has two stages with the first being a driver in push pull and the second being a power amplifier in push pull. Both stages have a bias pot that allows a small level of DC, maybe under 2 volts to ground depending on the setting of the pot to forward bias the amplifiers. I thought this may affect gain of the stages but apparently has almost no effect on the output, maybe a watt at the most. What are these bias pots for? How do I set them? Were they intended to set idle current for the amplifiers? Are they used for adjust linearity? Or distortion?
This radio was built by Sunair back in the seventies for the USCG to operate on HF AM/SSB before VHF took over everything, at least in portable operation. All runs from one twelve volt gel cell and have been using it for a while now on the 60 Meter USB M&S Net and want to use it as a portable for 60 and 80 meters at Gilbert so that why I am doing all this damage to it to get it working with a whip.

Ray F/KA3EKH
_._,_._,_
________________________________
Groups.io Links:

You receive all messages sent to this group.

View/Reply Online (#236)<https://groups.io/g/MMRCG/message/236> | Reply To Group<mailto:MMRCG at groups.io?subject=Re:%20%5BMMRCG%5D%20Sunair%20AN%2FPRC-108%20backpack> | Reply To Sender<mailto:RAFANTINI at salisbury.edu?subject=Private:%20Re:%20%5BMMRCG%5D%20Sunair%20AN%2FPRC-108%20backpack> | Mute This Topic<https://groups.io/mt/25501173/91829> | New Topic<https://groups.io/g/MMRCG/post>

Your Subscription<https://groups.io/g/MMRCG/editsub/91829> | Contact Group Owner<mailto:MMRCG+owner at groups.io> | Unsubscribe<https://groups.io/g/MMRCG/leave/2229464/2047677869/xyzzy> [w2hx at w2hx.com]

_._,_._,_

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://mailman.qth.net/pipermail/mrca/attachments/20180910/a99f7cbf/attachment.html>