[MRCA] Mini Speaker Amplifier LM386 tips

[Ray Fantini]

We're talking boat anchors here!, batteries are going to suffer no matter what. You want something that can be heard over the fans and dynamotors!  I want it to be big and loud because otherwise what's the point , you may just as well be wearing headsets.

Ray F

-----Original Message-----
From: MRCA [mailto:mrca-bounces at mailman.qth.net] On Behalf Of Al Klase
Sent: Tuesday, March 31, 2015 2:16 PM
To: mrca at mailman.qth.net
Subject: Re: [MRCA] Mini Speaker Amplifier LM386 tips

Ray and Zorro,

The difference is the LM-386 was designed to run of a modest power supply, e.g. 9-volt battery, while the LM-383 is lusting after a Sears Diehard.
Typical no signal currents are 4 ma. and 45 ma. respectively.

There might be modern class-D (switching) devices that would let you have you cake and eat it too. Anybody have a handle on these?

LM-386 kits, jack, volume control, PCB etc are dirt cheap out of China via E-bay.

Al

Al Klase - N3FRQ
Jersey City, NJ
http://www.skywaves.ar88.net/

On 3/31/2015 1:31 PM, Ray Fantini wrote:
> The LM-386 is a fairly piss week device with maybe a half watt output at best. Instead of wasting time with that the LM-383 will provide five to six watts of output into a 4 ohm load, requires a minimum of external components and has output protection to take care of shorts or thermal issues. The 383 was designed from the ground up as an audio power amplifier, the 386 works for that but is perhaps more a general use op amp? The only bad thing about the 383 for mill use is its maximum recommended device voltage is 20 VDC but it will withstand up to 40 so it's not designed to be connected directly to a 24 volt bus.
>
> Ray F
>
> -----Original Message-----
> From: MRCA [mailto:mrca-bounces at mailman.qth.net] On Behalf Of B. Smith
> Sent: Tuesday, March 31, 2015 11:48 AM
> To: mrca at mailman.qth.net
> Subject: [MRCA] Mini Speaker Amplifier LM386 tips
>
>            When building your own "mini" audio amplifier  for your military radio using the LM386 chip it is important to not get greedy with the gain of the chip.  The chip has "default" amplification factor of 20 without any external caps or resistors. I suggest that you start off with that default  gain of 20  when using a military handset  set audio to drive the input. Combinations of caps and resistors between pins 1 and 8 can be added to allow selection of various  gain levels from 20 to 200! It is very easy to overdrive the chip with the high audio level from a military radio resulting in distortion.  Consult the data sheet for the chip for examples of different gain settings.
> The Radio Shack amp uses a unique 1 transistor stage prior to the 
> LM386 and varies the gain on that transistor prior to the input of the 
> LM386 -
> - - it is a great circuit and easily copied.  Then following that single transistor stage  on the Radio Shack amp using the  LM386 a combination of 10uF and a 100 ohm resistor is utilized between pins 1 and 8 to allow a fixed gain setting.
> Z
>
> ______________________________________________________________
> MRCA mailing list
> Home: http://mailman.qth.net/mailman/listinfo/mrca
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:MRCA at mailman.qth.net
>
> This list hosted by: http://www.qsl.net Please help support this email 
> list: http://www.qsl.net/donate.html 
> ______________________________________________________________
> MRCA mailing list
> Home: http://mailman.qth.net/mailman/listinfo/mrca
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:MRCA at mailman.qth.net
>
> This list hosted by: http://www.qsl.net Please help support this email 
> list: http://www.qsl.net/donate.html

______________________________________________________________
MRCA mailing list
Home: http://mailman.qth.net/mailman/listinfo/mrca
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:MRCA at mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html