[Motorola] Mitrek Mobile Setup Questions

Thu, 14 Feb 2002 00:07:04 -0500 (EST)

If you are looing for somewhere to post a question if you can't find an
answer - try my board - http://radio.the161.net.  Since Batlabs's board is
still down, I have put forums up for Motorola stuff for the time being,
when their board comes back up, I'll lock the ones on my board for
archvial purposes.

-Alex

On Wed, 13 Feb 2002, John Flint wrote:

> Thanks for the tip, I knew about Batlabs, it just did not occur to me to =
look
> there!  Duh.  Anyway. found the info on the PL deck, one question down an=
d one
> to go.
>
> Thanks again,
>
> JRF
>
> Jim wrote:
>
> > Try this link...
> >
> > http://www.repeater-builder.com/rbtip/
> >
> > Or this:
> >
> > http://www.batlabs.com/
> >
> > Good luck
> > Jim W7RY
> >
> > ----- Original Message -----
> > From: Paul Cavnar <[email protected]>
> > To: <[email protected]>
> > Sent: Sunday, February 10, 2002 15:58
> > Subject: Re: [Motorola] Mitrek Mobile Setup Questions
> >
> > | Hi John -
> > |
> > | I don't have the information at hand but, there is a neat little web
> > | page that shows the tune-up procedure. It is at:
> > | http://www.qsl.net/sra/mitrektx.gif
> > |
> > | The receiver tune up page is at:
> > | http://www.qsl.net/sra/mitrekrx.gif
> > |
> > | Hope this helps.
> > |
> > | Paul - NN7B
> > |
> > | ----- Original Message -----
> > | From: "John Flint" <[email protected]>
> > | To: "Motorola Listserv" <[email protected]>
> > | Sent: Sunday, February 10, 2002 3:48 PM
> > | Subject: [Motorola] Mitrek Mobile Setup Questions
> > |
> > |
> > | I have a couple of questions regarding a high band, high power Mitrek
> > | (T83JJA3900BK) that I am putting into service.  Unfortunately, I only
> > | have an older low power manual.
> > |
> > | First question:  Setting the output power - There are two pots on the
> > | main board; R909 (orange, power set) and R911 (blue, max power).  I
> > | presume these operate as on the low power TX.  Is the yellow  pot on =
the
> > | PA is also related to these adjustments?  What is the procedure for
> > | setting all three pots?
> > |
> > | Second question:  PL board jumpers - This is a HLN4181APR PL board.
> > | Need the functions of the following jumpers.
> > |
> > | JU1 out
> > | JU2 out
> > | JU3 in
> > | JU4 in "and" squelch??
> > | JU5 out "or" squelch??
> > | JU6 out
> > | JU7 out
> > | JU8 in
> > |
> > |
> > | Thanks in advance, reply direct.
> > |
> > | John R. Flint
> > | KA=D8LDB
> > |
> > | _______________________________________________
> > | Motorola mailing list
> > | [email protected]
> > | http://mailman.qth.net/mailman/listinfo/motorola
> > |
> > |
> > | _______________________________________________
> > | Motorola mailing list
> > | [email protected]
> > | http://mailman.qth.net/mailman/listinfo/motorola
> >
> > _______________________________________________
> > Motorola mailing list
> > [email protected]
> > http://mailman.qth.net/mailman/listinfo/motorola
>
> _______________________________________________
> Motorola mailing list
> [email protected]
> http://mailman.qth.net/mailman/listinfo/motorola
>