[Milsurplus] [MRCA] Russian US-P Receiver

[Ian Wilson]

There is a 6H6G - shows up in various places on a search, so should
be able to find one (I have one here somewhere, but no chance of
finding it in finite time at the moment).

73, ian K3IMW


On Wed, Sep 9, 2015 at 8:04 AM, Ray Fantini <RAFANTINI at salisbury.edu> wrote:

> Wow, did not notice that being the detector and audio stages were just
> about the only part that was not hacked up. Whoever did the conversion from
> 24 volt filament to 6 volt did possibly the worst soldering and wiring job
> I have seen yet with assorted lengths of wire run all over the place and
> poorly soldered to the tube sockets. I did keep the receiver wired for 6
> volt filament but cleaned up all the pervious mess and use all yellow wire
> to make everything match.  All the mechanical tuning assembly had to be
> removed, cleaned and lubricated and do have it working correctly but have
> to wonder how anyone was supposed to tune that radio accurately when the
> tuning mechanism is so course? The fine tuning works but still getting the
> radio in the right neighborhood is a chore.  Had issues with the three gang
> tuning capacitor with the brass bearing retainer and brass end screw
> assembly not being held tightly in the pot meatal of the capacitor body and
> ended up removing the entire assembly, cleaning and having to use a small
> amount of epoxy to secure the brass assemblies to the capacitor being the
> original press fittings were no longer snug. Have to wonder if this is an
> effect of the ageing of the pot meatal?
> Will try change to the detector tonight and see how that works out but
> wonder if will also affect AVC action ? Also I did notice that the 6H6 is
> not quite up to what it should be on the tube tester when I checked it and
> hate to replace it with an American 6H6 being the Russian 6H6 is a full
> size glass tube, way better looking than the squat little American 6H6.
> I have to wonder what the possibility of getting a Russian 6X6 is?
>
> RF
>
> From: Meir WF2U [mailto:wf2u at ws19ops.com]
> Sent: Tuesday, September 08, 2015 5:37 PM
> To: Ray Fantini; Military Surplus Mail List; MRCA at mailman.qth.net
> Subject: Re: [MRCA] Russian US-P Receiver
>
> Ray,
>
> The US-P receiver sensitivity is an issue in the original configuration.
> The sensitivity is limited as a way to implement a crude noise limiter
> which is operating all the time in both AM and CW. This is done by biasing
> the cathodes of the dual-diode detector/noise limiter tube 6H6 (6X6 in
> Cyrillic) to 3 volts by tying the cathodes to the cathode of the audio
> output 6K7 tube which is at 3 volts due to the cathode resistor. This means
> that the signal going into the detector has to be above the 3 volt
> threshold in order to be detected. Modify the circuit by removing both
> cathodes of the 6X6 from the cathode of the 6K7, tie them together to the
> ground. This increases the sensitivity to normal for this kind of tube
> line-up.
>
> 73, Meir WF2U
> Landrum, SC
> On September 8, 2015 2:19:36 PM EDT, Ray Fantini <RAFANTINI at salisbury.edu
> <mailto:RAFANTINI at salisbury.edu>> wrote:
> I have a Russian US-P receiver that I received from the Ukraine the other
> day. The US-P is a small eight tube superhet that was used as both a field
> radio in the RSB luggable radio set or in various aircraft, manufactured
> during the war till the mid-fifties. The receiver uses all 6K7 tubes with
> one for the first RF, Oscillator, first and second IF and audio amplifier
> with the only other two tubes being a 6A7 as a mixer and 6H6 as a detector
> and AVC. There is also a 6K7 for the BFO.
> If anything this radio is something like the tube lineup and design of an
> ARC-5 style receiver except unlike the ARC-5 this radio has five bands and
> covers 150 KC to 12 MC.
> The radio had been the victim of much eastern bloc hacking and after
> restoring much of the circuit to its original condition now it’s working
> but have been having issues with low sensitivity. It requires around two to
> three hundred microvolts before you start to get solid static free copy and
> two to four mill volts before there is any AVC action. Although this works
> fairly well on the AM broadcast band and on high powered shortwave
> broadcast stations it still leaves a lot to be desired. I have checked all
> the bypass capacitors and screen and plate voltages, cathode bias resistors
> and the AVC bus for any leakage but everything checks good. Did pull all
> the tubes and test them in my TV-10 and replaced two of the 6K7 tubes with
> US versions of that tube but going to assume a Russian 6K7 is the same as a
> US 6K7. All the alignment looks just about right but still stumped by the
> lack of sensitivity. The IF has two stages and operates at 110 KC and I
> think that’s where I am not seeing enough gain. The radio works ok on the
> local AM broadcast stations and sound surprisingly good for its age. I
> built  an external power supply for the receiver that has an additional
> audio stage built around a 6AQ5 so it can drive a speaker as opposed to the
> original sets audio output that was designed around a high impedance
> headphone system. Do plan to have this at Gilbert if anyone wants to see it
> in person and if anyone has any speculation of where the additional gain is
> let me know.
>
>
> Ray F/KA3EKH
>
> ________________________________
>
> MRCA mailing list
> Home: http://mailman.qth.net/mailman/listinfo/mrca
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:MRCA at mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
>
> --
> Sent from my Android device with K-9 Mail. Please excuse my brevity.
> ______________________________________________________________
> Milsurplus mailing list
> Home: http://mailman.qth.net/mailman/listinfo/milsurplus
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Milsurplus at mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
>