[Lowfer] Lowfer KE

[KA4SEY]

John,I could if I had a variable power supply. I could just hook it up to the drop cords and test away. I'm sure I can find something. KaseySent from my Verizon, Samsung Galaxy smartphone
-------- Original message --------From: John Hamer <wilbur0611 at gmail.com> Date: 11/22/20  10:19 AM  (GMT-05:00) To: "Discussion of the Lowfer (US, European, & UK) and MedFer bands" <lowfer at mailman.qth.net> Subject: Re: [Lowfer] Lowfer KE Kasey,My antenna draws around 45ma at 22v. I don't know what your antenna does,but higher voltage should give you higher current. Do you have a way toadjust the voltage between 13 and 24 so you can see at what point it drops?Regards,John HamerLowfer JHOn Sun, Nov 22, 2020, 10:07 AM KA4SEY <ka4sey at gmail.com> wrote:> John,Glad you could get it going, I'm messing around with 13.8 and 24> volts and 13.8 seem s to work better? Now sure why but on 24 it draws 20ma> and on 13.8 it draws 40ma. At 13.8 it also has a stronger signal here at> the house. Not sure if that's overloading it or what.KaseySent from my> Verizon, Samsung Galaxy smartphone> -------- Original message --------From: John Hamer <wilbur0611 at gmail.com>> Date: 11/22/20  9:53 AM  (GMT-05:00) To: "Discussion of the Lowfer (US,> European, & UK) and MedFer bands" <lowfer at mailman.qth.net> Subject: Re:> [Lowfer] Lowfer KE Kasey,That sounds good.  You are going to need the 24v> to get 1 watt with thatconfiguration. I think it will work better for you.> It made a bigdifference for me. The new computer is working well.  I have> been going through windowsupdates for hours because it has been off for> years,  but it's almostthere.RegardsJohn HamerLowfer JHOn Sun, Nov 22,> 2020, 9:48 AM KA4SEY <ka4sey at gmail.com> wrote:> Hey John, how is your> computer setup doing? I meant to tell you, I took> the LPF out and both> transistor are doing good. I put a 10W 50 ohm resistor> from the output to> ground and supplied 24v to the circuit and got 75ma to> the finals. It was> putting out a whopping 1.8 watts! The resistor even got> got. I'm excited!> Now with it out of line and back at the antenna it's on a> 13.8v power> supply with the same configuration and I was getting 35ma to> the finals. I> believe that's about 450mw. But looking at the signal here on> the radio> it's much stronger. I even picked the tub up and sat a milk crate> under it> and now it's a strong 20 over. So both of those helped. I will try> the> configuration you told me to try today and see how that goes. I might> try> the thing on 24 volts and see if the signal increases.KaseySent from my>> Verizon, Samsung Galaxy smartphone> -------- Original message --------From:> John Hamer <wilbur0611 at gmail.com>> Date: 11/22/20  9:38 AM  (GMT-05:00)> To: "Discussion of the Lowfer (US,> European, & UK) and MedFer bands" <> lowfer at mailman.qth.net> Subject: Re:> [Lowfer] Lowfer KE I Believe he has> the capacitors on the oscillator and> they are just not onthe schematic he> posted.  I went through datasheet with> him over the summerand calculated> the proper capacitor values.RegardsJohn> HamerLowfer JHOn Sun, Nov 22,> 2020, 9:28 AM KA4SEY <ka4sey at gmail.com>> wrote:> Thank you John, I will> add those capacitors on in the future and> make any> other changes. Like I> said I'm going to try another configuration> with the> coil today to see if> it will do any better. I will hopefully find> an> ammeter which would help> me a lot. Thanks againKaseySent from my> Verizon,> Samsung Galaxy> smartphone> -------- Original message> --------From: J D <> listread at lwca.org> Date:> 11/22/20  2:27 AM> (GMT-05:00) To:> lowfer at mailman.qth.net Subject: Re:> [Lowfer] Lowfer KE> Kasey, it would> appear from your schematic that a few> components may be> missing, thereby> preventing your oscillator from being as> stable as it> needs to be. This> same situation is found in a commercially> made sorta-kit> rig for 22> meters, and beacons using it there can often be> identified by> their> tendency to wander or even outright jump around in> frequency from> day to> day.A Pierce oscillator needs capacitance from both> legs of the> crystal> to ground as part of a phase shift network. There is> stray> capacitance> present, of course, without which it would not oscillate> at> all; but that> is neither of sufficient magnitude nor stability to ensure>> reliable> oscillation at the design frequency of the crystal. A good>> starting value> for capacitors for a typical 3 MHz parallel resonant> crystal> would be 27> pF each.In addition, there n>  eeds to be a series> resistor between pin 10> and the crystal. It serves> three functions that> each affect frequency> stability to a certain extent:> it isolates the> crystal somewhat from the> complex impedance of the gate> output, it limits> current and thereby power> dissipation in the crystal, and> it is part of> the phase delay network. As> a rough first approximation, I'd> suggest 1 K,> maybe as high as 2.2> K.Finally, the shunt resistance across> the crystal> could be a little> higher in value for 3 MHz operation, such as> 3.3 M to> 4.7 M. It's not> terribly critical, but it is preferable to operate> it with> as high a> value as will allow for reliable startup. Lowering the> operating> Q of the> crystal with a low parallel resistance could allow a> crystal to> jump too> easily between primary resonance and any secondary> resonance> modes it may> have.These comments are some basic rule of thumb> guidance.> For more> detailed treatment of Pierce oscillators implemented> with logic> gates, I> believe Crystek s>  till offers this article:>>> https://www.crystek.com/documents/appnotes/pierce-gateintroduction.pdfJohn>>> Davis______________________________________________________________Lowfer>>> mailing listHome: http://mailman.qth.net/mailman/listinfo/lowferHelp:>>> http://mailman.qth.net/mmfaq.htmPost: mailto:Lowfer at mailman.qth.netPost>>> must be less than 50KB total for message plus attachment!This list hosted>>> by: http://www.qsl.netPlease help support this email list:>>> http://www.qsl.net/donate.html>>> ______________________________________________________________> Lowfer>> mailing list> Home: http://mailman.qth.net/mailman/listinfo/lowfer>> Help:> http://mailman.qth.net/mmfaq.htm> Post: mailto:> Lowfer at mailman.qth.net>> Post must be less than 50KB total for message> plus attachment!>> This list> hosted by: http://www.qsl.net> Please help> support this email list:> http://www.qsl.net/donate.html>______________________________________________________________Lowfer>> mailing listHome: http://mailman.qth.net/mailman/listinfo/lowferHelp:>> http://mailman.qth.net/mmfaq.htmPost: mailto:Lowfer at mailman.qth.netPost>> must be less than 50KB total for message plus attachment!This list hosted>> by: http://www.qsl.netPlease help support this email list:>> http://www.qsl.net/donate.html>> ______________________________________________________________> Lowfer> mailing list> Home: http://mailman.qth.net/mailman/listinfo/lowfer> Help:> http://mailman.qth.net/mmfaq.htm> Post: mailto:Lowfer at mailman.qth.net>> Post must be less than 50KB total for message plus attachment!>> This list> hosted by: http://www.qsl.net> Please help support this email list:> http://www.qsl.net/donate.html______________________________________________________________Lowfer> mailing listHome: http://mailman.qth.net/mailman/listinfo/lowferHelp:> http://mailman.qth.net/mmfaq.htmPost: mailto:Lowfer at mailman.qth.netPost> must be less than 50KB total for message plus attachment!This list hosted> by: http://www.qsl.netPlease help support this email list:> http://www.qsl.net/donate.html> ______________________________________________________________> Lowfer mailing list> Home: http://mailman.qth.net/mailman/listinfo/lowfer> Help: http://mailman.qth.net/mmfaq.htm> Post: mailto:Lowfer at mailman.qth.net> Post must be less than 50KB total for message plus attachment!>> This list hosted by: http://www.qsl.net> Please help support this email list: http://www.qsl.net/donate.html______________________________________________________________Lowfer mailing listHome: http://mailman.qth.net/mailman/listinfo/lowferHelp: http://mailman.qth.net/mmfaq.htmPost: mailto:Lowfer at mailman.qth.netPost must be less than 50KB total for message plus attachment!This list hosted by: http://www.qsl.netPlease help support this email list: http://www.qsl.net/donate.html