[Lowfer] WD2XNS in WOLF mode

[pbunn]

Not sure Jay. I tried several ways. The frequency was close when I calibrated. When I would return to receive node, the program would default to start up and go to the default audio interface which was incorrect. When I corrected it the program would freeze . If I run with no calibration  it decoded jiberish. Your signal was plenty loud and I could hear you change power levels.

Pat
N4LTA

jrusgrove at comcast.net wrote:


Pat

Dunno about Win7 ... I'm still (happily) in the stoneage with XP.

If you run Mode > Frequency before going to the cal screen you should get a frequency readout of
your frequency at 'P:' on the top of the screen . In XP, the cal procedure imports this number into
the cal routine. You could just enter it manually.

Hope this helps.

Jay

----- Original Message -----
From: <pbunn at patbunn.com>
To: "Discussion of the Lowfer (US, European, &amp;UK) and MedFer bands" <lowfer at mailman.qth.net>
Sent: Saturday, February 16, 2013 10:58 AM
Subject: Re: [Lowfer] WD2XNS in WOLF mode


>I have you on the screen now but no decoding/. The cal routine does not seem to work with Win 7.
>When I input the audio signal, it asked for the displayed value on the wolf screen, but you can't
>see that value because the cal screen covers it and I can't figure out how to see the value that
>needs to be input. Also locked up about 4 times.
>
> Pat
> N4LTA
>
>
>
> -----Original Message-----
> From: jrusgrove at comcast.net
> Sent: Saturday, February 16, 2013 2:41 PM
> To: lowfer at mailman.qth.net
> Subject: [Lowfer] WD2XNS in WOLF mode
>
> WD2XNS will be transmitting in WOLF mode for the next couple hours on 136.800 kHz. Power level
> will
> be adjusted up and down and will be indicated in the message.
>
> The GUI version of the decoder can be found at http://www.qsl.net/d/dl4yhf/wolf/index.html . Be
> advised that this mode is more critical than most in terms of sound card calibration. There is a
> cal
> routine in the software if you have a known frequency source.
>
> Reports are appreciated.
>
> Jay W1VD  WD2XNS  WE2XGR/2
>
> ______________________________________________________________
> Lowfer mailing list
> Home: http://mailman.qth.net/mailman/listinfo/lowfer
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Lowfer at mailman.qth.net
> Post must be less than 50KB total for message plus attachment!
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> ______________________________________________________________
> Lowfer mailing list
> Home: http://mailman.qth.net/mailman/listinfo/lowfer
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Lowfer at mailman.qth.net
> Post must be less than 50KB total for message plus attachment!
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html

______________________________________________________________
Lowfer mailing list
Home: http://mailman.qth.net/mailman/listinfo/lowfer
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Lowfer at mailman.qth.net
Post must be less than 50KB total for message plus attachment!

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html