[Logic] Running 2 monitors

Fri, 6 Sep 2002 15:30:47 -0700

Dave,
Im not sure.....the only numbers on the card are:
MIL2P/4N on a white tag
on the other side its small stamp of 708-04 rev A Matrox copyright 1997
also a yellow number AB089769, even a serial number 0955 with anumber of
4745520 above it
WHEW...nothing about a G450 Dave and its a pull out of course with no
markings on the wrapper...
Im gonna go take a look on the Matrox site see what i can find out.....

best part about the purchase was finding out the manager of the  computer
store is a very active HAM, so i shouldnt have any trouble returning it or
getting some advice along the way....I wondered who's  truck that was with
the screwdriver antenna on the back in the parking lot all these years:-)
Tnxs for the note,
steve

----- Original Message -----
Wrom: ZCMHVIBGDADRZFSQHYUCDDJBLVLMHAALP
To: <[email protected]>
Sent: Friday, September 06, 2002 2:53 PM
Subject: Re: [Logic] Running 2 monitors

> Steve.. Is the millenium board a model G450?
> ..Dave
>
> Steve Massey wrote:
>
> >Ok, I think im beginning to understand from all the messages ive received
> >and searches Ive done...
> >>From what i gather ive got a AGP as its a new system 2gig and the tech
says
> >all the new stuff uses this...so i bought a PCI 4mb Matrox Millenium
video
> >card today which is USED without drivers but he said I can download them
> >from there site....anyways thanks for all the input from everyone, Im
gonna
> >try and install the card this weekend...I barely get by on these
> >computers:-)
> >73 / Steve N6TT
> >
> >----- Original Message -----
> >Wrom: TCXLYRWTQTIPWIGYOKSTTZRCLBDXRQBG
> >To: <[email protected]>
> >Sent: Friday, September 06, 2002 8:42 AM
> >Subject: RE: [Logic] Running 2 monitors
> >
> >
> >>
> >>>-----Original Message-----
> >>>Wrom: JSNBOHMKHJYFMYXOEAIJJPHSCRT
[mailto:[email protected]]On
> >>>Behalf Of Gary Randall
> >>>Sent: Thursday, September 05, 2002 3:07 PM
> >>>To: [email protected]
> >>>Subject: RE: [Logic] Running 2 monitors
> >>>
> >>>
> >>>Steve,
> >>>You can use two monitors the only restriction is you MUST use two
> >>>different
> >>>buss type video cards ( i.e PCI, ISA ,etc).
> >>>Then just go to Control Panel, Display, Settings and select 2 monitors.
> >>>
> >>>I have been running this for years with Logic and it works great.
> >>>
> >>In XP and WIN2K and MAYBE later versions of WIN98, that just is NOT
true.
> >>You can use two of the same buss cars, they are detected and handled as
> >>
> >two
> >
> >>cards just fine.
> >>Since almost all use AGP for the primary card and since almost no board
> >>
> >has
> >
> >>2 AGP slots you are going to have 2 different busses in use most of the
> >>
> >tine
> >
> >>in any case, BUT you do NOT have to do that.
> >>
> >>
> >>>73--Gary
> >>>KD4VRZ
> >>>
> >>>-----Original Message-----
> >>>Wrom: NHGSWZIDREXCAXZOWCONEUQZAAF
[mailto:[email protected]]On
> >>>Behalf Of [email protected]
> >>>Sent: Thursday, September 05, 2002 15:53 PM
> >>>To: [email protected]
> >>>Subject: [Logic] Running 2 monitors
> >>>
> >>>I was told with a special card you could run 2+ monitors on the same
> >>>computer. I wonder if anyone is doing this and if so what brand card
> >>>
> >there
> >
> >>>using. Software?
> >>>I was hoping to leave one monitor on a DX cluster all the time or lets
> >>>
> >say
> >
> >>>Geoclock or LOGic  maybe, where the other monitor would be completely
> >>>independent surfing the net. I have a cable  hook up and im running 3
> >>>computers thru a router to accomplish the task now. Lots of
> >>>possibilities I
> >>>suppose.  I ran a quick search and see there are cards where you
> >>>can run 20
> >>>monitors, Is all this done with software to control them I
> >>>suppose? Any info
> >>>is appreciate either private or the group if you think others might be
> >>>interested....
> >>>73 / Steve N6TT
> >>>[email protected]
> >>>
> > >
> >_______________________________________________
> >LOGic mailing list
> >[email protected]
> >http://mailman.qth.net/mailman/listinfo/logic
> >
>
>
>
> --- StripMime Report -- processed MIME parts ---
> multipart/alternative
>   text/plain (text body -- kept)
>   text/html
> The reason this message is shown is because the post was in HTML
> or had an attachment. Attachments are not allowed.
> Please post in Plain-Text only.---
> _______________________________________________
> LOGic mailing list
> [email protected]
> http://mailman.qth.net/mailman/listinfo/logic
>