Re[2]: [Logic] QSX Radio frequency

Sat, 23 Mar 2002 13:25:38 -0500

I have not tried TRX so I can't comment.  It does explain how Logic operates
though.....
WriteLog gets around the problem by constantly polling the radio.  For
OMNI-VI+ users CdE is set OFF when using W/L and ON for Logic.
Jim

> TRX does cause the split to occur, but if you watch the process, it looks
as
> if things are jumping around. TRX has to set one VFO, then makes the other
> vfo active so that it can be set, sets that vfo, then switches VFO's back
> and turns on split mode.
>
> From TRX manager's help file:
>
> "ICOM transceivers communicate, by interrupt, frequency and mode changes
but
> other parameters (channel number, Split mode, VFO.) that are made on the
> transceiver are not transmitted to the PC.  The consequences are the
> following :
>
> - after the launching of TRX-Manager, some parameters are fixed by default
> or unavailable. The display  progressively becomes visible as commands are
> sent from the PC.  If necessary, rotate the dial tuning to display the
> frequency,
>
> - it is thus recommended to change the VFOs or to switch the SPLIT mode
from
> the PC."
>
> Ben
> ----- Original Message -----
> From: "NL7ZL" <[email protected]>
> To: <[email protected]>
> Sent: Saturday, March 23, 2002 09:42
> Subject: Re[2]: [Logic] QSX Radio frequency
>
>
> > I ran into this same problem using an ICOM 756 PRO.  If you are using
> > TRX-Manager then split works fine.  I talked to the folks at Logic and
> > they  are aware of this.  Their Icom driver does not appear to work as
> > good as the on in TRX-Manager.
> >
> >
> >
> > --
> > 73,
> >
> > Tom                            mailto:[email protected]
> >
> > Saturday, March 23, 2002, 10:02:15 AM, you wrote:
> >
> > BHN> On some radios, Icoms come to mind, the TX VFO frequency cannot be
> read by
> > BHN> the computer unless it is made the active VFO.
> >
> > BHN> Ben
> > BHN> ----- Original Message -----
> > BHN> From: "Jim Brannigan" <[email protected]>
> > BHN> To: <[email protected]>
> > BHN> Sent: Saturday, March 23, 2002 08:54
> > BHN> Subject: Re: [Logic] QSX Radio frequency
> >
> >
> > >> A note to OMNI-VI+ users.
> > >> I find that if I set the split from the radio, Logic6 will not log
the
> > BHN> Xmt.
> > >> Freq.
> > >> If I set the split from the log window, the Xmt. freq. is logged and
> the
> > >> packet QSX is sent.
> > >> This is a problem with the Ten Tec software.
> > >> Jim
> > >>
> > >> > Hi
> > >> > The split Frequency  works Fine for me and automatically on my
> > >> > Kenwood 950 SDX that is connected to the computer via com 1 via
> Kenwood
> > >> > interface IF-232C
> > >> > In other words if your radio is connected to the computer and logic
> can
> > >> > control it  the split frequency works automatically
> > >> >
> > >> > 73 Eli  4z5is
> > >> >
> > >> > Stern Eli  Advocate & Notary
> > >> > ham radio callsign    4Z5 IS
> > >> > ____________________________________
> > >> > [email protected]                  OFFICE
> > >> >
> > >> > Haberman Dovev & Stern advocates & notarie  Office
> > >> > 51 Wizman St Tel Aviv Israel
> > >> > FAX  00972 3 6962206
> > >> >
> > >> > [email protected]           HOME
> > >> >
> > >> > 2 sagie st P.O.BOX 728   Reut ISRAEL 71908
> > >> > Fax  00 972 8 9710010
> > >> >
> > >> >
> > >> >
> > >> > -----Original Message-----
> > >> > From: [email protected]
> [mailto:[email protected]]
> > >> > On Behalf Of GilBaronW0MN
> > >> > Sent: Saturday, March 23, 2002 3:14 PM
> > >> > To: AA/Logic
> > >> > Subject: [Logic] QSX Radio frequency
> > >> >
> > >> > In the log form there is a field for transmit frequency when
> operating
> > >> > split. Is there a way to automatically update this field to the
exact
> > >> > transmitted frequency as read from the rig rather than nothing or
> > >> > offset?
> > >> > I would like the program to read the other vfo and enter the
> frequency
> > >> > here.
> > >> > It would make sending spots so much more useful. On clusters if you
> have
> > >> > QSX
> > >> > (XMIT FREQ) then the spot logs will show this and logic users and
> others
> > >> > that have the feature can set the split automatically. Since the
set
> rig
> > >> > automatically sets the split if on the spot log, that  means it has
> > >> > access
> > >> > to the other vfo. I assume there should be a way to read it also.
Is
> > >> > there a
> > >> > way to do that or do you have to manually enter this field?
> > >> >
> > >> >
> > >> > Gil Baron http://webpages.charter.net/gbaron
> > >> > 44.08208 N 92.51263 W 1055'
> > >> > "Hierro candente, batir de repente"
> > >> >
> > >> >
> > >> > _______________________________________________
> > >> > LOGic mailing list
> > >> > [email protected]
> > >> > http://mailman.qth.net/mailman/listinfo/logic
> > >> >
> > >> > _______________________________________________
> > >> > LOGic mailing list
> > >> > [email protected]
> > >> > http://mailman.qth.net/mailman/listinfo/logic
> > >>
> > >> _______________________________________________
> > >> LOGic mailing list
> > >> [email protected]
> > >> http://mailman.qth.net/mailman/listinfo/logic
> > >>
> >
> > BHN> _______________________________________________
> > BHN> LOGic mailing list
> > BHN> [email protected]
> > BHN> http://mailman.qth.net/mailman/listinfo/logic
> >
> > _______________________________________________
> > LOGic mailing list
> > [email protected]
> > http://mailman.qth.net/mailman/listinfo/logic
> >
>
> _______________________________________________
> LOGic mailing list
> [email protected]
> http://mailman.qth.net/mailman/listinfo/logic