From kenw8ek at gmail.com Fri Feb 1 10:47:39 2019 From: kenw8ek at gmail.com (Ken, W8EK) Date: Fri, 1 Feb 2019 10:47:39 -0500 Subject: [Kenwood] Crystals, Phone Patch, Cables, Mics, Parts, Manuals FS Message-ID: <8f2bd632-eb54-8649-2fe1-c3e1b576a396@gmail.com> Crystals, Phone patch, Cables, Mic, Parts, Manuals and more For Sale . I have a set of three crystals that are used to return the Kenwood Hybrid rigs to 10 meters, after they have had the original crystals changed to 11 meters. Specifically, they are HC-25 crystals for 33.50, 34.00, and 34.50 MHz. They are labeled as for the TS-820, but I think all of the hybrids use the same frequencies. These crystals are $12 each, or $35 for the set of three. . Kenwood PC-1 Phone Patch: The Kenwood PC-1 phone patch provides a connection between the transceiver and a telephone line. It is designed to provide high isolation between receiver input and transmitter output. Impedance levels (nominal): Line 600 ohm Receiver Input 8 ohms Speaker Output 8 ohms Microphone 50k ohms Microphone input and output is 4 pin. 6 x 2.25 x 5.75 inches. This one works fine and looks fine. - Only $25. . Linear Amp Switching Cables for Kenwood Rigs: This cable goes from a Kenwood transceiver to a linear amplifier to switch the amp from transmit to receive. One end has a DIN connector, as is used with most Kenwood rigs. The other end has an RCA phono plug, as used by most linear amplifiers. Before using this cable, please check the switching capabilities of your transceiver, and the requirements of your amplifier. Cable for switching the T/R relay Only $15. Cable as above, but with ALC line in addition to T/R switching. $20 . Hand Microphone with round 8 pin plug for Kenwood, Alinco, etc. This hand mic works great on most Kenwood rigs with the round 8 pin connector, such as the TS-440, TM-241, TM-2530, TW-4000, and others, including Alinco and ADI. It says "Electret Condenser Mic" on the back, and "Kenwood" on the front, with no model number. Basically, this mic functions like an MC-43, with a couple more features. It has the mic and PTT switch; it also has up/down switches on the top. There are four "extra" buttons labeled Call, VFO, MR, and PF. What these four buttons do depends on the rig. There is also a "Lock" switch on the back. Regardless if you use the four extra buttons or not, you still have a mic that works like an MC-43. This mic works fine, and looks like new. I am guessing it came with a rig, and was immediately put in the drawer, and never used. $30 . Kenwood MC-44 DM Touch tone Mic Has up/down buttons on top, 16 digit DTMF touch tone pad, Round 8 pin connector. Very nice condition. $40 . I still have a few parts left from parting out a TS-440. The following are presently available: Front panel PC board (includes digital display, S meter, push buttons, etc., including the metal work that it is all mounted to) $50 Front plastic panel $15 VFO encoder, including cable $25 I also have some other minor parts. Please let me know what you need, and we can go from there. . Original Manuals for Kenwood equipment For Sale: All manuals are in nice condition, for Kenwood equipment. All are Operating manuals unless otherwise specified. TH-21 2 m HT $8 TH-22/42 HT, cover stained $6 TH-215/315/415 HT for 2 m, 220 MHz, 440 MHz $10 TH-225 2 m HT, $12 TL-922 Linear Amplifier $20 TM-221/421 2 m or 440 MHz mobile $12 TM-241/441/541 mobile FM transceivers ...For 2 m, 440 MHz, & 1200 MHz $12 TM-261/461 2m or 440 MHz mobile $12 TM-621/721 Dual Bander $12 TM-V7A dual bander $10 TR-2400 2 m HT, $12 Service manual for TR-2600 2 m HT $12 TS-430 HF Transceiver $15 TS-450 "External Control" (not operating manual) $7 TS-570 S / D HF Transceiver $20 Service Manual for TS-120 S, Very Good Copy, in binder $15 TW-4000 dual bander mobile $15 Service manual for TW-4000 dual bander $20 TW-4100 dual band mobile $15 - These are original manuals only. . Original Manuals for Kenwood Accessories: All manuals are in very nice condition, for Kenwood accessories. All are original Kenwood manuals only. BC-2 Wall Charger $2 BC-5 DC to DC quick charger $2 DC-21 Dc-DC Converter $2 LF-30A Low Pass Filter $4 MC-30 & MC-35 hand microphones $4 MC-50 Desk Microphone $4 MS-1 mobile stand $3 PB-1, PB-2, PB-3, & PB-4 battery packs $2 PB-21 Battery Pack $2 PB-24 battery pack for TR-2400 $2 PB-25 H battery pack for TR-2500 $2 PS-6 power supply $5 PS-30 power supply $4 SC-8 / 8T Soft Case $2 SMC-24 speaker mic $2 SMC-25 speaker mic $2 SP-820 Speaker $2 VFO-230 Remote VFO $10 These are original manuals only. . Kenwood Operating Manuals in "Non English" Languages: All of the following manuals are not in the English language. They are the original Kenwood operating manual only. They look quite extensive and detailed, and are basically new, only being opened to observe that it is something I can not read. They are all original from Kenwood and are all $8 each. Kenwood TH-22 A Two Meter HT Spanish Version for the TH-22 A / 22 AT / 22E and TH-42 A / 42 AT / 42 E Kenwood TH-22 A Two Meter HT French Version for the TH-22 A / 22 AT / 22E and TH-42 A / 42 AT / 42 E Kenwood TM G-707 dual band transceiver Spanish version of the TM G-707 Operating Manual . I also have many other accessories available such as many different types of microphones, HTs, VHF and UHF rigs, HF and VHF/UHF antennas, connectors, miscellaneous accessories, etc. Just too many to list here. Please e-mail your requests. . Prices do not include shipping from Florida. Thanks. 73, Ken, W8EK Ken Simpson E-mail to W8EK at FLHam.net or W8EK at arrl.net Voice Phone (352) 732-8400 . . From gharmon at idworld.net Fri Feb 1 19:25:05 2019 From: gharmon at idworld.net (Gary H. Harmon, Jr.) Date: Fri, 1 Feb 2019 18:25:05 -0600 Subject: [Kenwood] HC-10 Clock Servicing Message-ID: <002401d4ba8d$bea9a150$3bfce3f0$@idworld.net> Anyone have experience servicing a HC-10 clock. I have two and the main display of one is brighter than the other. Thanks. Gary H. Harmon, Jr. - K5JWK - HAM Radio and ATARI Archaeologist 6003 Archwood San Antonio, TX 78239-1504 (210) 657-1549 (210) 884-6926 (210) 657-1549 gharmon at idworld.net "Retirement = Every day is a Saturday except Sunday" "Real radios glow in the dark" "Too many projects, not enough time" http://www.grissomroadcoc.org From manualman at juno.com Fri Feb 1 19:40:11 2019 From: manualman at juno.com (manualman at juno.com) Date: Fri, 1 Feb 2019 19:40:11 -0500 Subject: [Kenwood] HC-10 Clock Servicing Message-ID: For starters, make sure the AC input voltage settings are the same for both models. This thing is set up to be able to run on several different AC inputs. Pete, wa2cwa On Fri, 1 Feb 2019 18:25:05 -0600 "Gary H. Harmon, Jr." writes: > Anyone have experience servicing a HC-10 clock. I have two and the > main > display of one is brighter than the other. > Thanks. > Gary H. Harmon, Jr. - K5JWK - HAM Radio and ATARI Archaeologist > From bill.riches at verizon.net Sat Feb 2 07:30:40 2019 From: bill.riches at verizon.net (B Riches) Date: Sat, 2 Feb 2019 12:30:40 +0000 (UTC) Subject: [Kenwood] HC-10 Clock Servicing In-Reply-To: References: Message-ID: <587345446.2082411.1549110640979@mail.yahoo.com> I had one many years ago and a Company called RTO in the mid west repaired mine and did a good job.? I think they are still around.? Perhaps they can give you some info. 73, Bill, WA2DVUCape May On Friday, February 1, 2019, 7:42:19 PM EST, manualman at juno.com wrote: For starters, make sure the AC input voltage settings are the same for both models. This thing is set up to be able to run on several different AC inputs. Pete, wa2cwa On Fri, 1 Feb 2019 18:25:05 -0600 "Gary H. Harmon, Jr." writes: > Anyone have experience servicing a HC-10 clock.? I have two and the > main > display of one is brighter than the other. > Thanks. > Gary H. Harmon, Jr. - K5JWK - HAM Radio and ATARI Archaeologist > ______________________________________________________________ Kenwood mailing list Home: http://mailman.qth.net/mailman/listinfo/kenwood Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Kenwood at mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html From w3frg1 at gmail.com Sun Feb 3 11:46:03 2019 From: w3frg1 at gmail.com (Tom-W3FRG) Date: Sun, 3 Feb 2019 11:46:03 -0500 Subject: [Kenwood] AUTO Antenna TUNE Connectors Message-ID: This is the small rectangular OEM 6 pin connector (ELP-06V), female pins included, used for the Auto Tune Antenna function on the TS-50S, TS-480, TS-570, TS-590S/SG, TS-850S ACC4, TS-990S, TS-2000, TurboTuner, LDG K-OTT and many, many, more. Mating connectors (ELR-06V) and pins available for making cable extensions. Prices: 1 - 4 $7.25 each; 5 - 9 $6.75 each; 10 - 15 $6.25 each; 16 and up $5.75 each. Full details on QRZ Web site under W3FRG *Free Domestic Shipping* Accept PayPal, MO, Cash or Personal Check. Contact Tom: w3frg1 at gmail dot com From cemilton at aol.com Mon Feb 4 09:39:46 2019 From: cemilton at aol.com (cemilton at aol.com) Date: Mon, 4 Feb 2019 14:39:46 +0000 (UTC) Subject: [Kenwood] FOR SALE References: <540458691.2703434.1549291186655.ref@mail.yahoo.com> Message-ID: <540458691.2703434.1549291186655@mail.yahoo.com> GM to the list.?I have the following for sale.?1.? KB-1 knob for the TS-830S.? New in box.?? $402.? Kenwood TL-922 Service manual,???????????????$103.? Kenwood AT-50 automatic tuner.? Fits the TS-50.? With both short and long cables.? $404.? Voice module for the TS-440S.? Was removed from a working rig 3-years ago.? AFAIK, it is fine.? $25.5.? Handle with original screws for TS-440S.?? $56.? AT unit for the TS-440S.? Was removed from a working rig 3-years ago.? AFAIK, it is ok.?? $407.? Mobile mounting bracket for the TS-440S.? This is the bracket and hardware that the 440 is mounted to.? $10?I will sell items separately.? Prices shown DO NOT include postage.?If interested, contact me off the list.?Tnx es 73 de W4MILChuck? From cemilton at aol.com Mon Feb 4 09:57:59 2019 From: cemilton at aol.com (cemilton at aol.com) Date: Mon, 4 Feb 2019 14:57:59 +0000 (UTC) Subject: [Kenwood] Kenwood items just listed........... References: <1382996529.2717338.1549292279798.ref@mail.yahoo.com> Message-ID: <1382996529.2717338.1549292279798@mail.yahoo.com> I know not why, but my message with the Kenwood items for sale linked the numbering of the items (i.e. 1,2,3 etc)was the prices.? So read carefully and just remove the item number from the price.? Sorry for the inconvenience.?73Chuck W4MIL From mg.jacoby at verizon.net Mon Feb 11 18:04:54 2019 From: mg.jacoby at verizon.net (Mike Jacoby) Date: Mon, 11 Feb 2019 23:04:54 +0000 (UTC) Subject: [Kenwood] TS-940S for sale References: <1945060712.1967176.1549926294374.ref@mail.yahoo.com> Message-ID: <1945060712.1967176.1549926294374@mail.yahoo.com> Kenwood TS-940S, $550 plus shipping. This rig looks and works great; I am the original owner. (S/N 8010228) See Dec 2014 QST, p. 87 for a pic of the rig and me. With AT-940 antenna tuner and a YK-88C-1 500 Hz CW filter installed. Includes MC-60A base mic, original box, instruction and service manuals. 73, Mike? N3MA From holden7471 at msn.com Mon Feb 18 22:39:01 2019 From: holden7471 at msn.com (howard holden) Date: Tue, 19 Feb 2019 03:39:01 +0000 Subject: [Kenwood] Winter 2019 Classic Exchange Phone Message-ID: The Phone Classic Exchange will take place Sunday Feb 24 1300Z to Feb 25 0700Z and Tuesday Feb 26 1300Z to Feb 27 0700Z The CX is a no-pressure contest celebrating the older commercial and Home Brew equipment that was the pride and joy of ham shacks many decades ago. The object is to encourage restoration, operation and enjoyment of this older Classic equipment. You need not operate a Classic rig to participate in the CX. You may use any rig in the contest although new gear is a distinct scoring disadvantage as your multipliers are directly related to the age of the equipment you use! However, you can still work the "great ones" with modern equipment. There are Suggested CX Frequencies (+/- QRM) 160M 80M 40M 20M 15M 10M 6M 2M AM 1.890 3.860 7.270 14.280 21.400 29.000 50.400 144.300 SSB 1.920 3.840 7.250 14.260 21.380 28.600 50.125 144.200 Bonus Points for the Winter 2019 CX: Bonus #1: 500 Points for each dynamotor powered TX and RX that is qualified. Bonus #2: 500 Points for each Johnson transmitter, amplifier, SSB adapter, and VFO that is qualified. Bonus #3: 500 Points for each Knight transmitter, receiver, and VFO that is qualified. 2000 points max for each bonus per mode. For full details, rules, and logging submissions, visit the CX website: http://classicexchange.org/jan19/Winter_2019_CX_Rules.pdf Questions? Contact: Mark k3msb at arrl.net Ron k2rp at arrl.net (or you can contact me WB2AWQ at arrl.net)