From af5cc2 at gmail.com  Thu Jan  4 16:20:14 2018
From: af5cc2 at gmail.com (John Geiger)
Date: Thu, 4 Jan 2018 15:20:14 -0600
Subject: [Kenwood] FS: Kenwood TS2000 HF/VHF/UHF/satellite radio
Message-ID: <CAHC1P2-jJGBMitJ0-fbp=e0GqtBsk5K5xsR8hfaDx6BRuA1=aA@mail.gmail.com>

I have for sale a Kenwood TS2000 HF/VHF/UHF satellite transceiver.  Does
100 watts on HF, 6m  and 2m, and 50 watts on 70cm.  Has IF DSP for noise
reduction and IF filtering, also has TCXO installed, and CW memory keyer.
The internal TNC in this radio doesn't work so you cannot use it for remote
control by Sky Command.

Also, the radio took a little tumble a couple of months ago and one corner
of the bezel got banged up a little, and a couple of the buttons got pushed
in a little into the bezel but they still do operate.  The noise reduction
button is pushed in the furthest and I programmed the PF key to control
noise reduction.  I am including a hand mic with 4 programmable buttons on
it so you can use it to control some of these other functions.

The TS2000 has the DRU-3A voice recorder installed, which is a $119 value.
It also comes with a power cord, original box, and manual.

I am asking $550 for it plus any shipping that is needed.

73 John AF5CC

From af5cc2 at gmail.com  Thu Jan  4 16:30:09 2018
From: af5cc2 at gmail.com (John Geiger)
Date: Thu, 4 Jan 2018 15:30:09 -0600
Subject: [Kenwood] FS: Kenwood TS950S dual receive HF radio
Message-ID: <CAHC1P2-rUazfeUKKa55POaqXA91kUHtgP7=S88-RkhYExdL2YQ@mail.gmail.com>

I have for sale a Kenwood TS950S HF transceiver. Once Kenwood's top of the
line radio. It is rated at 150 watts out (does a little more on most bands)
and has 2 receivers for dual receive. It has a built in power supply, an
autotuner that will match about anything, and a built in CW keyer. Many
other receive functions like Slope Tuning for SSB and Variable Bandwidth
Tuning (both AF and IF) for CW.   The noise blanker takes out about any
type of noise I have seen.  It also has the DSP-10 DSP unit installed, and
comes with stock filtering-2.4khz filters at the second and third IF.

The rig is in excellent operating condition, with 1 issue and good physical
condition with a few small circle marks on the top of the case where
something else was setting on it. Also the fan cage on the rear of it has a
dent in it, but the fan still works fine. It comes with a hand mic, AC
power cord, and manual.

The operating issue is that sometimes, maybe once a week or so, the power
out will drop to zero. You turn the radio off, turn it back on, and it is
good to go.  Not sure what is causing this

This is a great radio and I really enjoy it but am trying to get set up for
remote operation and it doesn't seem to be possible with this radio.

I am asking $450 for it, plus any shipping-it is heavy.  I can take
paypal/check/MO.

You won't find another radio of this caliber at this price.

73 John AF5CC

From af5cc2 at gmail.com  Fri Jan  5 13:58:51 2018
From: af5cc2 at gmail.com (John Geiger)
Date: Fri, 5 Jan 2018 12:58:51 -0600
Subject: [Kenwood] CW filters for sale
Message-ID: <CAHC1P2-xJ7DkZJg2VXVkA9SSvmkoKYjwTUTZyOPg+361dv8Fig@mail.gmail.com>

I have for sale the following CW filters for the TS950/850/450/690/570 and
other Kenwood radios:

YK-88c-1 500 hz filter for the 2nd IF $70
YG-455C-1 500hz filter for the 3rd IF $85
YG-455CN-1 270hz filter for the 3rd IF $85

Prices include shipping in the US.  I can take paypal/check/MO.
These will NOT work in the TS480 series.


73 John AF5CC

From frank.woelfle at gmail.com  Wed Jan 10 18:18:06 2018
From: frank.woelfle at gmail.com (Frank Woelfle)
Date: Wed, 10 Jan 2018 23:18:06 +0000
Subject: [Kenwood] FS: Kenwood TS2000 HF/VHF/UHF/satellite radio
In-Reply-To: <CAHC1P2-jJGBMitJ0-fbp=e0GqtBsk5K5xsR8hfaDx6BRuA1=aA@mail.gmail.com>
References: <CAHC1P2-jJGBMitJ0-fbp=e0GqtBsk5K5xsR8hfaDx6BRuA1=aA@mail.gmail.com>
Message-ID: <CAD2sky13+GgRUSmpmroQOnBdZnsXnK8s57xbvfbLtSL-YGreDg@mail.gmail.com>

Hey John, did you sell this radio?

On Thu, Jan 4, 2018 at 2:21 PM John Geiger <af5cc2 at gmail.com> wrote:

> I have for sale a Kenwood TS2000 HF/VHF/UHF satellite transceiver.  Does
> 100 watts on HF, 6m  and 2m, and 50 watts on 70cm.  Has IF DSP for noise
> reduction and IF filtering, also has TCXO installed, and CW memory keyer.
> The internal TNC in this radio doesn't work so you cannot use it for remote
> control by Sky Command.
>
> Also, the radio took a little tumble a couple of months ago and one corner
> of the bezel got banged up a little, and a couple of the buttons got pushed
> in a little into the bezel but they still do operate.  The noise reduction
> button is pushed in the furthest and I programmed the PF key to control
> noise reduction.  I am including a hand mic with 4 programmable buttons on
> it so you can use it to control some of these other functions.
>
> The TS2000 has the DRU-3A voice recorder installed, which is a $119 value.
> It also comes with a power cord, original box, and manual.
>
> I am asking $550 for it plus any shipping that is needed.
>
> 73 John AF5CC
> ______________________________________________________________
> Kenwood mailing list
> Home: http://mailman.qth.net/mailman/listinfo/kenwood
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Kenwood at mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to frank.woelfle at gmail.com
>

From af5cc2 at gmail.com  Fri Jan 12 16:51:39 2018
From: af5cc2 at gmail.com (John Geiger)
Date: Fri, 12 Jan 2018 15:51:39 -0600
Subject: [Kenwood] FS: Rascal interface for Kenwood radios
Message-ID: <CAHC1P2-83jH4cDOcv+joxwj=9jqmOHVx-2E2deYU7YdgZvCOUw@mail.gmail.com>

I have for sale a Buxcomm Rascal sound card interface for Kenwood radios
with the 13 pin ACC jack on them.  It plugs into a serial port on the
computer and the sound card jacks.

I am asking $40 shipped for it and can take paypal/check/MO.

73 John AF5CC

From af5cc2 at gmail.com  Fri Jan 12 23:20:47 2018
From: af5cc2 at gmail.com (John Geiger)
Date: Sat, 13 Jan 2018 04:20:47 +0000
Subject: [Kenwood] FS: Some Kenwood plugs and cables
Message-ID: <CAHC1P2-VeMqsuGe1=oJXxxot3xNCyqc9LH7nRgkgvVnXhk=RfA@mail.gmail.com>

I have a couple of amplifier cables for Kenwood rigs, and a 13 pin DIN plug
for sale.

The 13 pin DIN plug comes in the accessory package for a TS2000.  It has 3
or 4 inch wires coming from each pin, which is much easier than soldering
wires to those pins.  The pack also had 3 spade fuses and a 1/4" stereo
plug with it.  The package in unopened and I am asking $15 shipped for them.

I also have for sale a cable with the 7 pin DIN on one end and phono plugs
on the other for ALC and relay control for an HF amplifier.  You could also
use the relay jack on it to key a transverter or other accessories.  This
will only key when on an HF band.  I am asking $14 shipped for it.

Lastly I have an amplifier cable for the VHF side of the TS2000 and maybe
other rigs.  It has the 8 pin DIN connector on 1 end, and then 2 cables
with phono plugs.  1 is for keying a 6 meter amplifier or accessory and the
other is for keying a 2 meter amp or transverter hooked to the 2 meter
antenna port.  I am asking $15 shipped for it.

I can take paypal/check/MO.

73 John AF5CC

From holden7471 at msn.com  Sat Jan 13 12:12:29 2018
From: holden7471 at msn.com (howard holden)
Date: Sat, 13 Jan 2018 17:12:29 +0000
Subject: [Kenwood] Winter 2018 CW Classic Exchange
Message-ID: <BL2PR06MB2290BA86DE68126424C00CD3C4140@BL2PR06MB2290.namprd06.prod.outlook.com>

The CW CX will run from 1300 UTC January 21 to 0800 UTC January 22, 2018
 (9 AM Eastern Time on Sunday to 3 AM Eastern Time Monday)
AND
 from 1300 UTC January 23, to 0800 UTC January 24, 2018
 (9 AM Eastern Time on Tuesday to 3 AM Eastern Time Wednesday)

Suggested Frequencies -- plus/minus QRM
Listen up and down 5 to 10 Kc for crystal controlled stations
CW     1.810 mc.     3.545 mc.     7.045 mc.     14.045 mc.     21.045 mc.     28.045 mc.     50.100 mc.     144.100 mc.

The CX is a no-pressure contest celebrating the older commercial and homebrew equipment that was the pride and joy of ham shacks many decades ago. The object is
to encourage restoration, operation and enjoyment of this older Classic equipment.

However, you need not operate a Classic rig to participate in the CX. YOU MAY USE ANY RIG in the contest although new gear is a distinct scoring disadvantage.
You can still work the "great ones" with modern equipment.

BONUSES
Up to 2,000 point bonus will be awarded to every CX participant who operates the same model rig as their Novice station.
Three QSOs are required.
One receiver and one transmitter may be counted and are worth 1,000 points each. Multiple version of the same piece of gear will not increase the bonus.

Up to 2,000 point bonus will be awarded to every CX participant who operates a transmitter with 4 tubes and/or less or a receiver with 6 tubes or less.
Three QSOs (each) are required.

Awards will be given in two classes: 1. Three or fewer receiver-transmitter pairs 2. Four or more receiver-transmitter pairs.

Send logs, comments, anecdotes, pictures, etc. to

e-mail: Ron K2RP       k2rp at arrl.net<mailto:k2rp at arrl.net>

E-MAIL IS (REALLY) PREFERRED BUT NOT ABSOLUTELY NECESSARY

 Or by mail to:
 K2RP
 659 Shanas Lane
 Encinitas, CA 92024

 Full details at: http://classicexchange.org/sep17/sep17ann.html

Questions? email me!

CU on the air for CX!

73, Howie WB2AWQ/7

From af5cc2 at gmail.com  Tue Jan 16 12:01:07 2018
From: af5cc2 at gmail.com (John Geiger)
Date: Tue, 16 Jan 2018 11:01:07 -0600
Subject: [Kenwood] FS: Kenwood YG455C-1 CW filter-$65 shipped
Message-ID: <CAHC1P2-ZYbKYV_Qybv=Cswz1i10n5azFPSpSbNKds30YYzySQw@mail.gmail.com>

I have for sale a Kenwood YG455C-1 500hz CW filter for the Kenwood
TS930/940/950/850/450/690/140/680 series of radios.  It will not work in
the TS570/TS480/TS50 series.

It works fine and is in good condition.  I am asking $65 shipped for it.  I
can take paypal/check/MO.


73 John AF5CC

From glwolfen3ics at verizon.net  Wed Jan 17 15:03:00 2018
From: glwolfen3ics at verizon.net (Gary Wolfe)
Date: Wed, 17 Jan 2018 15:03:00 -0500
Subject: [Kenwood] ts-950s
Message-ID: <B4C51A961C5842D4B6DBF749867B8693@GLW>

     Hello, I own a K-wood TS-950S, ser# 0110242. The issue I have is the memory battery (BA1) on the digital board was almost dead, so when the radio is turned on the display shows 14.0000 and when installing a battery source of 3volts  and holding the A=B button while turning the radio back on the same results: 14.000 and then the digits disappear and UV in cw is sounded from the radio.  Has any body else had this problem?  Any help would be appreciated   Thank You, Gary N3ICS

From kenw8ek at gmail.com  Wed Jan 24 10:33:16 2018
From: kenw8ek at gmail.com (Ken, W8EK)
Date: Wed, 24 Jan 2018 10:33:16 -0500
Subject: [Kenwood] Kenwood TS-820 S HF Transceiver FS
Message-ID: <d226372f-db93-49ac-039f-c91b7ace027e@gmail.com>


Kenwood TS-820 S HF Transceiver For Sale:
-
The TS-820 S is an hybrid HF transceiver.  It was
the standard transceiver a few years ago.  It is
still a good performer, but not spectacular.
No DSP!
-
This one is a tech special.  I think the problem is
fairly minor.  There is no 14 V DC, which means that
there is no 5 V DC, since the 5 V is derived from the
14 V.  This means that all of the low voltage sections
do not function.  The higher voltages are all present.
It appears that the problem with the 14 V DC is the
diode bridge.  Likely replacing the diodes will solve
the problem.  However my eye sight is not good
enough to do that, so my loss, your gain.
-
The cosmetics on the rig are extremely good.  So
even if you do not repair it, you could use it for
parts, or to make one that is cosmetically challenged
look nice again.
-
With power cord for only $75 plus shipping from Florida.
-
Thanks. 73,
Ken Simpson, W8EK
Phone  (352) 732-8400
.


From af5cc2 at gmail.com  Fri Jan 26 11:23:13 2018
From: af5cc2 at gmail.com (John Geiger)
Date: Fri, 26 Jan 2018 10:23:13 -0600
Subject: [Kenwood] WTB: Kenwood ARCP 2000 computer control software for
	TS2000
Message-ID: <CAHC1P2_jjjZm_2iwNjWWdWQoTqsRrYJezZ1j9mJzXK2Hx74-7A@mail.gmail.com>

I wonder if anyone might have the Kenwood ARCP-2000 for the TS2000 that
they are not using and might be willing to sell. I had a new copy of it a
few months ago and sold it, thinking I wasn't going to need it. Wrong
thought-I am now trying to get my TS2000 set up for remote control over the
internet and I need this software for it.

If you have the software to sell, please let me know the price shipped to
Lawton, OK ZIP 73507



73 John AF5CC

From af5cc2 at gmail.com  Tue Jan 30 12:40:43 2018
From: af5cc2 at gmail.com (John Geiger)
Date: Tue, 30 Jan 2018 11:40:43 -0600
Subject: [Kenwood] R and L has DRU-2 at a good price
Message-ID: <CAHC1P29+g=bb6_Gy+TSct7evwZZ9HtNV7S2qet-xk+KOxq4pEg@mail.gmail.com>

Not mine, but seems like a good price if you are looking for one for your
TS850 or TS950SDX.  They say it works on the TS950S and SD but that is
incorrect, I believe.

Here is the listing for it:

http://www.randl.com/shop/catalog/usedq.php?id=11888&model=DRU2