[Kenwood] Kenwood Remote VFO, filters and other misc parts FS

[Ken, W8EK]

Kenwood VFO-820, Crystal Filters, plus other
miscellaneous parts For Sale:


Kenwood VFO-820 remote VFO:

The Kenwood VFO-820 was designed to work with
the TS-820 HF transceiver, but will also work with
the TS-520, and possibly others.

This remote VFO permits one to transceive from the
VFO or to work split with it. An RIT is also included.

This one has a smooth dial, and functions well.
Cosmetically, it is in extremely good condition.
As with most of these VFOs, it was missing the cable
to connect the VFO to the transceiver. I have a cable
that I used to test it that can have its stripped and
tinned ends put into the sockets on the VFO and rig.
There is no plug on either end.

Paper work is included for $100.


Kenwood Crystal Filters:

Kenwood YK-88 S 1 Crystal Filter:
This filter is 2400 Hz wide.
This is a "plug in filter" as opposed to the type that must
be soldered in. It is used in rigs such as the TS-450, TS-570,
TS-690, TS-850, TS-930, TS-940, TS-950, and others.
It is for the 8.83 MHz IF.
It works fine and looks like new.
Paperwork is included for $75.

Kenwood YK-88 SN
This is the "solder in" type filter that is used in the TS-130,
TS-430, TS-440, TS-530, TS-830, R-5000, and many others.
It is 1800 Hz wide making it ideal for narrow SSB, but also
for digital modes. It works fine and looks like new. $70


Kenwood MC-85 Desk Mic "Tech Special":

It looks like the silent key was working on repair of this when
he passed. All parts appear to be present, plus the addition
of a couple extra up/down switches. $45


Kenwood MC-85 Deluxe Desk Microphone Parts:

The Kenwood MC-85 will take up to three mic cords,
i.e. it is capable of being used on three rigs.

Extra cable to go from MC-85 to a Kenwood 4 pin connector,
as is used on the TS-520, TS-820, TS-120, TS-130, etc. $20


DC Power Cable:
This is the heavy duty power cable as used on most of the
Kenwood HF rigs, plus also many Icom, Alinco, and others.
It has the 6 pin molex connector, with four pins used - two
for plus and two for ground.  It looks good, and of course
works fine. $22


Linear Amp Switching Cables for Kenwood Rigs:

This cable goes from a Kenwood transceiver to a linear
amplifier to switch the amp from transmit to receive.

One end has a DIN connector, as is used with most Kenwood
rigs. The other end has an RCA phono plug, as used by most
linear amplifiers.

Before using this cable, please check the switching
capabilities of your transceiver, and the requirements
of your amplifier.

Cable for switching the T/R relay. Only $15.

Cable as above, but with ALC line in addition to T/R switching.
$22


Kenwood "Extension Feet":

This is a set of two feet that are often used on
various Kenwood rigs to raise the front by about
1/2 inch to give a rig, speaker, remote VFO, etc.
the tilt that makes it easier to read.

This is a complete set of two front feet, with the
needed hardware. I have a couple sets available for
$15 each.


Heath "SB Line" Extension Feet:

This is a set of all four feet as used on most of the
Heath SB line included transceivers, speakers, amplifiers,
etc.

It consists of the two shorter feet for the back, and two
taller feet for the front, plus hardware for all. $20


Code Key and Cables for code keys and paddles:

Cable for straight key
About 3 feet long, with a mono 1/8 inch (3.5 mm) phone plug on it,
as used with a straight key. $5
As above, but 1/4 inch plug. $5

Cable for paddles
About 3 feet long, with a 1/8 inch (3.5 mm) stereo connector on the
end, as used by most rigs for paddles. $8
As above, but 1/4 inch plug. $8
As above, but 1/4 inch plug and coiled cord. $10


I also have many other accessories of many different brands
available.
Just too many to list here. Please e-mail your requests.


Prices do not include shipping from Florida.

Thanks.

73,

Ken, W8EK

Ken Simpson
E-mail to W8EK at FLHam.net or W8EK at arrl.net
Voice Phone (352) 732-8400