[Kenwood] HF Rig, PSs, Dummy Load, Wattmeter, Mics, and much more FS

[Ken Simpson, W8EK]

HF Rig, Power Supplies, Dummy Load, Station Console,
Wattmeters/SWR Bridges, Coax Antenna Switch,
Microphones, HT Speaker Mics, DTMF Touch Tone
Microphones, Accessories for Kenwood HTs, original
Kenwood Manuals, and other Kenwood items For Sale:


Kenwood TS-130 HF rig, and PS-30 Power Supply:

Kenwood TS-130 HF SSB / CW transceiver
This rig covers 80 thru 10 meters, including the WARC bands.
It has about 100 watts out, with slightly lower on 12 and 10
meters. Of course it has IF shift, speech processor, and other
features. It is all solid state.
This one works fine, and looks fine. With paper work for $350.

Kenwood PS-30, 20 amp (at 13 V DC) power supply:
This power supply will furnish up to 20 amps at 13 V DC to power
most 100 W output HF transceivers. It also has auxiliary
terminals on the back to power an additional rig, such as a
2 m rig. The main connector is the 6 pin molex connector
that will match most Kenwood, Icom, and Alinco HF radios,
as well as some Yaesu.
This particular unit works 100% and looks very nice.
Paper work included for $90.

Buy both of the above for $425.


Astron RS-20A Power Supply:

The RS-20A is a DC Power Supply producing 13.8 V DC (internally
adjustable from 11 to 15 V DC) at up to 16 amps continuous and
20 amps ICS. The RS-20 features crowbar over voltage protection
and fold-back current limiting to protect your equipment.

This particular supply works fine, and looks very close to new.
I do not find a scratch on it.

With paper work for $60.


Heath HN-31 "Cantenna" RF Dummy Load

This is the traditional Heath dummy load that will handle a
kilowatt. It has a derating curve both printed in the manual
and on the can.

It is in good shape both electrically and cosmetically. The
cantenna has no rust, dents or dings.

I can ship it either with or without oil. The cost to purchase
is the same, but of course the shipping will be higher with
the oil.

Paper work is included for $40.


Heath SB-634 Station Console:

The Heathkit SB-634 station console is a multifunction unit.
It contains a 24 hour digital clock (6 large digits, including
seconds), 10 minute interval timer (3 digits -- minutes and
seconds), phone patch and an SWR/Power meter. The large
wattmeter reads either 200 watts or 2000 watts full scale,
in addition to SWR. It matches the Heath SB series of equipment
(Heath green), and is powered by 115 V AC.

This unit works on all of its functions. It looks extremely
nice. I can not find a scratch on it, but there is very slight
(and I emphasize very slight) wear on the 2000 watt push button.

With paper work for $150.


Heath HM-2140 A, dual meter Wattmeter / SWR Bridge:

The HM-2140 A uses two separate meters to measure power and
SWR (forward and reflected power). It will measure either
average power, or peak power (PEP) with a 9 volt battery.
Power ranges are 200 and 2000 watts. Frequency range is
from 160 thru 10 meters. It has a remote sensor, which
permits the meter to be separated from the coax connection
by up to 3 feet. This is the "A" model of this meter, which
is the Heath Brown color (not the green), and has more features.

More details can be found at
http://www.radiomuseum.org/r/heath_wattmeter_hm_2140a_hm2140.html

This particular unit works fine, and looks very close to new.
With paper work for $100.


HF and VHF SWR Bridges:

All of these cover from 3 to 150 MHz, covering HF, 6 meters,
and 2 meters. SO-239 connectors.

Quement SWB-2
This unit features two separate meters -- one for reading
forward power and another for reading SWR. This permits one
to easily monitor both the power going out, and the SWR on
the antenna at the same time.
It works fine and looks great. With paper work for $37.

Carter Craft 90-300
Single Meter SWR Bridge / Field Strength Meter
This one works fine. I am 99% certain it has not been used,
except for my testing it.
In its original box with original instructions and little
field strength antenna. $30

Royce 2-100 Single Meter SWR Bridge / Field Strength Meter
This one works fine, and looks extremely nice. I do not see
any scratches on it, but it does have a previous owners name
on it. In its original box with original instructions. $28


MFJ "Strip Line" Coaxial antenna switch:

This antenna switch is in a heavy diecast housing
that utilizes "stripline" construction to keep the impedance
very close to 50 ohms. This means it permits good operation
at higher frequencies up to 500 MHz, and gives over 50 db
isolation. Unused antennas are grounded, with an additional
position to ground all antennas. SO-239 connectors.

MFJ 1702 B Coax Switch
Switches 2 antennas. This one works 100% and looks great
also. $24


Deluxe Desk Microphone w/ Kenwood 8 pin connector:

This is a great looking and great performing low impedance
desk mic. It has a quality Shure 600 ohm cartridge in it
(the cartridge alone is over $40 new), with a very nice
black die case base and neck, with a chrome grill. It
looks somewhat like a Shure 444, but no plastic on this
one -- all metal!

This one looks like new, and works the same. It has a
long (approx 6 foot) cord, with a round 8 pin connector
for Kenwood. $75


Astatic Model 810-6 Gooseneck Microphone:

This mic is on a 12 inch gooseneck. The mic is a brushed
metal about 5 1/4 inches long, and is actually part of the
gooseneck. The cable goes thru the gooseneck. This has a
2 conductor shielded cable, so it is a quality balanced
microphone with about a 4000 ohm impedance. The gooseneck
terminates in a standard 5/8 inch threaded connector.

This one works fine and looks good. $45


Kenwood Hand Microphone with round 8 pin plug:

This hand mic works great on most Kenwood rigs with the
round 8 pin connector, such as the TS-430, TS-440, TS-570,
TM-241, TM-2530, TW-4000, and others.
It only says "Electret Condenser Mic" on it, with no
model number.

Basically, this mic is like an MC-43, only with a couple
more features. Of course it has the mic and PTT switch;
it also has up/down switches on the top. There are four
"extra" buttons labeled Call, VFO, MR, and PF. What these
four buttons do depends on the rig that it is attached to.
They will function on some rigs, and are completely useless
on others. There is also a "Lock" switch on the back.

Regardless if you use the four extra buttons or not, you
still have a mic that works like an MC-43.

This mic works fine, and looks like new. I am guessing it
came with a rig, and was immediately put in the drawer. $30


Speaker Microphones:

All of these have the 3.5 mm and 2.5 mm plugs on them,
as used by Kenwood, Icom, Alinco, Radio Shack, some Yaesu,
and other HTs.

Azden SDX-316
This is the rounder style speaker mic that fits nicely in
the palm of your hand. $ 20

Pryme Speaker Microphone
It works fine and look line new. $20

MFJ-287 Speaker Microphone
This fits the TH-21/31/41 series HTs, TH-205, TH-215, TH-415,
as well as others. It has a 3 conductor 3.5 mm plug and a 2
conductor 2.5 mm plug.
It works fine, and looks close to new. $15


DTMF Touch Tone Microphones:

CES 610 L DTMF Touch Tone Mic
Can manually dial a number, or automatically store it in
the mic, and "speed dial". 12 digit touch tone pad on the
front. 8 pin modular plug (like computer LAN).
Looks to be new. $38

KDK Model TM-2 DTMF Mic
With touch tone pad and up-down switches. It presently
has a round 8 pin connector wired for Kenwood.
Nice condition. $40

Johnson 250-0761-010 / CES 655 L DTMF Mic
It has a 12 digit pad on the front, and is a rugged mic.
Presently with 4 pin plug. Looks to be unused. $38

Yaesu YM-22 DTMF Condenser Microphone
This mic has a 16 digit touch tone (DTMF) pad on the front.
There are up and down buttons on the top, in addition to
the PTT switch.
Stripped and tinned ends. Great condition. $40


Cables for Heil (and other) Microphones:

Heil CC-1 XLR 4
3 pin XLR Male to 4 pin XLR Female $25

3 pin XLR to stripped and tinned ends
About 10 feet of quality rubber covered mic cable with a 3 pin
XLR connector on one end, and nothing on the other end. Ideal
to add your own connector. Can be used with the CC-1 XLR-4
above. $20

Heil round 8 pin connector to 8 pin modular connector for Icom
Not positive of the number, but it might be HSTA-IM or HSTA-706
$15


Microphone Stands and holders:

Microphone Stands:

Regular round desk stand
Round 6 inch diameter heavy black / dark grey base, with
a 3 inch chrome tube coming up from the middle.
Standard 5/8 inch threaded. $15

Microphone holders:

Electro Voice Mic Holder
Gray colored EV, designed to hold 5/8 to 3/4 inch diameter mics,
and go into a stand with standard 5/8 inch threads. $5

Chrome Mic holder
Similar to EV holder, but chrome metal with a green felt on the
inside to protect the mic. For 1/2 inch to 5/8 inch diameter
microphones. Standard 5/8 inch threads. $5


Cables for CW keyers and keys:

Cable for paddles
About 3 feet long, and with a 1/8 inch (3.5 mm) stereo
connector on the end, like used by most rigs. $8
As above, but 1/4 inch plug. $8
As above, with 1/4 inch GOLD plated plug. $15

Cable for straight key
About 3 feet long, with a mono 1/8 inch (3.5 mm) phone
plug on it, as used with a straight key. $5
As above, but 1/4 inch plug. $5
Vintage cotton covered cord, with brass PL-55-A
     (1/4 inch) plug (probably from WW2) $10


Accessories for Kenwood TH-205, TH-215, TH-225, TH-415,
and other HTs in this series:

Original Kenwood Rubber Duck antenna from TH-215. $10

Kenwood BC-2 Charger for PB-2 batteries. $12

MFJ-287 Speaker Microphone
Fits same HTs as the MFJ 286 above, but is a smaller more
compact speaker mic. It works fine, and looks close to new. $15

Kenwood Wrist Strap for TH-215, plus many other HTs. $4

BNC to PL-259 antenna adapter $5


Accessories for the Kenwood TH-21 / 31 / 41 series HTs:

Original Operating manual for TH-21 HT for 2 meters $8

Kenwood BH-3 belt clip and hardware for Kenwood TH-21/31/41
series HTs. $8

MFJ-287 Speaker Microphone
Fits same HTs as the MFJ 286 above, but is a smaller more
compact speaker mic. It works fine, and looks close to new. $15

Kenwood W09-0315 charger
This charger is used to charge the larger PB-21 H batteries
for the TH-21 series, and also on other Kenwood radios.
It produces 10.5 V DC at 42 ma, with a standard 2.1 mm
coaxial connector. $12

Kenwood Rubber duck antenna for the TH-21 HT
Shorter "Stubby Duck" from Kenwood. $20


Operator's Manual for Kenwood (Trio) TS-440 S:

This is a quality reproduction with a "comb" binding
that has been done by one of the professional reproduction
houses. W7FG I think.

This one has a plastic protector on the front, and is
in very nice condition. It includes schematic diagrams.
$18


Original Manuals for Kenwood equipment:
New ones have been added.

All manuals are in very nice condition, for Kenwood equipment.
All are original manuals only.

Operating manual for TM-2570/2550/2530 2 m xcvr $15
Operating manual for TW-4000 dual bander $15
Service manual for TW-4000 dual bander $20
Operating manual for TW-4100 dual bander $15
Operating manual for TH-21 HT for 2 m $8
Operating manual for TH-225, 2 m HT $12
Operating manual for TM-221/421 mobile $15
Operating manual for TH-241/441/541 mobile FM transceivers
...For 2 m, 440 MHz, & 1200 MHz. $12
Operating manual for TR-2400, 2 m HT $12
Service manual for TR-2600, 2 m HT $12
Operating manual for TR-7400, 2 m xcvr $8

Kenwood TM G-707 operating manual in Spanish:
Spanish version of the Operating Manual
for the TM G-707 dual band transceiver. New $10
All other manuals are English.

LF-30A Low Pass Filter $5
MC-30 & MC-35 hand microphones $5
MC-85 desk microphone $4
PB-1, PB-2, PB-3, & PB-4 battery packs $3
PS-6 power supply $6
SMC-24 speaker mic $4
SMC-25 speaker mic $4
SP-430 speaker $2
SP-820 Speaker $2

These are original Kenwood manuals only.


HT Belt Clips and Wrist Straps:

Belt Clips:
All include the hardware with the belt clip and are $8 each.
Kenwood BH-3 for Kenwood TH-21 / 31 / 41 series HTs
Motorola
Yaesu FT-207

Wrist Straps for various HTs - $4 each
Kenwood TH-215 / 225 / 415, TR-2500, etc.
Kenwood TR-2400
Yaesu FT-209


I also have many other accessories available such as many
different types of microphones, HTs, HF, VHF and UHF rigs, HF
and VHF/UHF antennas, and many miscellaneous accessories.
Just too many to list here. Please e-mail your requests.


Prices do not include shipping from Florida.

Thanks.

73,

Ken, W8EK

Ken Simpson
E-mail to W8EK at FLHam.net or W8EK at arrl.net
Voice Phone (352) 732-8400