[ICOM] 765 freq problem

[Marc & Tricia Niebergall]

Tnx.

Marc
On Feb 26, 2015 9:28 AM, "D. Jones" <djoneses at verizon.net> wrote:

> Mouser has the Sprague GKG10015 in stock for 60 cents each.  Comparing
> specs with the GKG10024 it seems these should work although they are 2.3 mm
> taller. I don't know if that is an issue.  The Mouser part number is:
> 659-GKG10015.
>
> David
>
> <div>-------- Original message --------</div><div>From: Marc & Tricia
> Niebergall <mtniebs at gmail.com> </div><div>Date:02/26/2015  10:52 AM
> (GMT-05:00) </div><div>To: ICOM Reflector <icom at mailman.qth.net>
> </div><div>Subject: Re: [ICOM] 765 freq problem </div><div>
> </div>Rich,
>
> Thanks for the additional info. It seems that the part numbers are pretty
> scarce, so I would welcome any new info regarding availability of ceramic
> trimmers.
>
> Marc
> On Feb 26, 2015 7:42 AM, "Rich Dailey" <redailey1 at gmail.com> wrote:
>
> > I'm the author of that page. I need to mention that I'm not sure of the
> > availablility of the replacement trimmers that are mentioned in the
> > article. If someone has a good link to a supplier of substitutes, I'll
> > update the page to add those links. Been a lot of years.
> >
> > Also, I'll throw in that I recall having one on the bench that had a
> > sililar drift situation. I replaced the trimmers, AND
> > 10uf bypass caps coming off a 5 volt regulator. They were pulling hard on
> > that supply voltage. Seems
> > it was on the board under the power supply, on a long, shared heat sink
> > with other regulators. Like I said,
> > it's been many years, my brain is foggy, but that's what I remember.
> >
> > Rich, N8UX
> >
> > On Thu, Feb 26, 2015 at 4:57 AM, rrocket88 at netzero.net <
> > rrocket88 at netzero.net> wrote:
> >
> > > here is an old descriptive i've had filed away, was going to perform
> but
> > > health went south  good luck K4IMZ
> > >
> > > http://home.windstream.net/ferncity/icom.htm
> > >
> > >
> > ----
> > Your Moderator: Dick Flanagan K7VC: icom-owner at mailman.qth.net
> > Icom Users Net: Sundays, 1700Z, 14.316 MHz
> > Icom FAQ: http://www.qsl.net/icom/
> > To support QSL/QTH.net: http://www.qsl.net/donate.html
> >
> ----
> Your Moderator: Dick Flanagan K7VC: icom-owner at mailman.qth.net
> Icom Users Net: Sundays, 1700Z, 14.316 MHz
> Icom FAQ: http://www.qsl.net/icom/
> To support QSL/QTH.net: http://www.qsl.net/donate.html
> ----
> Your Moderator: Dick Flanagan K7VC: icom-owner at mailman.qth.net
> Icom Users Net: Sundays, 1700Z, 14.316 MHz
> Icom FAQ: http://www.qsl.net/icom/
> To support QSL/QTH.net: http://www.qsl.net/donate.html