[ICOM] 2 m rig, PL encoder, Chargers, Manuals, Spkr Mics, and more FS

[Ken Simpson, W8EK]

2 meter FM transceiver, PL Tone encoder, Chargers, Manuals,
Speaker Microphones, DTMF Touch Tone Microphones and other
Miscellaneous For Sale:


Icom IC-281 H, 2 meter transceiver with 440 MHz receive

The Icom IC-281H 2 meter mobile FM transceiver boasts 50
watts output plus 440 band receive (440-450 MHz) for full
duplex crossband operation. Other features include 60
regular memories, 10 scratch pad memories, 14 auto dialer
memories, built-in pager and code squelch functions and
auto memory channel advance. The IC-281H is packet ready.
A data jack is available for direct TNC connection,
supporting speeds up to 9600 baud. It features a huge
heat sink. Requires 10.5 amps at 13 VDC.

Features
     * 440 MHz Band Receive
     * Tone Scan
     * 60 Memories
     * 10 Scratch Pad Memories
     * Scanning
     * Call Channel
     * 50/10/5 Watts Output
     * Auto Power Off
     * Priority Watch

This one works 100% and looks extremely nice.
With DTMF Mic, tone encoder, mobile bracket, power cord,
and paper work for $150.


SubAudible Tone (CTCSS or PL) Encoder:

This unit is designed to add subaudible tones (sometimes
called PL tones or CTCSS) to a rig that does not have them
internally. This is usually used on some of the older 2
meter FM or 440 MHz FM rigs produced before the tones were
included in the rig.

This particular unit can be used on most any rig, although
it came from an Icom IC-22 S, and I think was also used with
an Icom IC-230. It has a 9 pin plug on it that looks like
the base of a miniature 9 pin tube. This was the type of
socket used on these Icom rigs, but it could be changed.

This unit has a switch for 6 different tone on the front panel.
Each of the tones are internally adjustable. It is presently
set up for 71.9, 74.4, 94.8, 100, 123, and 179.9 Hz tones,
although they could be changed. It is housed in a black box
about 6.2 W, 2 H, X 4 inches deep.

This unit works fine. $35


Icom Battery Chargers:

Icom BC-127 A, Battery Charger for Icom IC-Q7A Dual Band HT:
This charger charges two AA NiCads (or NiMH) for the
IC-Q7 A Dual band HT, and Icom R-2 receiver, and probably
others.
This appears to be new, unused, still in its bag.
Icom lists them at $21. Buy this one for $12.

Icom BC-110 A / BC-167 Wall Wort Charger:
It produces 12 V DC at 200 ma.
I am not sure of all the units that use this charger.  I know
it is used by many of the aircraft HTs, and also to charge the
R-10, T2H, T7H, T70, T80AD, T90A, T91A, T92AD, W32A, and I am
sure others.  Apparently it is also known as a BC-167 in
addition to BC-110 A.  This is NOT one of the switching units,
so you will not have RFI from this one.
This one works fine and appears very close to new.
Icom charges almost $40 for this.  Buy this one for $15.


Other Wall Wart Power supplies:

All are standard "non-switching" types, with no noise like
the switching types have.

AEA AC-1 "Wall Wart" Power Supply
This "Wall wart" power supply will supply 12 V DC at
up to 1 amp.
It can be used with the AEA PK-232, PK-88 or others.
This unit has a 2.1 mm plug, with the center positive,
so it can be used on many different things that require
12 V DC at up to an amp, such as keyers, antenna tuners,
etc. $14

MFJ 1312 Wall Wart power supply
This unit provides 12 V DC at 500 ma It has a small 2.5
mm male plug, and is often used for keyers, lighting tuner
lights, and other small misc jobs where 12 V DC at low
current is needed. $10

Yaesu NC-18 B Charger
Provides 14.5 V DC at 50 ma to charge many different HTs,
including the Yaesu FT-411, FT-811, FT-911, FT-23, FT-209,
FT-415, FT-410, FT-470, FT-727, FT-530, FT-703, and more.
Small 2.5 mm male plug. $10


Icom DC adapter and batteries:

Icom DC-25
This is a pack that is used on the Icom µ2AT, Icom µ4AT, and
on other HTs that use the BP-20, BP-21, BP-22, BP-23 and BP-24
battery packs.  It takes 13 V DC (such as from a cigarette
lighter), and converts it to the 9.4 V DC voltage needed for
the HT.  It is used in place of a battery.  This one works
fine and looks fine.  $18

Icom BP-21 and Icom BP-22
Neither of these battery packs hold a charge and are sold
for rebuilding, for using the case, etc. $7 each


ORIGINAL Icom operating manuals:

Please note that all of these are original Icom manuals
and are not copies. All are in very good condition.
These are original manuals only.

BC-30 Desk Charger $5
BC-35 Desk Charger $7
BP-2, BP-3, BP-4, BP-5 battery packs $3
BP-21, BP-22, BP-23, and BP-24 Batteries $3
DC-1 DC pack for IC-2 AT series HTs $4
HM-8 Hand Microphone, w/schematic $5
IC-22 S, 2 m FM transceiver $12
IC-28 H, 2 m FM transceiver $12
IC-3 PA Power supply / speaker $10
UT-16 Voice Synthesizer $5

These are original manuals only.


Several HT Speaker Microphone:

Azden SDX-316 Speaker Microphone
Although it has an Azden name plate, it will also work
with Icom, some Yaesu, and Alinco that need 3.5 mm and
2.5 mm plugs.
This is the rounder style speaker mic that fits nicely in
the palm of your hand. $18

Speaker-mic for Yaesu (Vertex) VX-6 / VX-7 / VX-8
This speaker mic has a 4 conductor 3.5 mm connector,
with the threads as used by the VX-6 / VX-7/ VX-8.
Looks to be unused. $15

MFJ 286 Speaker Microphone
This was used on a Kenwood TH-225 HT, but it also fits the
TH-21/31/41 series HTs, TH-205, TH-215, TH-415, as well as
others. It has a 3 conductor 3.5 mm plug and a 2 conductor
2.5 mm plug. It works fine. $12

MFJ-287 Speaker Microphone
Fits same HTs as the MFJ 286 above, but is a smaller more
compact speaker mic. It works fine, and looks close to new. $15


DTMF Touch Tone Microphones:

CES 610 L DTMF Touch Tone Mic
Can manually dial a number, or automatically store it in
the mic, and "speed dial". 12 digit touch tone pad on the
front. 8 pin modular plug (like computer LAN).
Looks to be new. $38

KDK DM TT-1 DTMF Touch Tone Mic
This mic has a 12 digit touch tone pad on it, with a
switch to turn the pad on and off. With 4 pin plug.
It works fine, and looks great. $35

KDK Model TM-2 DTMF Mic
With touch tone pad and up-down switches. It presently
has a round 8 pin connector wired for Kenwood.
Nice condition. $40

Johnson 250-0761-010 / CES 655 L DTMF Mic
It has a 12 digit pad on the front, and is a rugged mic.
Presently with 4 pin plug. Looks to be unused. $38


Coax connectors and adapters:

Prices are per connector. Several of each are available.
It looks like these have not been used.

"N" Connector - Double Male $8

BNC male for coax cable
standard type $2
crimp on type $3

Chassis mount BNC female
square mount (uses 4 screws) $3
screw in type $3

BNC "T" - two female and one male $3

Antenna adapter to fit the BNC connector on the HT
and provide an SO-239 connector that will permit
a PL-259 to be attached. (BNC male to UHF female) $5

UHF Male (PL-259) to BNC female (opposite of above) $5

UHF double female "Barrel connector" (two SO-239 together) $3

UHF "Bulkhead Connector" - Double female, as above, but for
mounting thru a window, siding, etc. about 3 inches long $6

UHF double male connector (two PL-259's together) $3

UHF "T" connector with two female (SO-239) and one male
(PL-259) connection $5


I also have many other accessories available such as many
different types of microphones, HTs, HF, VHF and UHF rigs, HF
and VHF/UHF antennas, etc.
Just too many to list here. Please e-mail your requests.


Prices do not include shipping from Florida.

Thanks.

73,

Ken, W8EK

Ken Simpson
E-mail to W8EK at FLHam.net or W8EK at arrl.net
Voice Phone (352) 732-8400