[ICOM] 706 And Tigertronics?

gfiber at comcast.net gfiber at comcast.net
Fri Oct 20 16:27:12 EDT 2006


Ya there are some pins on the MKIIG used for different things than on the original one was the VHF / UHF PTT line. 

If you have questions do ask. I spent a lot of time while I worked at Icom helping callers connect thse things together via telephone.

Gary K8IZ
 -------------- Original message ----------------------
From: "Jay" <ad5pe at sbcglobal.net>
> I was aware of the classic not having UHF, but didn't think that would make
> the connector different.  Thanks for the link - I'll check out the manual.
> 
> Jay
> AD5PE 
> 
> -----Original Message-----
> From: icom-bounces at mailman.qth.net [mailto:icom-bounces at mailman.qth.net] On
> Behalf Of gfiber at comcast.net
> Sent: Friday, October 20, 2006 10:44
> To: ICOM Reflector
> Subject: Re: [ICOM] 706 And Tigertronics?
> 
> There are some differences. The MKIIG has UHF PTT capability so far as I
> remember where the original 706 did not. It would be best to download the
> original 706 manual so you can verify the connections. Likely it will work
> fine.
> 
> http://www.icom.co.jp/world/support/index.htm will get you to the right
> place.
> 
> Gary K8IZ
>  -------------- Original message ----------------------
> From: "Jay" <ad5pe at sbcglobal.net>
> > Guys,
> >  
> > I have a friend (an elderly ham) who's asked me to set up his newly 
> > acquired Tigertronics SL1+ to his Icom 706 (classic) so he can do digital
> modes.
> >  
> > He purchased it with the accessory "kit" for a 706 MkIIG.
> >  
> > The question concerns the accessory kit - it comes with a 13 pin (back 
> > of
> > 706) to modular 8 pin (back of SL1+) that "should" supply power (8v 
> > 10ma on pin 1) as well as handling PTT and audio both ways.  However, 
> > the SL1+ manual says to confirm this pin out from the owner's manual for
> the radio.
> > The problem is Bill doesn't have the manual for the 706, just the one 
> > for his other (mobile) radio - the MkIIG that's in his car.
> > 
> > Can anyone confirm that the pinouts are the same?  I can always go 
> > download the manual, but before I go on the "hunting expedition" I 
> > thought I'd ask the experts
> > 
> > Thanks,
> > Jay
> > AD5PE
> > 
> > ----
> > Your Moderator: Dick Flanagan K7VC, icom-owner at mailman.qth.net Icom 
> > Users Net: Sundays, 1700Z, 14.316 MHz Icom FAQ: 
> > http://www.qsl.net/icom/
> 
> 
> ----
> Your Moderator: Dick Flanagan K7VC, icom-owner at mailman.qth.net Icom Users
> Net: Sundays, 1700Z, 14.316 MHz Icom FAQ: http://www.qsl.net/icom/
> 
> ----
> Your Moderator: Dick Flanagan K7VC, icom-owner at mailman.qth.net
> Icom Users Net: Sundays, 1700Z, 14.316 MHz
> Icom FAQ: http://www.qsl.net/icom/




More information about the Icom mailing list