[ICOM] Icom PW1 Failures - How To

[Bruce J. Howes]

Hi Adam and group,

Not certain I agree that the antenna tuner in the PW1 functions when the
main switch is off at the PW1.
My ATU internal to the PW1, later serial #, does not work unless the power
is on to the PW-1.
I checked this with Icom, even if 12 volts is applied to the PW1 from the
765 exciter and the PW1 LEDs for the antenna and exciter input are
illuminated, the ATU will not work.
It will only work when the main power switch is on for the PW1.
The ATU will function with the amplifier section off, but not the main power
switch.

As far as determining antenna resonance, its really rather simple, MFJ-259.
The antenna is a 160 meter dipole fed with balanced line.
I am using a Heathkit 2060 tuner and the MFJ to confirm feedpoint impedance
and SWR.

The Icom manual for the PW1 does state on page 16, item 7 "Use the exciters
antenna tuner to tune the line between the IC-PW1/EURO and exciter, if you
have an antenna tuner connected to the exciter." 

I can't believe that the operation of a internal tuner of the exciter can or
should cause a fault in the SWR measuring circuit of the PW1, yet is has
happened to me and others.
Sorry, that seems like a design issue.
Can someone check the schematic and explain the failure of R7 on the
Splitter board any other way?

73 Bruce W1UJR

-----Original Message-----
From: icom-bounces at mailman.qth.net [mailto:icom-bounces at mailman.qth.net] On
Behalf Of Adam Farson
Sent: Wednesday, June 08, 2005 9:44 PM
To: 'ICOM Reflector'
Subject: RE: [ICOM] Icom PW-1 Failures - How To

Hi Harry,

Here is some further clarification courtesy Matt, KK5DR:

...The ATU can be operated without the PA section enabled. It can also be
operated without the PW1 even being powered up. DC power to operate the ATU
and antenna selector is provided by the exciter through the ACC cable. 

These features [Antenna selector & ATU operation with PW1 powered down] are
only provided on later versions of the PW1, S/N 1165 or higher.

The ATU requires at least 60 watts of drive to complete a tune cycle.  

Cheers for now, 73,
Adam VA7OJ/AB4OJ


-----Original Message-----
From: icom-bounces at mailman.qth.net [mailto:icom-bounces at mailman.qth.net] On
Behalf Of we1x at comcast.net
Sent: 08 June 2005 15:17
To: ICOM Reflector
Subject: RE: [ICOM] Icom PW-1 Failures - How To

Went back and tried it..I stand corrected.

thanks Adam.

Harry WE1X

-------------- Original message -------------- 

> Hi Harry,
> 
> To quote the PW1 user manual, p. 2: 
> 
> When the linear amplifier is OFF, the [AMP/PROTECT] does not light and 
> the exciter's signal is applied to one of the output connectors or the 
> IC-PW1's antenna tuner.
> 
> Ibid., p. 14, top: 
> 
> This antenna tuner is also used when the linear amplifier is turned 
> OFF.
> 
> The Yaesu Quadra can also be configured with ATU on-line and PA stage
> off-line: [OPERATE] key off, [TUNER] key on. 
> 
> The ATU insertion loss is approx. 0.5 dB. 
> 
> Cheers for now, 73,
> Adam VA7OJ/AB4OJ
> 
>


Scanned by WinProxy
http://www.Ositis.com/
----
Your Moderator: Dick Flanagan K7VC, icom-owner at mailman.qth.net Icom Users
Net: Sundays, 1700Z, 14.316 MHz Icom FAQ: http://www.qsl.net/icom/