[ICOM] PW 1

[William Diamond]

Thanks Harry,

How is the noise level on the PW1?  Right now, I installed the remote cable
but it tends to be too light to stay put on the desk.

The RF issue also concerns me also.  I have the one cable that came with it.
I am still in the early stages of hooking it up.



      William J. Diamond
       Rogers, Arkansas

    Ham Radio Operator WR0T

   Please Visit My Radio Site
        wjdiamond.com



-----Original Message-----
From: icom-bounces at mailman.qth.net
[mailto:icom-bounces at mailman.qth.net]On Behalf Of htankin at comcast.net
Sent: Saturday, June 26, 2004 10:36 PM
To: ICOM Reflector
Subject: RE: [ICOM] PW 1


Bill,

One accessory cable (7-pin DIN) should come with the PW-1.  I bought a
second from Burghardt's.  I believe the accessory cable is shielded, but not
certain.

I have heard reports that the cable for the remote head is not shielded, and
prone to picking up RF.

Harry WE1X


> Hi Johnny and the group.
>
> Did you make your own accy connect cable or did you get it from Icom???
>
> Does anyone know if the cable has to be shielded??
>
> Thanks
>
>       William J. Diamond
>        Rogers, Arkansas
>
>     Ham Radio Operator WR0T
>
>    Please Visit My Radio Site
>         wjdiamond.com
>
>
>
> -----Original Message-----
> From: icom-bounces at mailman.qth.net
> [mailto:icom-bounces at mailman.qth.net]On Behalf Of js
> Sent: Saturday, June 26, 2004 8:41 AM
> To: ICOM Reflector
> Subject: Re: [ICOM] PW 1
>
>
> Hi William,
>
> I am now running my pro2 and K2/100 with PW1.  I do not realise any
problem
> of RF nor any requirement of specific coax cable length.
>
> I do not see any problem in my case.  So far so good.
>
> 73
>
> Johnny Siu  VR2XMC
> ----- Original Message -----
> From: "William Diamond" <wjdiamond at sbcglobal.net>
> To: "Icom at Mailman. Qth. Net" <icom at mailman.qth.net>
> Sent: Saturday, June 26, 2004 12:12 PM
> Subject: [ICOM] PW 1
>
>
> > Hi all you PW 1 owners out there, I have a couple of questions.
> >
> > I am thinking of adding a 2nd Icom rig to the PW1 and is the coax cable
> > supposed to a specific length like the old Collins amps required?
> >
> > Is anyone running 2 rigs on one?  I am a bit concerned about that much
RF
> > being in the same box with a second rig?
> >
> > I remember what happened to my 2nd PRO II from a MFJ coax switch. I was
> > running one of them and it was selected by the coax switch and the front
> end
> > of the other one got wiped by the close spacing of the switch contacts
and
> I
> > was just running 100 W.
> >
> >       William J. Diamond
> >        Rogers, Arkansas
> >
> >     Ham Radio Operator WR0T
> >
> >    Please Visit My Radio Site
> >         wjdiamond.com
> >
> >
> >
> > ----
> > Your Moderator: Dick Flanagan K7VC, icom-owner at mailman.qth.net
> > Icom Users Net: Sundays, 1700Z, 14.316 MHz
> > Icom FAQ: http://www.qsl.net/icom/
> >
> ----
> Your Moderator: Dick Flanagan K7VC, icom-owner at mailman.qth.net
> Icom Users Net: Sundays, 1700Z, 14.316 MHz
> Icom FAQ: http://www.qsl.net/icom/
>
>
> ----
> Your Moderator: Dick Flanagan K7VC, icom-owner at mailman.qth.net
> Icom Users Net: Sundays, 1700Z, 14.316 MHz
> Icom FAQ: http://www.qsl.net/icom/
----
Your Moderator: Dick Flanagan K7VC, icom-owner at mailman.qth.net
Icom Users Net: Sundays, 1700Z, 14.316 MHz
Icom FAQ: http://www.qsl.net/icom/