[Icom] Icom 756-Pro II audio/mic input alternatives
anthony costa
[email protected]
Sun, 2 Jun 2002 19:35:29 -0400
It's all about the individual operator.running your pro out 3.0 will do
nothing to punch your audio through,furtermore if your signal is down due to
band conditions or whatever your not going to sound all that good.(muddy)now
if you ragchew with a net (14.178) and alway's deliver a 20 over signal then
i myself would run super wide and push up the high and low's to max.But it
just doesn't work that way in the real ham world.unless your stacking huge
monobander's up 120 feet with a gallon and a half behind that.that's not
feasable to 90% of all hams.so narrow the banwidth and adjust the bass and
treble to moderate level's.you will be heard better.
tony k2vi
----- Original Message -----
From: "HFSSB" <[email protected]>
To: <[email protected]>
Sent: Sunday, June 02, 2002 3:08 PM
Subject: RE: [Icom] Icom 756-Pro II audio/mic input alternatives
>
> It's unusual to find fault with Adam's outstanding contributions to our
hobby
> but re-reading Adam's comment here I see that the error is in the latter
part of
> this statement, "... to cut off low-frequency components of the microphone
> output (below 250~300 Hz). These components contribute virtually nothing
to
> articulation at the receiver,..."
>
> If we could take everything out of normal conversation below 250-300 Hz we
would
> quickly miss the richest sounding component of the human voice, the bass.
By
> putting this lower audio component back into the SSB signal we are adding
the
> fullness in the human voice giving it a more "life-like" natural sound.
Adam's
> statement is then only true if you receive with filters cutting off these
lower
> frequencies. Today however, there is tremendous interest in SSB audio
> improvement and you have Hams listening on rigs with filters opened up
from 0 Hz
> to 3-4k, even 6k if conditions allow.
>
> The problem comes when a novice in HiFi SSB (of course, we all start out
as
> novices) over-drives the low frequencies which then overpowers the mids
and
> highs, that's when you hear comments like "mushy audio". There is a
learning
> curve to the Ham audio hobby as in most things worth while. With the
exception
> of prejudice against the audio hobby itself, everyone who listens to a
properly
> balanced Hi-Fi audio SSB transmission on a properly adjusted and capable
> receiver (meaning filters open from 0-50 Hz to 3k or more and a decent
spkr or
> studio headphones) is at awe of the sounds that can come through in SSB
mode.
> It is not unusual to hear comments like "Sounds like FM broadcast
station".
>
> I have heard half a dozen or so 756 users who use the acc jack and without
> exception said they get better audio results by going direct to the
balanced
> modulator.
>
> Marty
> http://groups.yahoo.com/group/hfssbaudio/
>
> -----Original Message-----
> Adam I don't know what you know technically and I respect your knowledge
> however I am amble to run my Heil HC5 through the W2IHY EQ and noise gate
> and get a nicer and more full range of audio by going direct through the
> balance modulator than through the front mic input ...
> 73, Steve
> ----- Original Message -----
> > Larry,
> >...the design intent
> > is probably to cut off low-frequency components of the microphone output
> (below
> > 250~300 Hz). These components contribute virtually nothing to
articulation
> at
> > the receiver, ....
> > Best 73,
> > Adam, VA7OJ/AB4OJ
>
>
> ----
> Your Moderator: Dick Flanagan W6OLD, [email protected]
> Icom FAQ: http://www.qsl.net/icom/
>