[Heathkit] Source for 125 uf 450V electrolytics?

[crawfish]

Thanks!! Will take care of the DX-100 soon!!
                                                         Joe W4AAB
----- Original Message -----
From: "Robert & Linda McGraw (K4TAX)" <RMcGraw at Blomand.Net>
To: "crawfish" <crawfish at surfmore.net>; "Bob Young" <youngbob53 at msn.com>;
<Heathkit at mailman.qth.net>
Sent: Friday, February 02, 2007 8:18 PM
Subject: Re: [Heathkit] Source for 125 uf 450V electrolytics?


> I purchased mine from R F Parts.  Their part number is TVLU1775 which is
> rated as 100-150uF @ 500V.  Cost was $19.95 ea, required 2 pcs.  Also
> purchased a 031-464 which is a 40/20/10/10 @ 450V.  That one was $13.95.
> And added some new mounting plates, TMP-1 at $0.90 ea, required 3 pcs.
> Total to re-cap was $64.95 including s/h.
>
> 73
> Bob, K4TAX
>
>
> ----- Original Message -----
> From: "crawfish" <crawfish at surfmore.net>
> To: "Bob Young" <youngbob53 at msn.com>; <Heathkit at mailman.qth.net>
> Sent: Friday, February 02, 2007 6:36 PM
> Subject: Re: [Heathkit] Source for 125 uf 450V electrolytics?
>
>
> >I have some pins for the 1625-type sockets. While we are on the subject
of
> > DX-100 electrolytics, does anyone have any modern sources and part
number
> > for those caps? I need to replace all the electrolytics in my DX-100B.
> >                                                        Joe W4AAB
> >
> > Sent: Friday, February 02, 2007 6:01 PM
> > Subject: [Heathkit] Source for 125 uf 450V electrolytics?
> >
> >
> >> I was looking at the circuit of my DX-100 today which I haven't powered
> >> up
> >> yet and found a couple of problems, one, someone unhooked the two 125
uf
> >> cans and soldiered some Axial 100 uf 450 V electrolytics underneath in
> > their
> >> place.
> >> I was also lucky to notice that one of the sockets for one of the
1625's
> >> filiment clips had lost it's rivet and was just touching the bottom of
> >> the
> >> pin. I had taken this tube out before so I'm not sure if I did it or if
> >> it
> >> was already like that, the clip will and did snap on but I did find a
> > source
> >> for that: Antique Radio Supplies has one specifically for the 1625, was
> > one
> >> of the filiment pins.
> >>
> >> Bob Young
> >> Millbury, Ma KB1OKL
> >>
> >>
> >> _______________________________________________
> >> List Administrator: Duane Fischer, W8DBF
> >> ** For Assistance: dfischer at usol.com **
> >> $$ See the vintage area on the HCI web site - http://www.w9wze.org $$
> >> Heathkit mailing list
> >> Heathkit at mailman.qth.net
> >> http://mailman.qth.net/mailman/listinfo/heathkit
> >>
> >
> >
> > _______________________________________________
> > List Administrator: Duane Fischer, W8DBF
> > ** For Assistance: dfischer at usol.com **
> > $$ See the vintage area on the HCI web site - http://www.w9wze.org $$
> > Heathkit mailing list
> > Heathkit at mailman.qth.net
> > http://mailman.qth.net/mailman/listinfo/heathkit
> >
>
>
> _______________________________________________
> List Administrator: Duane Fischer, W8DBF
> ** For Assistance: dfischer at usol.com **
> $$ See the vintage area on the HCI web site - http://www.w9wze.org $$
> Heathkit mailing list
> Heathkit at mailman.qth.net
> http://mailman.qth.net/mailman/listinfo/heathkit
>