From bcarling at cfl.rr.com  Sun Aug  3 21:21:11 2014
From: bcarling at cfl.rr.com (bcarling at cfl.rr.com)
Date: Sun, 03 Aug 2014 21:21:11 -0400
Subject: [HBR] REDUCED MORE: 160m CRYSTALS!!
Message-ID: <53DEE007.2436.170C568@bcarling.cfl.rr.com>

Hey folks - I have added a bunch more "Bargain Basement 160m crystals for sale plus I have 
dropped the price on most of these a further 20% - some of the earlier ones were sold but 
not all!

So here is your opportunity. These are original clean hc6u crystals all fully tested and in 
proper working condition. Check out the expanded list below, and you can purchase directly 
online or mail order if you prefer. 

REDUCED MORE: 160m hc6u (metal can) crystals -

This select group on sale for only $5.00 each.

Quantities shown as of 1 AUGUST 2014

FREQUENCY kHz - QUANTITY

1800        -   1
1801        -   1
1835        -   1
1849        -   1
1908.125- 2
1916 - 1
1928        -   1
1929        -   1
1932 - 5
1933        -   1
1935        -   1
1936        -   1
1940        -   1
1942 - 4
1944 - 3
1945 - 6

Shipping additional. (numerous other 160m - 2m frequencies available.)

Purchase on line at:

http://af4k.com/hc6ucrystals1500-1999khz.htm

73 - Bry Carling, AF4K
Brian Carling, Radio AF4K

From bcarling at cfl.rr.com  Fri Aug 15 09:41:08 2014
From: bcarling at cfl.rr.com (bcarling at cfl.rr.com)
Date: Fri, 15 Aug 2014 09:41:08 -0400
Subject: [HBR] FS: ORIGINAL FT243 Ham Crystals
Message-ID: <53EE0DF4.127.5C7EEBF@bcarling.cfl.rr.com>

Selling:

ORIGINAL FT243 Amateur Band Crystals - $16.00 each.
(for those who prefer full sized quartz.) In most cases I have only one of these. 

Examples:
1955,  3560,  3640,  3654,  3720,  3735,  3800,  3858, 3897 3995 kHz

7000,  7001.2,   7004.2,   7008.7,   7019.7,   7022,   7024.2,   7025 kHz
7033.8,   7043.7,   7048.3,   7050,   7053.4,   7075,   7100,   7125 kHz
7128,   7140,   7150,   7170,   7185,   7225,   7250,   7270,   7275 kHz
8375,   8400,   8425,  14213 kHz

Many others available for ordering directly at:
http://af4k.com/FT243_CRYSTALS_Originals.htm

When they are gone, they are gone.  Suggestion is to buy more than one and save on 
shipping. 

73 & thanks for looking - Bry Carling, AF4K


Brian Carling, Radio AF4K

From brian at lessonsinlutherie.com  Sat Aug 16 12:04:03 2014
From: brian at lessonsinlutherie.com (Brian Burns)
Date: Sat, 16 Aug 2014 09:04:03 -0700
Subject: [HBR] Pullen vs diode ring mixers
Message-ID: <!&!AAAAAAAAAAAYAAAAAAAAAO9WiXwKTRJMveKqmcXf97/CgAAAEAAAALYuBdBb6uVCmimQW1WJILYBAAAAAA==@lessonsinlutherie.com>

Hello All,

 

A fellow over on the funwithtubes list mentioned the 6JU8 quad diode as a
candidate for a diode ring mixer, and being a confirmed glowbugger, the idea
"tickled my whiskers". Is there any received wisdom in the group on the
relative merits of the Pullen versus the diode ring mixer?

 

An ancillary question: I ran across a mention of the "double balanced"
mixer, but not much info. That's another interesting idea, as it seems to
afford some useful cancellation of unwanted output frequencies.

 

Any comments or links to more information greatly appreciated (:->).

 

Cheers,

 

Brian Burns   Ex: W5BRO, K6UCD 

 

 



---
This email is free from viruses and malware because avast! Antivirus protection is active.
http://www.avast.com

From tshoppa at wmata.com  Sat Aug 16 15:03:47 2014
From: tshoppa at wmata.com (Shoppa, Tim)
Date: Sat, 16 Aug 2014 19:03:47 +0000
Subject: [HBR] Pullen vs diode ring mixers
In-Reply-To: <!&!AAAAAAAAAAAYAAAAAAAAAO9WiXwKTRJMveKqmcXf97/CgAAAEAAAALYuBdBb6uVCmimQW1WJILYBAAAAAA==@lessonsinlutherie.com>
References: <!&!AAAAAAAAAAAYAAAAAAAAAO9WiXwKTRJMveKqmcXf97/CgAAAEAAAALYuBdBb6uVCmimQW1WJILYBAAAAAA==@lessonsinlutherie.com>
Message-ID: <303A17BD5F8FA34DA45EEC245271AC0BB7343ED5@JGEX2K10MBX2.wmata.local>

The diode ring mixer is an example of a "Doubly balanced" mixer.

I think in old ARRL Handbooks and especially "SSB handbooks" you can find examples of quad diode tubes being put to use as DBM's. The transformer winding details should prove useful.

Tim N3QE
_____________________________________
From: HBR [hbr-bounces at mailman.qth.net] on behalf of Brian Burns [brian at lessonsinlutherie.com]
Sent: Saturday, August 16, 2014 12:04 PM
To: hbr at mailman.qth.net
Subject: [HBR] Pullen vs diode ring mixers

Hello All,



A fellow over on the funwithtubes list mentioned the 6JU8 quad diode as a
candidate for a diode ring mixer, and being a confirmed glowbugger, the idea
"tickled my whiskers". Is there any received wisdom in the group on the
relative merits of the Pullen versus the diode ring mixer?



An ancillary question: I ran across a mention of the "double balanced"
mixer, but not much info. That's another interesting idea, as it seems to
afford some useful cancellation of unwanted output frequencies.



Any comments or links to more information greatly appreciated (:->).



Cheers,



Brian Burns   Ex: W5BRO, K6UCD







---
This email is free from viruses and malware because avast! Antivirus protection is active.
http://www.avast.com
______________________________________________________________
HBR mailing list
Home: http://mailman.qth.net/mailman/listinfo/hbr
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:HBR at mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

From brianburns1066 at gmail.com  Sat Aug 16 16:04:49 2014
From: brianburns1066 at gmail.com (Brian Burns)
Date: Sat, 16 Aug 2014 13:04:49 -0700
Subject: [HBR] Pullen vs diode ring mixers
In-Reply-To: <303A17BD5F8FA34DA45EEC245271AC0BB7343ED5@JGEX2K10MBX2.wmata.local>
References: <!&!AAAAAAAAAAAYAAAAAAAAAO9WiXwKTRJMveKqmcXf97/CgAAAEAAAALYuBdBb6uVCmimQW1WJILYBAAAAAA==@lessonsinlutherie.com>
	<303A17BD5F8FA34DA45EEC245271AC0BB7343ED5@JGEX2K10MBX2.wmata.local>
Message-ID: <!&!AAAAAAAAAAAYAAAAAAAAAO9WiXwKTRJMveKqmcXf97/CgAAAEAAAAGRQhY+6D7tJi840EFuCw6MBAAAAAA==@gmail.com>

Hello Tim,

~ The diode ring mixer is an example of a "Doubly balanced" mixer.

~ I think in old ARRL Handbooks and especially "SSB handbooks" you can find
examples of quad diode tubes being put to use as DBM's. The transformer
winding details should prove useful.

~ Tim N3QE

Thanks very much! That's just the sort of information I was looking
for---I'm off to my shelf of reference books (:->)...

Cheers,

Brian


---
This email is free from viruses and malware because avast! Antivirus protection is active.
http://www.avast.com


From hbr at mailman.qth.net  Sat Aug 16 16:18:15 2014
From: hbr at mailman.qth.net (Bill Murray via HBR)
Date: Sat, 16 Aug 2014 16:18:15 -0400
Subject: [HBR] HBR Digest, Vol 118, Issue 1
In-Reply-To: <mailman.5171.1408219509.11568.hbr@mailman.qth.net>
References: <mailman.5171.1408219509.11568.hbr@mailman.qth.net>
Message-ID: <5DDE7749-9E25-48EE-BECF-9E45AF728B01@aol.com>

I would prefer that people who are parts dealers not clutter this site with long ads for parts that are readily available and arnt really related to HBR construction. I don't think that is the intent of the site. I occasionally  sell parts and tubes on both qth and ebay, but I don't force the group to sift thru my for sale info before getting to the intended content. Thats what those other sites are intended for. I think it's a different story if a individual ham is liquidating his HBR parts inventory, or has a hard to find part such as the special variable cap needed, if transformers , or the Eddystone dial. just my opinion. 73's to all Bill W9VC

Sent from my iPad

On Aug 16, 2014, at 4:05 PM, hbr-request at mailman.qth.net wrote:

> Send HBR mailing list submissions to
>    hbr at mailman.qth.net
> 
> To subscribe or unsubscribe via the World Wide Web, visit
>    http://mailman.qth.net/mailman/listinfo/hbr
> or, via email, send a message with subject or body 'help' to
>    hbr-request at mailman.qth.net
> 
> You can reach the person managing the list at
>    hbr-owner at mailman.qth.net
> 
> When replying, please edit your Subject line so it is more specific
> than "Re: Contents of HBR digest..."
> 
> 
> Today's Topics:
> 
>   1. PARTS etc. FOR SALE (bcarling at cfl.rr.com)
>   2. REDUCED MORE: 160m CRYSTALS!! (bcarling at cfl.rr.com)
>   3. FS: ORIGINAL FT243 Ham Crystals (bcarling at cfl.rr.com)
>   4. Pullen vs diode ring mixers (Brian Burns)
>   5. Re: Pullen vs diode ring mixers (Shoppa, Tim)
>   6. Re: Pullen vs diode ring mixers (Brian Burns)
> 
> 
> ----------------------------------------------------------------------
> 
> Message: 1
> Date: Wed, 23 Jul 2014 14:10:47 -0400
> From: bcarling at cfl.rr.com
> To: HAMtrade at yahoogroups.com, hbr at mailman.qth.net,
>    heathkit at yahoogroups.com,    heath at puck.nether.net,
>    heathkit at mailman.qth.net
> Subject: [HBR] PARTS etc. FOR SALE
> Message-ID: <53CFFAA7.3924.53E0ED at bcarling.cfl.rr.com>
> Content-Type: text/plain; charset=US-ASCII
> 
> PARTS etc. FOR SALE
> 
> 1) Barker and Williamson Coaxial Antenna Switch model 592 (two way) - excellent condition 
> QTY 1 available for $32.00 plus shipping
> 
> 2) Sprague 8 uF at 1000V DC oil-filled capacitor. Tested and works fine, no leakage or
> other issues. Dimensions 3.75"  X  1.25"  X  5.25" tall
> QTY 1 available for $6.00 plus shipping
> 
> 3) Pair of ceramic octal sockets wired for 6146 tubes, an a small copper plated subchassis, 
> with a nice 2.5 mH choke, ceramic feedthru etc. $5.00 plus shipping
> 
> 4) - Box of 16 power resistors and bleeder resistors, Ohmite etc. mostly 25, 50 and 100 watt.
> Examples:  100 ohms at 100 watts,  12K at 100 watts, 14K at 50 watts, 15K at 72 watts,  16K 
> at 50 watts,  20K at 100 watts, 24K at 72 watts,  25K at 100 watts, etc. This is about 10% of 
> list price:
> Available - all 15 for $25.00 plus shipping
> 
> 5) DX100 plate tank coil including extra 160m coil - $5.00
> 
> 6) RFC - Plate choke from a Viking II transmitter - $5.00
> 
> 7) Pair of 10K at 10 watts resistors, plus one 15K at 10 watts from DX100 - $4.00 for all 3.
> 
> 8) Panel Meter from DX100 Transmitter - $10.00
> 
> 9) Chassis for DX100 Transmitter - $20.00
> 
> 10)  VFO assembly for DX100 - $20.00
> 
> 11) Transformer with secondary: 50V AC at 20 Amps. Like new, scientific grade, and in 
> excellent condition.
> Primary is 120V AC and this is a beautiful workhorse transformer. 4 hole mounting. 
> Dimensions:  7" X 6.5" X 4.5" tall.
> QTY 1 available for $25.00 plus $15 for USA shipping
> 
> 12) Pair of ceramic 807 sockets with mounting hardware - $5.00
> 
> 13)  Pair of ceramic plate caps for 807 tubes Millen - $4.00
> 
> 14) Microphone socket for DX100 - 2-pin with hardware - $4.00
> 
> 15) Group of capacitors - One Astron 0.1 uF at 600V DC, Two 0.05 at 1600V DC, One 
> 0.0002 uF at 1200V and two electrolytics 40 uF at 450V DC. These are good tested used 
> parts. The 0.1 and 0.05 ones have usable short leads - others normal. Also,  one DX100 
> Fixed loading capacitor HV, switches in parallel to the loading variable capacitor. 
> Total of 7 capacitors for $6.00
> 
> 16) New Silver mica 0.001 uF capacitors at 2500V DC. Available for $6.00 each while they 
> last.
> 
> 17) G.E. MASTR external speaker $5.00
> 
> 18) G.E. mobile Power supply for two way radio - $5.00
> 
> 19) Three black IERC tube shields, heat dissipating types, for 7 pin miniature tubes.
> $6.00 for all three.
> 
> 20) HAL-TRONIX model HAL FC-600A frequency counter. Good working condition. BNC 
> inputs and runs on 120V AC. I have no manual for this. Available for $15.00 plus shipping.
> 
> 21)  6Y6G tube made by G.E. - QTY 1 available for $3.00
> 
> 22) 811 Transmitting tube Penta Labs - looks new - $12.00
> 
> 23) 5R4WGY tube new in box JAN type from Chatham Electronics - $5.00
> 
> 24) 5T4 tube, new - $2.00
> 
> 25) 6146 (S2001A) from Matsushita - looks new, like 6146 - $6.00
> 
> 26) Mullard TDD2A gold tube new in box - $10.00
> 
> 27) 3B28 rectifier tube - JAN - QTY 1 only for $4.00
> 
> Shipping additional on all the above.  For additional details, pictures or questions, 
> please e-mail me off the list.
> 
> 73 & thanks for looking
> 
> Brian Carling, AF4K
> Brian Carling, Radio AF4K
> 
> 
> ------------------------------
> 
> Message: 2
> Date: Sun, 03 Aug 2014 21:21:11 -0400
> From: bcarling at cfl.rr.com
> To: HamRadioPartsOnly at yahoogroups.com,
>    hamradiotradersclub at yahoogroups.com,    HAMtrade at yahoogroups.com,
>    hbr at mailman.qth.net, heathkit at yahoogroups.com
> Subject: [HBR] REDUCED MORE: 160m CRYSTALS!!
> Message-ID: <53DEE007.2436.170C568 at bcarling.cfl.rr.com>
> Content-Type: text/plain; charset=US-ASCII
> 
> Hey folks - I have added a bunch more "Bargain Basement 160m crystals for sale plus I have 
> dropped the price on most of these a further 20% - some of the earlier ones were sold but 
> not all!
> 
> So here is your opportunity. These are original clean hc6u crystals all fully tested and in 
> proper working condition. Check out the expanded list below, and you can purchase directly 
> online or mail order if you prefer. 
> 
> REDUCED MORE: 160m hc6u (metal can) crystals -
> 
> This select group on sale for only $5.00 each.
> 
> Quantities shown as of 1 AUGUST 2014
> 
> FREQUENCY kHz - QUANTITY
> 
> 1800        -   1
> 1801        -   1
> 1835        -   1
> 1849        -   1
> 1908.125- 2
> 1916 - 1
> 1928        -   1
> 1929        -   1
> 1932 - 5
> 1933        -   1
> 1935        -   1
> 1936        -   1
> 1940        -   1
> 1942 - 4
> 1944 - 3
> 1945 - 6
> 
> Shipping additional. (numerous other 160m - 2m frequencies available.)
> 
> Purchase on line at:
> 
> http://af4k.com/hc6ucrystals1500-1999khz.htm
> 
> 73 - Bry Carling, AF4K
> Brian Carling, Radio AF4K
> 
> 
> ------------------------------
> 
> Message: 3
> Date: Fri, 15 Aug 2014 09:41:08 -0400
> From: bcarling at cfl.rr.com
> To: hamradiotradersclub at yahoogroups.com, HAMtrade at yahoogroups.com,
>    hbr at mailman.qth.net, heathkit at yahoogroups.com
> Subject: [HBR] FS: ORIGINAL FT243 Ham Crystals
> Message-ID: <53EE0DF4.127.5C7EEBF at bcarling.cfl.rr.com>
> Content-Type: text/plain; charset=US-ASCII
> 
> Selling:
> 
> ORIGINAL FT243 Amateur Band Crystals - $16.00 each.
> (for those who prefer full sized quartz.) In most cases I have only one of these. 
> 
> Examples:
> 1955,  3560,  3640,  3654,  3720,  3735,  3800,  3858, 3897 3995 kHz
> 
> 7000,  7001.2,   7004.2,   7008.7,   7019.7,   7022,   7024.2,   7025 kHz
> 7033.8,   7043.7,   7048.3,   7050,   7053.4,   7075,   7100,   7125 kHz
> 7128,   7140,   7150,   7170,   7185,   7225,   7250,   7270,   7275 kHz
> 8375,   8400,   8425,  14213 kHz
> 
> Many others available for ordering directly at:
> http://af4k.com/FT243_CRYSTALS_Originals.htm
> 
> When they are gone, they are gone.  Suggestion is to buy more than one and save on 
> shipping. 
> 
> 73 & thanks for looking - Bry Carling, AF4K
> 
> 
> Brian Carling, Radio AF4K
> 
> 
> ------------------------------
> 
> Message: 4
> Date: Sat, 16 Aug 2014 09:04:03 -0700
> From: "Brian Burns" <brian at lessonsinlutherie.com>
> To: <hbr at mailman.qth.net>
> Subject: [HBR] Pullen vs diode ring mixers
> Message-ID:
>    <!&!AAAAAAAAAAAYAAAAAAAAAO9WiXwKTRJMveKqmcXf97/CgAAAEAAAALYuBdBb6uVCmimQW1WJILYBAAAAAA==@lessonsinlutherie.com>
>    
> Content-Type: text/plain;    charset="US-ASCII"
> 
> Hello All,
> 
> 
> 
> A fellow over on the funwithtubes list mentioned the 6JU8 quad diode as a
> candidate for a diode ring mixer, and being a confirmed glowbugger, the idea
> "tickled my whiskers". Is there any received wisdom in the group on the
> relative merits of the Pullen versus the diode ring mixer?
> 
> 
> 
> An ancillary question: I ran across a mention of the "double balanced"
> mixer, but not much info. That's another interesting idea, as it seems to
> afford some useful cancellation of unwanted output frequencies.
> 
> 
> 
> Any comments or links to more information greatly appreciated (:->).
> 
> 
> 
> Cheers,
> 
> 
> 
> Brian Burns   Ex: W5BRO, K6UCD 
> 
> 
> 
> 
> 
> 
> 
> ---
> This email is free from viruses and malware because avast! Antivirus protection is active.
> http://www.avast.com
> 
> 
> ------------------------------
> 
> Message: 5
> Date: Sat, 16 Aug 2014 19:03:47 +0000
> From: "Shoppa, Tim" <tshoppa at wmata.com>
> To: HBR Receiver List <hbr at mailman.qth.net>
> Subject: Re: [HBR] Pullen vs diode ring mixers
> Message-ID:
>    <303A17BD5F8FA34DA45EEC245271AC0BB7343ED5 at JGEX2K10MBX2.wmata.local>
> Content-Type: text/plain; charset="us-ascii"
> 
> The diode ring mixer is an example of a "Doubly balanced" mixer.
> 
> I think in old ARRL Handbooks and especially "SSB handbooks" you can find examples of quad diode tubes being put to use as DBM's. The transformer winding details should prove useful.
> 
> Tim N3QE
> _____________________________________
> From: HBR [hbr-bounces at mailman.qth.net] on behalf of Brian Burns [brian at lessonsinlutherie.com]
> Sent: Saturday, August 16, 2014 12:04 PM
> To: hbr at mailman.qth.net
> Subject: [HBR] Pullen vs diode ring mixers
> 
> Hello All,
> 
> 
> 
> A fellow over on the funwithtubes list mentioned the 6JU8 quad diode as a
> candidate for a diode ring mixer, and being a confirmed glowbugger, the idea
> "tickled my whiskers". Is there any received wisdom in the group on the
> relative merits of the Pullen versus the diode ring mixer?
> 
> 
> 
> An ancillary question: I ran across a mention of the "double balanced"
> mixer, but not much info. That's another interesting idea, as it seems to
> afford some useful cancellation of unwanted output frequencies.
> 
> 
> 
> Any comments or links to more information greatly appreciated (:->).
> 
> 
> 
> Cheers,
> 
> 
> 
> Brian Burns   Ex: W5BRO, K6UCD
> 
> 
> 
> 
> 
> 
> 
> ---
> This email is free from viruses and malware because avast! Antivirus protection is active.
> http://www.avast.com
> ______________________________________________________________
> HBR mailing list
> Home: http://mailman.qth.net/mailman/listinfo/hbr
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:HBR at mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> 
> 
> ------------------------------
> 
> Message: 6
> Date: Sat, 16 Aug 2014 13:04:49 -0700
> From: Brian Burns <brianburns1066 at gmail.com>
> To: "'HBR Receiver List'" <hbr at mailman.qth.net>
> Subject: Re: [HBR] Pullen vs diode ring mixers
> Message-ID:
>    <!&!AAAAAAAAAAAYAAAAAAAAAO9WiXwKTRJMveKqmcXf97/CgAAAEAAAAGRQhY+6D7tJi840EFuCw6MBAAAAAA==@gmail.com>
>    
> Content-Type: text/plain;    charset="us-ascii"
> 
> Hello Tim,
> 
> ~ The diode ring mixer is an example of a "Doubly balanced" mixer.
> 
> ~ I think in old ARRL Handbooks and especially "SSB handbooks" you can find
> examples of quad diode tubes being put to use as DBM's. The transformer
> winding details should prove useful.
> 
> ~ Tim N3QE
> 
> Thanks very much! That's just the sort of information I was looking
> for---I'm off to my shelf of reference books (:->)...
> 
> Cheers,
> 
> Brian
> 
> 
> ---
> This email is free from viruses and malware because avast! Antivirus protection is active.
> http://www.avast.com
> 
> 
> 
> ------------------------------
> 
> Subject: Digest Footer
> 
> _______________________________________________
> HBR mailing list
> HBR at mailman.qth.net
> http://mailman.qth.net/mailman/listinfo/hbr
> 
> 
> ------------------------------
> 
> End of HBR Digest, Vol 118, Issue 1
> ***********************************

From hbr at mailman.qth.net  Sat Aug 16 18:29:16 2014
From: hbr at mailman.qth.net (Ron Barlow via HBR)
Date: Sat, 16 Aug 2014 15:29:16 -0700
Subject: [HBR] Pullen vs diode ring mixers
In-Reply-To: <303A17BD5F8FA34DA45EEC245271AC0BB7343ED5@JGEX2K10MBX2.wmata.local>
Message-ID: <1408228156.10513.YahooMailBasic@web160105.mail.bf1.yahoo.com>

One of the things that I like about the Pullen, based on my limited experience (2 different HF down converters), is that very little LO power was required for optimum conversion gain. Thus, good local oscillator stability was easier to achieve.
 I suspect that a passive DBM would require substantially more LO power, based on what I have read about usage of same at VHF and above. However, I can not offer proof of this.
 The Pullen probably would have less tolorance to overload, but it was adequately crunch proof, at my QTH. I could not say the same for another dual triode mixer, that I previously used in a 30m downconverter.
               73 de Ron  n4gjv
--------------------------------------------
On Sat, 8/16/14, Shoppa, Tim <tshoppa at wmata.com> wrote:

 Subject: Re: [HBR] Pullen vs diode ring mixers
 To: "HBR Receiver List" <hbr at mailman.qth.net>
 Date: Saturday, August 16, 2014, 3:03 PM
 
 The diode ring mixer is
 an example of a "Doubly balanced" mixer.
 
 I think in old ARRL Handbooks
 and especially "SSB handbooks" you can find
 examples of quad diode tubes being put to use as DBM's.
 The transformer winding details should prove useful.
 
 Tim N3QE
 _____________________________________
 From: HBR [hbr-bounces at mailman.qth.net]
 on behalf of Brian Burns [brian at lessonsinlutherie.com]
 Sent: Saturday, August 16, 2014 12:04 PM
 To: hbr at mailman.qth.net
 Subject: [HBR] Pullen vs diode ring mixers
 
 Hello All,
 
 
 
 A fellow over
 on the funwithtubes list mentioned the 6JU8 quad diode as
 a
 candidate for a diode ring mixer, and
 being a confirmed glowbugger, the idea
 "tickled my whiskers". Is there any
 received wisdom in the group on the
 relative
 merits of the Pullen versus the diode ring mixer?
 
 
 
 An ancillary question: I ran across a mention
 of the "double balanced"
 mixer,
 but not much info. That's another interesting idea, as
 it seems to
 afford some useful cancellation
 of unwanted output frequencies.
 
 
 
 Any comments
 or links to more information greatly appreciated
 (:->).
 
 
 
 Cheers,
 
 
 
 Brian
 Burns???Ex: W5BRO, K6UCD
 
 
 
 
 
 
 
 ---
 This email is free from
 viruses and malware because avast! Antivirus protection is
 active.
 http://www.avast.com
 ______________________________________________________________
 HBR mailing list
 Home: http://mailman.qth.net/mailman/listinfo/hbr
 Help: http://mailman.qth.net/mmfaq.htm
 Post: mailto:HBR at mailman.qth.net
 
 This list hosted by: http://www.qsl.net
 Please help support this email list: http://www.qsl.net/donate.html
 ______________________________________________________________
 HBR mailing list
 Home: http://mailman.qth.net/mailman/listinfo/hbr
 Help: http://mailman.qth.net/mmfaq.htm
 Post: mailto:HBR at mailman.qth.net
 
 This list hosted by: http://www.qsl.net
 Please help support this email list: http://www.qsl.net/donate.html
 

From rrfowler0429 at att.net  Sat Aug 16 22:13:26 2014
From: rrfowler0429 at att.net (Ralph Fowler)
Date: Sat, 16 Aug 2014 21:13:26 -0500
Subject: [HBR] Homebrew parts for sale
Message-ID: <804AD315-C106-491D-889C-131FE568883C@att.net>

0-99 turns counter - $35
Very heavy duty and excellent condition 16.5 uH rotary inductor - $100
3 silver plated coils - $10
2 high power multi pole relays, 24 vdc coils - $10
2 ea filter caps: 32 uF at 4500 vdc; 20 uF at 1500 vdc - $50
Magnecraft 5kvdc HV relay, 24vdc coil - $10
Cramer hour meter - $10
0-30 sec Eagle timer - $10
DP Airpax circuit breaker, 15a @ 250v, 60 Hz - $5
2ea Sprague 250vac line filters, 15a. - $20

Sent from Ralph's Ipad

From hbr at mailman.qth.net  Sun Aug 17 07:52:03 2014
From: hbr at mailman.qth.net (Hopperdhh--- via HBR)
Date: Sun, 17 Aug 2014 07:52:03 -0400 (EDT)
Subject: [HBR] Homebrew parts for sale
Message-ID: <7bd36.1b32021d.4121f163@aol.com>



Just what I need for my HBR project.
 
 
 
 
In a message dated 8/17/2014 5:02:07 A.M. Eastern Daylight Time,  
rrfowler0429 at att.net writes:

0-99  turns counter - $35
Very heavy duty and excellent condition 16.5 uH rotary  inductor - $100
3 silver plated coils - $10
2 high power multi pole  relays, 24 vdc coils - $10
2 ea filter caps: 32 uF at 4500 vdc; 20 uF at 1500 vdc  - $50
Magnecraft 5kvdc HV relay, 24vdc coil - $10
Cramer hour meter -  $10
0-30 sec Eagle timer - $10
DP Airpax circuit breaker, 15a @ 250v, 60  Hz - $5
2ea Sprague 250vac line filters, 15a. - $20

Sent from  Ralph's  Ipad
______________________________________________________________
HBR  mailing list
Home: http://mailman.qth.net/mailman/listinfo/hbr
Help:  http://mailman.qth.net/mmfaq.htm
Post:  mailto:HBR at mailman.qth.net

This list hosted by:  http://www.qsl.net
Please help support this email list:  http://www.qsl.net/donate.html


From rrfowler0429 at att.net  Sun Aug 17 19:05:41 2014
From: rrfowler0429 at att.net (Ralph Fowler)
Date: Sun, 17 Aug 2014 18:05:41 -0500
Subject: [HBR] Balanced inductor antenna tuner
Message-ID: <6A086603-C23F-4623-9C9E-2E599A9B6DA2@att.net>

Balanced inductor antenna tuner

Stepper motor controlled balanced inductor antenna tuner - incomplete but good project start. Good for parts and worked last time I worked on it few years ago. Built on a 1/8" panel.

Can't remember the connections to the stepper motors but there should be lots of info on Internet. And you will need to buy a stepper motor controller - kits available from several suppliers. There are also two 10 turn pots in the homebrew gear box to monitor position of the inductor and tuning cap.

$100 plus shipping. Email for picture.


From radioconnection at gmail.com  Sun Aug 17 20:15:21 2014
From: radioconnection at gmail.com (Peter Bertini)
Date: Sun, 17 Aug 2014 20:15:21 -0400
Subject: [HBR] Balanced inductor antenna tuner
In-Reply-To: <6A086603-C23F-4623-9C9E-2E599A9B6DA2@att.net>
References: <6A086603-C23F-4623-9C9E-2E599A9B6DA2@att.net>
Message-ID: <CA+uDY2Rw+eGkCK19fe-RZCQ0Q-0JNphBzSbC1Uqf_oGL=iSudw@mail.gmail.com>

What is the purpose of all of this off topic sales nonsense?


On Sun, Aug 17, 2014 at 7:05 PM, Ralph Fowler <rrfowler0429 at att.net> wrote:

> Balanced inductor antenna tuner
>
> Stepper motor controlled balanced inductor antenna tuner - incomplete but
> good project start. Good for parts and worked last time I worked on it few
> years ago. Built on a 1/8" panel.
>
> Can't remember the connections to the stepper motors but there should be
> lots of info on Internet. And you will need to buy a stepper motor
> controller - kits available from several suppliers. There are also two 10
> turn pots in the homebrew gear box to monitor position of the inductor and
> tuning cap.
>
> $100 plus shipping. Email for picture.
>
> ______________________________________________________________
> HBR mailing list
> Home: http://mailman.qth.net/mailman/listinfo/hbr
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:HBR at mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
>

From mcinsand at gmail.com  Mon Aug 18 09:01:37 2014
From: mcinsand at gmail.com (Stan McIntosh)
Date: Mon, 18 Aug 2014 09:01:37 -0400
Subject: [HBR] off-topic reminds me of on-topic questions
Message-ID: <CAKVLtWPxr_7cUrvXb0uJ+u3wtpJGVZGdJuZ9cyiDOC9gqqabaQ@mail.gmail.com>

The balanced inductor antenna tuner reminds me of some on-topic thoughts
that I have been thinking.  Reduction drives are still available, but they
can be pricey and hard to find.  However, I have lately been playing with
stepper motors, and I am thinking of trying to adapt (at least) one to VFO
use.  If you'll search the term 28BYJ-48, you'll find a motor where you can
get 5 motors with driver boards for $15 after shipping, and these pair
nicely with a $5 Arduino board and a $2 bluetooth adapter.  These motors
may only move in steps, but we're talking about over 4000 steps/revolution
(the internal motor is 64 steps/revolution with a 63.something:1 reduction
drive in the case).  The reason I mentioned bluetooth is that I'm often
lazy with the Arduinos; rather than put controls on the case, I'll just
send setting information back and forth from my phone.

Sorry if this is blasphemous by munging solid-state with HBR, but I have
been thinking about this as a way to make fine tuning easier.

Regards,
Stan
kd4bth

From wrcromwell at gmail.com  Mon Aug 18 09:34:38 2014
From: wrcromwell at gmail.com (Bill Cromwell)
Date: Mon, 18 Aug 2014 09:34:38 -0400
Subject: [HBR] off-topic reminds me of on-topic questions
In-Reply-To: <CAKVLtWPxr_7cUrvXb0uJ+u3wtpJGVZGdJuZ9cyiDOC9gqqabaQ@mail.gmail.com>
References: <CAKVLtWPxr_7cUrvXb0uJ+u3wtpJGVZGdJuZ9cyiDOC9gqqabaQ@mail.gmail.com>
Message-ID: <53F200EE.1020406@gmail.com>

Hi Stan,

I'm a knob twister myself. Some other hams have done just about exactly 
what you have in mind with steppers and gears for remote tuners and for 
other controls such as your VFO. Watch out for the digital hash noise in 
your receiver while you are using that stepper system. The noise can be 
controlled but I have only bague notions about what they did to suppress 
the noise. After all, I'm a knob twister and the motors I use for that 
do not interfere with the receiver <evil grin>.

Google may help you find the info that is available on the web. Good 
luck with your project.

73,

Bill  KU8H

On 08/18/2014 09:01 AM, Stan McIntosh wrote:
> The balanced inductor antenna tuner reminds me of some on-topic thoughts
> that I have been thinking.  Reduction drives are still available, but they
> can be pricey and hard to find.  However, I have lately been playing with
> stepper motors, and I am thinking of trying to adapt (at least) one to VFO
> use.  If you'll search the term 28BYJ-48, you'll find a motor where you can
> get 5 motors with driver boards for $15 after shipping, and these pair
> nicely with a $5 Arduino board and a $2 bluetooth adapter.  These motors
> may only move in steps, but we're talking about over 4000 steps/revolution
> (the internal motor is 64 steps/revolution with a 63.something:1 reduction
> drive in the case).  The reason I mentioned bluetooth is that I'm often
> lazy with the Arduinos; rather than put controls on the case, I'll just
> send setting information back and forth from my phone.
>
> Sorry if this is blasphemous by munging solid-state with HBR, but I have
> been thinking about this as a way to make fine tuning easier.
>
> Regards,
> Stan
> kd4bth
>


From tshoppa at wmata.com  Mon Aug 18 09:52:59 2014
From: tshoppa at wmata.com (Shoppa, Tim)
Date: Mon, 18 Aug 2014 13:52:59 +0000
Subject: [HBR] off-topic reminds me of on-topic questions
In-Reply-To: <CAKVLtWPxr_7cUrvXb0uJ+u3wtpJGVZGdJuZ9cyiDOC9gqqabaQ@mail.gmail.com>
References: <CAKVLtWPxr_7cUrvXb0uJ+u3wtpJGVZGdJuZ9cyiDOC9gqqabaQ@mail.gmail.com>
Message-ID: <303A17BD5F8FA34DA45EEC245271AC0BB7344ABA@JGEX2K10MBX2.wmata.local>

You would be surprised, how much it helps with fine tuning to replace a dinky little knob with a reasonable or big-sized knob.

Yes, it's still the same Hz per degree of rotation, but it's a lot easier to nudge a 3 inch knob 1 degree vs nudging a 0.25 inch knob 1 degree.

Unfortunately when the subject comes up most people turn to reduction drives which have the dinkiest knobs of all!!! (It has to be small or it would cover up the Vernier dial).

Tim N3QE

-----Original Message-----
From: HBR [mailto:hbr-bounces at mailman.qth.net] On Behalf Of Stan McIntosh
Sent: Monday, August 18, 2014 9:02 AM
To: HBR Receiver List
Subject: [HBR] off-topic reminds me of on-topic questions

The balanced inductor antenna tuner reminds me of some on-topic thoughts that I have been thinking.  Reduction drives are still available, but they can be pricey and hard to find.  However, I have lately been playing with stepper motors, and I am thinking of trying to adapt (at least) one to VFO use.  If you'll search the term 28BYJ-48, you'll find a motor where you can get 5 motors with driver boards for $15 after shipping, and these pair nicely with a $5 Arduino board and a $2 bluetooth adapter.  These motors may only move in steps, but we're talking about over 4000 steps/revolution (the internal motor is 64 steps/revolution with a 63.something:1 reduction drive in the case).  The reason I mentioned bluetooth is that I'm often lazy with the Arduinos; rather than put controls on the case, I'll just send setting information back and forth from my phone.

Sorry if this is blasphemous by munging solid-state with HBR, but I have been thinking about this as a way to make fine tuning easier.

Regards,
Stan
kd4bth
______________________________________________________________
HBR mailing list
Home: http://mailman.qth.net/mailman/listinfo/hbr
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:HBR at mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

From bcarling at cfl.rr.com  Mon Aug 18 10:32:24 2014
From: bcarling at cfl.rr.com (Brian Carling)
Date: Mon, 18 Aug 2014 10:32:24 -0400
Subject: [HBR] off-topic reminds me of on-topic questions
In-Reply-To: <303A17BD5F8FA34DA45EEC245271AC0BB7344ABA@JGEX2K10MBX2.wmata.local>
References: <CAKVLtWPxr_7cUrvXb0uJ+u3wtpJGVZGdJuZ9cyiDOC9gqqabaQ@mail.gmail.com>
	<303A17BD5F8FA34DA45EEC245271AC0BB7344ABA@JGEX2K10MBX2.wmata.local>
Message-ID: <DA3A3444-F527-4069-B90F-6A946C2D2CEB@cfl.rr.com>

Actually Tim the National Velvet Verniers have a huge knob.

Best regards - Bry Carling



> On Aug 18, 2014, at 9:52 AM, "Shoppa, Tim" <tshoppa at wmata.com> wrote:
> 
> You would be surprised, how much it helps with fine tuning to replace a dinky little knob with a reasonable or big-sized knob.
> 
> Yes, it's still the same Hz per degree of rotation, but it's a lot easier to nudge a 3 inch knob 1 degree vs nudging a 0.25 inch knob 1 degree.
> 
> Unfortunately when the subject comes up most people turn to reduction drives which have the dinkiest knobs of all!!! (It has to be small or it would cover up the Vernier dial).
> 
> Tim N3QE
> 
> -----Original Message-----
> From: HBR [mailto:hbr-bounces at mailman.qth.net] On Behalf Of Stan McIntosh
> Sent: Monday, August 18, 2014 9:02 AM
> To: HBR Receiver List
> Subject: [HBR] off-topic reminds me of on-topic questions
> 
> The balanced inductor antenna tuner reminds me of some on-topic thoughts that I have been thinking.  Reduction drives are still available, but they can be pricey and hard to find.  However, I have lately been playing with stepper motors, and I am thinking of trying to adapt (at least) one to VFO use.  If you'll search the term 28BYJ-48, you'll find a motor where you can get 5 motors with driver boards for $15 after shipping, and these pair nicely with a $5 Arduino board and a $2 bluetooth adapter.  These motors may only move in steps, but we're talking about over 4000 steps/revolution (the internal motor is 64 steps/revolution with a 63.something:1 reduction drive in the case).  The reason I mentioned bluetooth is that I'm often lazy with the Arduinos; rather than put controls on the case, I'll just send setting information back and forth from my phone.
> 
> Sorry if this is blasphemous by munging solid-state with HBR, but I have been thinking about this as a way to make fine tuning easier.
> 
> Regards,
> Stan
> kd4bth
> ______________________________________________________________
> HBR mailing list
> Home: http://mailman.qth.net/mailman/listinfo/hbr
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:HBR at mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> ______________________________________________________________
> HBR mailing list
> Home: http://mailman.qth.net/mailman/listinfo/hbr
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:HBR at mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html

From wrcromwell at gmail.com  Mon Aug 18 10:50:56 2014
From: wrcromwell at gmail.com (Bill Cromwell)
Date: Mon, 18 Aug 2014 10:50:56 -0400
Subject: [HBR] off-topic reminds me of on-topic questions
In-Reply-To: <DA3A3444-F527-4069-B90F-6A946C2D2CEB@cfl.rr.com>
References: <CAKVLtWPxr_7cUrvXb0uJ+u3wtpJGVZGdJuZ9cyiDOC9gqqabaQ@mail.gmail.com>	<303A17BD5F8FA34DA45EEC245271AC0BB7344ABA@JGEX2K10MBX2.wmata.local>
	<DA3A3444-F527-4069-B90F-6A946C2D2CEB@cfl.rr.com>
Message-ID: <53F212D0.4010400@gmail.com>

YES! They do!

73,

Bill  KU8H


On 08/18/2014 10:32 AM, Brian Carling wrote:
> Actually Tim the National Velvet Verniers have a huge knob.
>
> Best regards - Bry Carling
>
>
>


From bear57 at telus.net  Wed Aug 20 01:53:54 2014
From: bear57 at telus.net (Lorne Barber)
Date: Tue, 19 Aug 2014 22:53:54 -0700
Subject: [HBR] off topic. SP 600
Message-ID: <000001cfbc3b$20b292e0$6217b8a0$@net>

I realize this is not directly HBR related and for this I apologize. 

I am rebuilding a Hammarlund SP600 receiver.  I am doing modifications as
described by Doug Blakeslee and documented in the August 1970 issue of QST.

I am specifically having some issues with the "S" meter and the AVC
circuitry. I am hoping someone on this list has had some experience with
this old gem, possibly  having done the mods.

and may be able to offer some guidance. For this I would be grateful.

There may somewhere  be a Hammarlund list but so far I have not found it.

 

7 3 

Lorne

VE7BOX

 


From wrcromwell at gmail.com  Wed Aug 20 05:52:04 2014
From: wrcromwell at gmail.com (Bill Cromwell)
Date: Wed, 20 Aug 2014 05:52:04 -0400
Subject: [HBR] off topic. SP 600
In-Reply-To: <000001cfbc3b$20b292e0$6217b8a0$@net>
References: <000001cfbc3b$20b292e0$6217b8a0$@net>
Message-ID: <53F46FC4.3020101@gmail.com>

Hi Lorne,

Have a look here..on the same server as the HBR list:

http://mailman.qth.net/mailman/listinfo/hammarlund


I am on that list because I used to have a Hammarlund and I may yet again. Depends on what follows me home from a hamfest. Good luck to you with your project.

73,

Bill  KU8H


On 08/20/2014 01:53 AM, Lorne Barber wrote:
> I realize this is not directly HBR related and for this I apologize.
>
> I am rebuilding a Hammarlund SP600 receiver.  I am doing modifications as
> described by Doug Blakeslee and documented in the August 1970 issue of QST.
>
> I am specifically having some issues with the "S" meter and the AVC
> circuitry. I am hoping someone on this list has had some experience with
> this old gem, possibly  having done the mods.
>
> and may be able to offer some guidance. For this I would be grateful.
>
> There may somewhere  be a Hammarlund list but so far I have not found it.
>
>   
>
> 7 3
>
> Lorne
>
> VE7BOX
>
>   
>
> ______________________________________________________________
> HBR mailing list
> Home: http://mailman.qth.net/mailman/listinfo/hbr
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:HBR at mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
>


From hbr at mailman.qth.net  Wed Aug 20 13:39:10 2014
From: hbr at mailman.qth.net (Ejparagi--- via HBR)
Date: Wed, 20 Aug 2014 13:39:10 -0400 (EDT)
Subject: [HBR] off topic. SP 600
Message-ID: <468eb.7e47f34d.4126373e@aol.com>

Hello Lorne,
 
There is a web for the Western Historic Radio Museum that has some  
excellent rebuilding articles including one for the Hammarlund SP-600  with lots of 
excellent photos.  I have met Henry Rogers a few times and  have been 
impressed by his work.  He used to operate a radio museum in the  basement of his 
home in Virginia City, Nevada.  I think he has moved and  the museum may no 
longer be in operation but the website is still going.   It's worth a look 
and a read.  Caution: if you like vintage gear you will  spend a lot of time 
at his site!
 
There is also a 4 hour set of videos (DVD format) on rebuilding the  
SP-600JX available from the electric radio magazine book store.  I can  supply the 
address and particulars if you are interested.
 
73 and Good luck with your project,
Ed
WB9RMA
 
PS-  I have an SP-600JX that is on the list of rebuild projects in my  
shack.
 
 
 
 
 
 
In a message dated 8/20/2014 1:18:54 P.M. Eastern Daylight Time,  
bear57 at telus.net writes:

I  realize this is not directly HBR related and for this I apologize. 

I  am rebuilding a Hammarlund SP600 receiver.  I am doing modifications  as
described by Doug Blakeslee and documented in the August 1970 issue of  QST.

I am specifically having some issues with the "S" meter and the  AVC
circuitry. I am hoping someone on this list has had some experience  with
this old gem, possibly  having done the mods.

and may be  able to offer some guidance. For this I would be grateful.

There may  somewhere  be a Hammarlund list but so far I have not found  it.



7 3  

Lorne

VE7BOX



______________________________________________________________
HBR  mailing list
Home: http://mailman.qth.net/mailman/listinfo/hbr
Help:  http://mailman.qth.net/mmfaq.htm
Post:  mailto:HBR at mailman.qth.net

This list hosted by:  http://www.qsl.net
Please help support this email list:  http://www.qsl.net/donate.html


From bear57 at telus.net  Wed Aug 20 14:27:53 2014
From: bear57 at telus.net (Lorne Barber)
Date: Wed, 20 Aug 2014 11:27:53 -0700
Subject: [HBR] off topic. SP 600
In-Reply-To: <53F46FC4.3020101@gmail.com>
References: <000001cfbc3b$20b292e0$6217b8a0$@net> <53F46FC4.3020101@gmail.com>
Message-ID: <004601cfbca4$75435880$5fca0980$@net>

Thanks Bill, John and Ed. I have found the list and have joined.
Isn't this internet great, well most of the time anyway!
7 3 
Lorne
VE7BOX

-----Original Message-----
From: HBR [mailto:hbr-bounces at mailman.qth.net] On Behalf Of Bill Cromwell
Sent: August-20-14 2:52 AM
To: HBR Receiver List
Subject: Re: [HBR] off topic. SP 600

Hi Lorne,

Have a look here..on the same server as the HBR list:

http://mailman.qth.net/mailman/listinfo/hammarlund


I am on that list because I used to have a Hammarlund and I may yet again.
Depends on what follows me home from a hamfest. Good luck to you with your
project.

73,

Bill  KU8H


On 08/20/2014 01:53 AM, Lorne Barber wrote:
> I realize this is not directly HBR related and for this I apologize.
>
> I am rebuilding a Hammarlund SP600 receiver.  I am doing modifications 
> as described by Doug Blakeslee and documented in the August 1970 issue of
QST.
>
> I am specifically having some issues with the "S" meter and the AVC 
> circuitry. I am hoping someone on this list has had some experience 
> with this old gem, possibly  having done the mods.
>
> and may be able to offer some guidance. For this I would be grateful.
>
> There may somewhere  be a Hammarlund list but so far I have not found it.
>
>   
>
> 7 3
>
> Lorne
>
> VE7BOX
>
>   
>
> ______________________________________________________________
> HBR mailing list
> Home: http://mailman.qth.net/mailman/listinfo/hbr
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:HBR at mailman.qth.net
>
> This list hosted by: http://www.qsl.net Please help support this email 
> list: http://www.qsl.net/donate.html
>

______________________________________________________________
HBR mailing list
Home: http://mailman.qth.net/mailman/listinfo/hbr
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:HBR at mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html


From rrfowler0429 at att.net  Sun Aug 24 16:51:20 2014
From: rrfowler0429 at att.net (Ralph Fowler)
Date: Sun, 24 Aug 2014 15:51:20 -0500
Subject: [HBR] FS - Eddystone 898 dial
Message-ID: <E912C96A-2F57-4130-A213-AC0E379E2F20@att.net>

Never used. No template. In excellent condition.

$150 plus shipping. Email for pictures.


From rrfowler0429 at att.net  Sun Aug 24 17:01:21 2014
From: rrfowler0429 at att.net (Ralph Fowler)
Date: Sun, 24 Aug 2014 16:01:21 -0500
Subject: [HBR] FS - Eddystone 898 Dial
In-Reply-To: <53F2272C.3060107@cox.net>
References: <fzD21o00X45oxQM01zD4hL> <53F2272C.3060107@cox.net>
Message-ID: <DCA57B13-3910-4A5E-B1F3-8642FBC27C5E@att.net>

Never used and in pristine condition.

$150 plus shipping.

Sent from Ralph's Ipad

From hbr at mailman.qth.net  Mon Aug 25 09:39:42 2014
From: hbr at mailman.qth.net (Michael Rieff via HBR)
Date: Mon, 25 Aug 2014 09:39:42 -0400 (EDT)
Subject: [HBR] FS - Eddystone 898 Dial
In-Reply-To: <DCA57B13-3910-4A5E-B1F3-8642FBC27C5E@att.net>
References: <fzD21o00X45oxQM01zD4hL> <53F2272C.3060107@cox.net>
	<DCA57B13-3910-4A5E-B1F3-8642FBC27C5E@att.net>
Message-ID: <8D18E8129288F5A-105C-26618@webmail-va053.sysops.aol.com>

Ralph,


I'm interested.  Please contact me directly at Mike.Rieff at gmail.com if the unit is still for sale.  Thanks,


Mike



-----Original Message-----
From: Ralph Fowler <rrfowler0429 at att.net>
To: hbr <hbr at mailman.qth.net>
Sent: Sun, Aug 24, 2014 4:01 pm
Subject: [HBR] FS - Eddystone 898 Dial


Never used and in pristine condition.

$150 plus shipping.

Sent from Ralph's Ipad
______________________________________________________________
HBR mailing list
Home: http://mailman.qth.net/mailman/listinfo/hbr
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:HBR at mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

 

From rrfowler0429 at att.net  Thu Aug 28 17:45:46 2014
From: rrfowler0429 at att.net (Ralph Fowler)
Date: Thu, 28 Aug 2014 16:45:46 -0500
Subject: [HBR] Eddystone 898 dial
Message-ID: <D8F2E239-21BF-4392-B218-41B2E723248D@att.net>

Sold.


