[Hammarlund] SP-600-JX14
Joe Connor
joeconnor53 at yahoo.com
Sat Aug 22 11:16:02 EDT 2020
The are BB caps on the turret modules. Hammarlund had a
special wrench for getting them out. Its a PITA to do without the
tool but can be done.
The modules are held in by spring clips. If you're not very, very careful, those clips can go shooting off and travel remarkable distances. They also have a habit of landing in the damnedest places. I think the BBs are only in the modules for the lower two bands.
Joe Connor
On Friday, August 21, 2020, 10:54:40 PM EDT, Richard Knoppow <1oldlens1 at ix.netcom.com> wrote:
This is the switch I mentioned. If someone was careless in
removing or replacing the bottom cover to the turret its possible
it got cracked. The wafer can be repaired with super glue or
epoxy (I prefer expoxy).
If this receiver has not been rebuilt, as many were by the
military, it will be filled with "Black Beauty" caps. Sprague had
some sort of production problem with these and they began to fail
not long after being made. If your receiver has them the all need
to be replaced. In the 1950s when the receivers were rebuilt and
in later Hammarlund production, they were replaced with disc
ceramic caps but now its better to use plastic film type caps
which are more stable than ceramic. Not expensive. There are some
forty caps. Most are easy to get to but a couple, the ones in the
IF can on the side of the turret box, and the ones in the crystal
oscillator box take some work. The bathtub caps are electrolytics
and should also be replaced. I would not restuff them just used
modern electrolytics mounted on terminal strips.
The BB caps, sometimes called Bumble Bees because of the
color coded stripes on them, are paper and would be questionable
by now even if there had not been a problem. One trouble is that
the 600V versions are oil filled and the oil leaked out of the
end seal which is also the outer foil terminal. This is actually
the filling tube and if soldered at too high a temperature the
seal is broken. A lot of these caps are cracked or even have
pieces broken off. In any case they should all be replaced.
Most of the silver-mica caps are OK and should not be
shotgunned but some can go bad and cause some odd problems.
The are BB caps on the turret modules. Hammarlund had a
special wrench for getting them out. Its a PITA to do without the
tool but can be done.
There were also some special tools for the turret but it
hardly ever needs service.
Also, take the top off the turret compartment and inspect the
tuning cap for bent plates on the oscillator section. They should
be straight. Some people thought that the plates should be bent
to adjust the calibration, NEVER do this.
It is possible, however, for the stators to get out of
alignment with the rotors. This is not difficult to fix but
requires removing the tuning cap from the housing. Probably does
not need to be touched but have a look at it.
IMO these are exceptionally good receivers but have a bad
reputation because many of them are badly misaligned or plain
broken. They are not difficult to work on despite being heavy.
The quality will repay the effort. There is lots of information
available via the web and many who are very knowledgeable about
them and will give you help.
I also think they are among the sexiest looking receivers.
On 8/21/2020 7:27 PM, Joe Connor via Hammarlund wrote:
> What Les said. If that cap shorts, it can take out the filter chokes.
> Joe Connor
> On Friday, August 21, 2020, 08:21:59 PM EDT, Les Locklear <leslocklear at hotmail.com> wrote:
>
> Al is right, That switch is exposed and can accumulate lots of crud. Also a cap next to it is either a bumblebee or grey lady of death cap.
>
> That's the first thing I'd do.
>
> Les
>
>
> ----- Original Message -----
> From: Al Parker <anchor at ec.rr.com>
> Reply-To: <anchor at ec.rr.com>
> To: Brian Harris <cosmophone at yahoo.com>, Hammarlund <hammarlund at mailman.qth.net>
> Sent: 8/21/2020 4:16:45 PM
> Subject: Re: [Hammarlund] SP-600-JX14
> ________________________________________________________________________________
>
> (I have tried to send this at 3:20 PM, but the TWC/Spectrum email server
> is off line apparently. I'll try later)
>
> Hi Brian,
> You do not need to remove the turret to do any 'normal' service work on
> the SP-600.
> Take a look at <http://www.hammarlund.info/SP600svc.html> for an
> article be Ray Vasek, W2EC, several yrs ago and has given me permission
> to have it on the Hammarlund Historian website. You may find j;ust what
> you want in there.
> The electrical power switching from single to double conversion is done
> by the small single pole wafer switch that is located on the back of the
> turret box, under the chassis. Maybe there's a simple solution right there.
> If you have any questions once you get into it, I'll be glad to try to
> help.
> 73,
>
>
> Al, W8UT
> www.boatanchors.org
> www.hammarlund.info
>
> "There is nothing -- absolutely nothing -- half so much
> worth doing as simply messing about in boats"
> Ratty, to Mole
> On 8/21/2020 2:42 PM, Brian Harris via Hammarlund wrote:
>> I have the aforementioned receiver. It works on the single conversion bands (<7.4 MHZ) and but on the double conversion bands it doesn't. I know there are problems with the 3.5 MHz oscillator and second mixer. Is there an easy way to get to the components under the associated RF chassis? It looks like removal of the bandswitch turrent at minimum is required and that appears to be a formidable task. Any comments appreciated.. Thank you.
>>
>> Brian Harris, WA5UEK cell 214-763-5977 email cosmophone at yahoo.com
>> ______________________________________________________________
>> Hammarlund mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/hammarlund
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:Hammarlund at mailman.qth.net
>>
>> List Administrator: Gary Harmon, K5JWK
>> ** For Assistance: gharmon at idworld.net **
>>
>>
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
>>
> ______________________________________________________________
> Hammarlund mailing list
> Home: http://mailman.qth.net/mailman/listinfo/hammarlund
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Hammarlund at mailman.qth.net
>
> List Administrator: Gary Harmon, K5JWK
> ** For Assistance: gharmon at idworld.net **
>
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> ______________________________________________________________
> Hammarlund mailing list
> Home: http://mailman.qth.net/mailman/listinfo/hammarlund
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Hammarlund at mailman.qth.net
>
> List Administrator: Gary Harmon, K5JWK
> ** For Assistance: gharmon at idworld.net **
>
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
>
> ______________________________________________________________
> Hammarlund mailing list
> Home: http://mailman.qth.net/mailman/listinfo/hammarlund
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Hammarlund at mailman.qth.net
>
> List Administrator: Gary Harmon, K5JWK
> ** For Assistance: gharmon at idworld.net **
>
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
--
Richard Knoppow
1oldlens1 at ix.netcom.com
WB6KBL
______________________________________________________________
Hammarlund mailing list
Home: http://mailman.qth.net/mailman/listinfo/hammarlund
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Hammarlund at mailman.qth.net
List Administrator: Gary Harmon, K5JWK
** For Assistance: gharmon at idworld.net **
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
More information about the Hammarlund
mailing list