[Hallicrafters] Alumunum wiring

[Roger (K8RI)]

>The reason you have to tighten the screws in your breaker panel and the 
>reason that aluminum wiring in houses caused

I haven't had to tighten them, just check them for proper tightness.  When 
the panel was put in those screws were really tightened down, which of 
course did deform the 0000. I no longer check them every year which requires 
pulling the meter for safety and Consumers gets really upset if you are the 
one pulling the meter. Normally the guy will just walk up and pull the meter 
and leave even though you have a  5 minute job. At any rate I've never found 
them loose or even at reduced  tension and our voltages remain fairly 
constant at 115 to 118.

In the "old days" even running several hundred watts out on AM would result 
in lights dimming or getting brighter, depending on what circuit I had the 
station plugged into. We eventually found that old farm house had a floating 
neutral out at the pole.  The power company had neglected to hook it up.  It 
may be coincidence, but after it was hooked up we never had damage from a 
lightning strike again. Prior to that it was quite common.

I've always said that if the lights don't dim when you key the transmitter, 
then you are running QRP, but that house was an exception.


73

Roger (K8RI)


>fires was not because aluminum has more resistance and creates heat.  The 
>greater resistance of aluminum is compensated for when it is installed by 
>using 2 AWG larger wires which have the same resistance as the specified 
>copper wire size.  The cause of the fires was due to a property of metals 
>called creep.  Over a period of time when pressure is applied to an 
>aluminum wire the metal will slowly creep away from the point of pressure. 
>Copper has a very very low propensity to creep.

>Due to the installation methods used in the 60's, creep caused the 
>connections at outlet boxes and switches to become

I thought it was the junction boxes where the wires are simply spliced 
together by twisting on a "wire nut" which is really hazardous with 
aluminum. That same installation method is used today.

>loose creating a high resistance connection and heat.  The heat accelerated 
>creep which increased the resistance creating more heat.  The problem was 
>solved with the installation of a copper pigtail between the end of the 
>aluminum wire and the outlet or switch.  Builders were supposed to retrofit 
>houses with these pigtails.

----------------------------------------

From: "Roger (K8RI)" <Hallicraftersgroup at rogerhalstead.com>
Sent: Monday, September 10, 2007 2:46 AM
To: "Bob Young" <youngbob53 at msn.com>, <hallicrafters at mailman.qth.net>
Subject: Re: [Hallicrafters] Alumunum wiring

According to the instructions, I'm supposed to retighten/torque the large
allen screws that hold the 4 ought aluminum, in my main breaker panel once a
year.

Roger (K8RI)

>
> The reason Aluminum started so many fires is that it is not as good of a
> conductor as copper and has more resistance so it creates more heat. It
> used to expand and contract a lot with use and gradually loosen up the
> screw terminals in the outlets and other places creating a bad contact.
> This bad contact used to heat up and some of them started fires.
> Oh and yes I love the glow of tubes.
>
> Bob KB1OKL
>>
>> >
>> > Regarding the price of copper...
>> >
>> > In the wind power industry (and probably elsewhere as
>> > well) I have seen a shift toward aluminum cables
>> > instead of copper cables...I've also seen transformers
>> > wound with aluminum rather than copper. Wonder how
>> > long before aluminum wire becomes the standard?
>> >
>> > WB6FQL
>>
>>Never unless you want to relive the late 60's when it was used in many
>>homes; usually cheap tract style. Created a bit of a ruckus with fire
>>departments. Banned by NEC shortly after that.
>>
>>Carl
>>KM1H
>>
>>
>>
>> >
>>
>>
>>
>>------------------------------
>>
>>______________________________________________________________
>>Hallicrafters mailing list
>>Home: http://mailman.qth.net/mailman/listinfo/hallicrafters
>>Help: http://mailman.qth.net/mmfaq.html
>>Post: mailto:Hallicrafters at mailman.qth.net
>>
>>
>>End of Hallicrafters Digest, Vol 44, Issue 14
>>*********************************************
>
>
> ______________________________________________________________
> Hallicrafters mailing list
> Home: http://mailman.qth.net/mailman/listinfo/hallicrafters
> Help: http://mailman.qth.net/mmfaq.html
> Post: mailto:Hallicrafters at mailman.qth.net
> ----
> List Administrator: Duane Fischer, W8DBF **for assistance**
> dfischer at usol.com
> ----
> Hallicrafters Collectors International: http://www.w9wze.org

______________________________________________________________
Hallicrafters mailing list
Home: http://mailman.qth.net/mailman/listinfo/hallicrafters
Help: http://mailman.qth.net/mmfaq.html
Post: mailto:Hallicrafters at mailman.qth.net
----
List Administrator: Duane Fischer, W8DBF **for assistance**
dfischer at usol.com
----
Hallicrafters Collectors International: http://www.w9wze.org