Thanks Jeff. They both used to work 100% in sync a few years ago. This is something that has changed in the last few years.

One thing I’ll do is put the character generator on a scope (in series with a voltage source) to see what exactly is the difference between setting two characters of R and Y vs. dot cycle.

As you suggested, I just tried the dot cycle on the ASR only (removing the KSR) and still had the same result RYYRYY.

I should also mention that, the rhythm of the machine sounds “off” almost like it is running faster than 45 baud. Not much faster, but just sounds off. It used to be when I ran both machines together, they audibly would be perfect. Now the ASR sounds like it is running a little faster. That is the only thing I can think of to describe the sound.

73 Eugene W2HX
My Youtube Channel: https://www.youtube.com/@w2hx/videos

From: Jeffrey Golas <[email protected]>
Sent: Sunday, June 2, 2024 9:56 PM
To: W2HX <[email protected]>
Cc: Greenkeys <[email protected]>
Subject: Re: [GreenKeys] M28 ASR Print Issue

Id compare selector magnet resistance/inductance, the repeating letters aImost seem like a signal issue than mechanical. Id also try an RY paper tape by itself (or try your tester on just that machine).

I wonder if one is intended for a different current rating or has any resistors on the loop that are aging or just too large.

Jeff

On Jun 2, 2024, at 9:37 PM, W2HX <[email protected]> wrote:

Hi all,

For the last several years, I’ve noticed that my ASR does not print traffic the same as my KSR both are on the same loop. I would say the accuracy of the print is much worse than the KSR. But since I had the KSR working well, I never had the impetus to look into in detail. Tonight, I did a simple test and saw some interesting results.

First, I am using a character generator which seems to work well (see attached picture). The character generator has several modes, QBF (sentence) is one mode, then you can set up two individual characters and send an alternating series of these characters. It also has a “dot cycle” mode, which I believe is simply alternating mark and space.

When I set up R and Y and send them out, both printers work perfectly. However, when I use the DOT CYCLE mode, the KSR again works FB, but the ASR shows RYYRYYRYY. Below are links to the print copy. Note there are two “paragraphs” on the page. The top paragraph is using the individual R and Y characters set up using toggle switches. The second paragraph shows the results of the DOT CYCLE mode. Again, these are on the same current loop.

KSR page: https://w2hx.com/x/What-Is-It/ASR-Printing-Issue/20240602_191335.jpg

ASR page: https://w2hx.com/x/What-Is-It/ASR-Printing-Issue/20240602_191352.jpg

Anyone have any suggestions where to look?

Thanks

73 Eugene W2HX
My Youtube Channel: https://www.youtube.com/@w2hx/videos

<20240602_191208.jpg>

______________________________________________________________
GreenKeys mailing list
Home: http://mailman.qth.net/mailman/listinfo/greenkeys
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]

Jordan Spencer Cunningham's GreenKeys Search Tool: https://teletype.net/gksearch

2002-to-present greenkeys archive: http://mailman.qth.net/pipermail/greenkeys/

1998-to-2001 greenkeys archive: http://mailman.qth.net/archive/greenkeys/greenkeys.html

Randy Guttery's 2001-to-2009 GreenKeys Search Tool: http://comcents.com/tty/greenkeyssearch.html

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [email protected]