Thanks all, makes sense. I am using deramps adapters, and I am fairly certain that if I can remove the deep layer of gunk/oxides/whatever that formed over many decades of shed storage on these contacts that were open, it will work great on the low voltage circuit.

I say that because the start bit contact works beautifully. It is the other 5 contacts that were left open to the air (were mechanically open when stored badly) that I am having trouble with.

I bet a good shot of high voltage would help, I have a high voltage supply out in the shed I may bring in. I expected the contact cleaner to chemically remove the problematic materials when combined with my mechanical cleaning, but apparently not.

-Eric




On Sun, Aug 6, 2023 at 8:33 AM Paul Heller <paul0926@comcast.net> wrote:
It was around 2009:



Paul
W2TTY

ITTY: HTTP://INTERNET-TTY.NET:8000/ITTY

On Aug 6, 2023, at 7:31 AM, Paul Heller <paul0926@comcast.net> wrote:

I remember a discussion years ago where a number of folks said high voltage was important for the contacts. The design voltage was much higher than 15v. You might try a loop source that delivers higher voltage and 60ma. That might work better with your contacts. 


On Aug 6, 2023, at 7:27 AM, Jeffrey Golas <jeffg@junknet.net> wrote:


Dont use sandpaper! The MA is important as it does affect the waveforms. The machine wants to see 60ma whether it's 120vdc or 15vdc. Set the scope to be wide enough to get an entire character if you havent already, it almost looks like the pic may just be showing the stop bit (33ms?).

Dial in the loop first, verify its 60ma at idle.

Jeff

On Aug 6, 2023, at 9:05 AM, Eric Moore <mooreericnyc@gmail.com> wrote:


https://deramp.com/downloads/teletype/Model%2015/loop%20interface%20board/Schematic%20Rev%20A.pdf

Verified the printer loop at 60ma. The keyboard loop runs at 15V, not sure on the ma, but not sure it matters much as it just opens and closes without driving any coils or similar.

I am fairly certain my issue is the contacts somehow. I see voltage (and continuity) up to those contacts, but despite cleaning fairly extensively with contact cleaner, they are still too high resistance. I am going to try some sandpaper today and see what is what...

-Eric

On Sun, Aug 6, 2023, 12:10 AM Gerry Block <gblock@sbcglobal.net> wrote:
typo:  "60 ma"

Sent from my iPhone

On Aug 5, 2023, at 10:07 PM, Gerry Block <gblock@sbcglobal.net> wrote:

eric

what does your loop schematic look like?  sketch it out and enclose photo. 
what is the loop power supply voltage. 
what is the series resistance to make the 60ms. 
are you sure it is running at 60 ms?
where is the scope probe grounded and where is the loop supply grounded?
i doubt it is the contacts.  

gerry

Sent from my iPhone

On Aug 5, 2023, at 5:49 PM, Eric Moore <mooreericnyc@gmail.com> wrote:


I have cleaned with contact cleaner and paper tape pretty extensively, but can always go another round.

I do not think that is a good waveform, but similarly, no idea.

-Eric

On Sat, Aug 5, 2023, 7:23 PM Jeffrey Golas <jeffg@junknet.net> wrote:
Correct me if Im wrong but could just be "dirty"; as the cam rubs against the switch youre seeing noise like a dirty volume pot.

Id use some alcohol and a business card and scrub the contacts (plus Im not sure thats even a terrible signal for a 1940s device. Going machine to machine I dont think that tiny bit of leakage woulda mattered.

Again, correct if wrong, Im here learning too.

Jeff KC3GJX

______________________________________________________________
GreenKeys mailing list
Home: http://mailman.qth.net/mailman/listinfo/greenkeys
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:GreenKeys@mailman.qth.net

Jordan Spencer Cunningham's GreenKeys Search Tool: https://teletype.net/gksearch
2002-to-present greenkeys archive: http://mailman.qth.net/pipermail/greenkeys/
1998-to-2001 greenkeys archive: http://mailman.qth.net/archive/greenkeys/greenkeys.html
Randy Guttery's 2001-to-2009 GreenKeys Search Tool: http://comcents.com/tty/greenkeyssearch.html

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to gblock@sbcglobal.net
______________________________________________________________
GreenKeys mailing list
Home: http://mailman.qth.net/mailman/listinfo/greenkeys
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:GreenKeys@mailman.qth.net

Jordan Spencer Cunningham's GreenKeys Search Tool: https://teletype.net/gksearch
2002-to-present greenkeys archive: http://mailman.qth.net/pipermail/greenkeys/
1998-to-2001 greenkeys archive: http://mailman.qth.net/archive/greenkeys/greenkeys.html
Randy Guttery's 2001-to-2009 GreenKeys Search Tool: http://comcents.com/tty/greenkeyssearch.html

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to phearvada@gmail.com