[GreenKeys] UPDATE- shockingly basic question - Teletype Model 33 ASR
Michael Katzmann
vk2bea at gmail.com
Wed Feb 24 19:53:09 EST 2021
Congrats ... A great feeling when it all comes together. In the past month
I've had to recap the electros in my spectrum analyzer and replace a
tantalum in both that and a receiver. When tantalums go bad they frequently
do so by shorting, as in these cases.
At least those you had to replace were pretty standard electros. The three
terminal one in the reader external supply might be hard to find!
Michael
On Wed, Feb 24, 2021 at 7:32 PM Andy KN4UCL <kn4ucl at gmail.com> wrote:
> UPDATE: The deal clincher per Wayne was the two caps (the 250 and 1500MFD)
> - inaugural powering up recorded for posterity.
>
> https://www.youtube.com/watch?v=gdO3BGXMGhM
>
> So far so good!
>
> cheers.... Andy
>
> On Wed, Feb 10, 2021 at 2:40 PM WAYNE <teletypeparts at comcast.net> wrote:
>
>> Andy,
>>
>> The trouble is the smaller electrolytic capacitor in the front of the
>> UCC-6. Just in front of the large green multi-tap resistor. 250 MFD at
>> 75VDC. Very common trouble.
>>
>> I have a couple used ones but you might want to order a new one from
>> Mouser. I think I would get 2 so you would have another for the second
>> 33.
>>
>> Also the 1500 MF at 30VDC electrolytic that lays behind the SMD card will
>> cause a buzzing when you push the armature open with power plugged in and
>> 33 in OFF position.
>>
>> But loud buzzing when power plugged in is definitely the smaller cap.
>>
>> 73,
>>
>> Wayne
>>
>>
>>
>> On 02/09/2021 8:47 PM Andy KN4UCL <kn4ucl at gmail.com> wrote:
>>
>>
>> I removed the SMD card and took a photo (see attached) and all looks
>> visually OK. Before swapping with the other one I popped it back in just
>> to make sure things were as before... but yikes! Quite a buzzing sound in
>> Line or Local. Line was no longer working and Local would not type very
>> faithfully. Buzzing did not stop so I quickly powered off, and when I did
>> there was a gentle mechanical 'pop' as the power released. I removed and
>> repositioned the card ... but same symptoms.
>>
>> Thought I'd better power off before something starts burning!
>>
>> On Tue, Feb 9, 2021 at 7:21 PM Michael Katzmann < vk2bea at gmail.com>
>> wrote:
>>
>> Try swapping the selector magnet driver card between the two units. (
>> vertical card on the right hand edge). If you are having problems in local
>> then it is not the RS232-current loop circuit but it might be the magnet
>> driver.
>>
>> On Tue, Feb 9, 2021 at 4:53 PM Andy KN4UCL < kn4ucl at gmail.com> wrote:
>>
>> So RIGHT NOW the machine is running great, just like in the video from
>> 1:42s onwards. It also prints perfectly in Local mode as well right now,
>> no matter how fast I try to type.
>>
>> However - it will intermittently go back to garbage output, as is shown
>> prior to 1:42s in the video.
>>
>> When I was testing in Local last night it was OK typing slowly, but
>> typing a little fast caused garbage output.
>>
>> So I think the terminal is intermittently behaving badly, in LIne and
>> Local.
>>
>> But.. of course... right now it is behaving itself!
>>
>> cheers
>> Andy
>>
>>
>>
>> On Tue, Feb 9, 2021 at 2:21 PM Michael Katzmann < vk2bea at gmail.com>
>> wrote:
>>
>> I don't see this as a parity issue. I would expect the ASR33 typing unit
>> to ignore parity on receive. Although, I think the tape punch will punch
>> the eighth bit (or parity) if received.
>> Likewise the tape reader will read and send all eight bits.
>>
>> Does the ASR read a tape and print consistently in local ?
>> I'd be suspicious of the RS232 converter. If you have an oscilloscope and
>> can look at the RS232 input compared with the current loop output it may
>> prove or dispel this hypothesis.
>>
>> Michael
>>
>> On Tue, Feb 9, 2021 at 1:22 PM Andy KN4UCL < kn4ucl at gmail.com> wrote:
>>
>> Well I was hoping that it was either my serial loop adapter acting up, or
>> a cabling-from-serial-converter-to-terminal-server problem. I've replaced
>> everything (including the terminal server) but sadly no obvious fix.
>>
>> https://www.youtube.com/watch?v=h-w-HCXI25E
>>
>> I've got two similar 33s (both no parity keyboards) and I've had them
>> both running at the same time connected to my terminal server for a while
>> now. Recently I get very garbled data on one of them. It doesn't seem to
>> be related to the connected equipment or cabling as I've replaced
>> everything.
>>
>> Then... very weirdly it starts working again, as you can see at 1:42s on
>> the video.
>>
>> Apart from fiddling about with the rangefinder, any other thoughts about
>> (simple 😁) tests or adjustments I can make to diagnose this?
>>
>> thanks folks.
>> Andy
>>
>> On Thu, Feb 4, 2021 at 3:33 PM Andy KN4UCL < kn4ucl at gmail.com> wrote:
>>
>> OK well this is all very embarrassing. I have two almost identical 33s
>> (both non-parity) .... the other one works great connected to my Terminal
>> Server so thought I'd better swap the RS232 Adapters, port and cable.. and
>> hey presto - my "not working due to parity errors" Teletype started running
>> fine!
>>
>> I then swapped back to the original RS232 adapter, cables and port...
>> expecting things to NOT work... but of course, everything ran fine (sigh.)
>>
>> I've tried jiggling the cables (I was hopeful maybe a weird cable problem
>> could be the issue) but I am struggling to see how a wiring problem would
>> look like a legit parity problem.
>>
>> Anyway! All good for now.. but I am curious what would cause these
>> parity-like symptoms. I am going to replace the cables anyway, and probably
>> grab another RS232 converter just in case.
>>
>> cheers!
>> Andy
>>
>> On Wed, Feb 3, 2021 at 11:05 PM Mike Douglas < deramp5113 at yahoo.com>
>> wrote:
>>
>> Since you are concerned about the parity of your keyboard while testing
>> the TTY printing function, I assume your terminal server is in a mode where
>> it echos characters that you type on the TTY keyboard back out to the TTY
>> printer and you are testing your printer by typing on the TTY keyboard?
>>
>> If this is what you’re doing and you have a non-parity keyboard, then set
>> the serial port to 7 data bits plus mark parity (non parity keyboards set
>> the 8th bit to one). This should ensure the server accepts the typed
>> characters. If you type one character at a time with a short pause between
>> each character, then each character should echo properly to the TTY
>> printer. The pause between each character will be more than the two stop
>> bits the printer requires (and the printer ignores the 8th bit).
>>
>> If, however, you have a telnet session open and are sending data from a
>> remote device to the TTY printer and are not using the TTY keyboard to
>> generate test data, then set the serial port to 8 data bits plus mark
>> parity. This will appear as 8 data bits and 2 stop bits to the printer (as
>> it requires) and the printer can then keep up with a steady stream of data.
>>
>> If you are getting some garbage characters with either of these methods
>> but everything prints correctly in local mode, you made need to adjust the
>> rangefinder a bit.
>>
>> Mike
>>
>> On Feb 3, 2021, at 9:22 PM, Andy KN4UCL < kn4ucl at gmail.com> wrote:
>>
>> My Teletype has a Deramp converter which goes direct into an Equinox
>> ELS-16 terminal server. When I start I get a session with the terminal
>> server and can interact directly with the server ... or telnet onwards
>> elsewhere.
>>
>> On Feb 3, 2021, at 10:00 PM, Mike Douglas < deramp5113 at yahoo.com> wrote:
>>
>> I guess I’m confused as to your test setup then. What is sending data to
>> your Teletype? Is it coming from an external source other than the
>> Teletype, or are you testing by somehow looping keyboard input from your
>> TTY back out to the TTY printer?
>>
>> Mike
>>
>> On Feb 3, 2021, at 8:36 PM, Andy KN4UCL < kn4ucl at gmail.com> wrote:
>>
>> I think I am still missing a trick or two here...I tried every
>> combination of 8 and 7 even/odd/none/mark/space and I get no printing at
>> all with 8 bit, but moderately bad spelling errors with 7. See attachment
>> below... presumably this means I have the non-parity keyboard?
>>
>> thanks in advance for your thoughts!
>> Andy
>>
>> On Sun, Jan 31, 2021 at 8:18 PM Mike Douglas < deramp5113 at yahoo.com>
>> wrote:
>>
>> If you select 8 bit with mark parity on your terminal server, you’ll
>> probably get the 8N2 timing the Teletype requires (the mark parity bit
>> serves as the first stop bit).
>>
>> Mike
>>
>> On Jan 31, 2021, at 7:11 PM, Andy KN4UCL < kn4ucl at gmail.com> wrote:
>>
>> Thanks guys for the responses - a lot of great info for me to digest!
>>
>> My terminal server (Equinox ELS-16) allows me to define character size as
>> 7 or 8 bits, and to set parity as NONE, ODD, EVEN, MARK or SPACE.
>>
>> I don't seem to have the ability to specifically state the number of stop
>> bits, however.
>>
>>
>> Anyway.. I'm going to crack my Teletype open and confirm exactly what's
>> going on.
>> cheers!
>> Andy
>>
>> On Sun, Jan 31, 2021 at 5:43 PM Keith Lueck < kwlueck at swbell.net> wrote:
>>
>>
>> Jim & Wayne are spot-on, of course. I learned the hard way that you best
>> include the parity bit - even though the 33 doesn't give a whit about
>> parity...
>> My machine was occasionally producing errors when I was feeding it 7 N
>> 2. Wayne Durkee set me straight, and, viola, when I sent it 7 M 2,
>> everything was 100% ducky.
>>
>> On Sunday, January 31, 2021, 03:32:30 PM CST, Jim Haynes <
>> jhhaynes at earthlink.net> wrote:
>>
>>
>> All the 33s and 35s generate 11 unit code. 1 start bit, 7 data bits, one
>> bit which may be even parity or may be marking, and two stop bits.
>> That's
>> where 110 baud comes from. 100 wpm = 10 chars/sec and each char contains
>> 11 bits. The reason for two stop bits is the difficulty of making a
>> mechanical selector that is reliable at 100 wpm.
>>
>> ---
>>
>> "Ya can argue all ya wanna, but it's dif'rent than it was."
>> "No it ain't! No it ain't! But ya gotta know the territory."
>> Meredith Willson, The Music Man
>>
>> ______________________________________________________________
>> GreenKeys mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/greenkeys
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto: GreenKeys at mailman.qth.net
>>
>> >>> Jordan Spencer Cunningham's GreenKeys Search Tool:
>> https://teletype.net/gksearch
>> >>> 2002-to-present greenkeys archive:
>> http://mailman.qth.net/pipermail/greenkeys/
>> >>> 1998-to-2001 greenkeys archive:
>> http://mailman.qth.net/archive/greenkeys/greenkeys.html
>> >>> Randy Guttery's 2001-to-2009 GreenKeys Search Tool:
>> http://comcents.com/tty/greenkeyssearch.html
>>
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
>> Message delivered to kwlueck at swbell.net
>>
>> ______________________________________________________________
>> GreenKeys mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/greenkeys
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto: GreenKeys at mailman.qth.net
>>
>> Jordan Spencer Cunningham's GreenKeys Search Tool:
>> https://teletype.net/gksearch
>>
>> 2002-to-present greenkeys archive:
>> http://mailman.qth.net/pipermail/greenkeys/
>>
>> 1998-to-2001 greenkeys archive:
>> http://mailman.qth.net/archive/greenkeys/greenkeys.html
>>
>> Randy Guttery's 2001-to-2009 GreenKeys Search Tool:
>> http://comcents.com/tty/greenkeyssearch.html
>>
>>
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
>> Message delivered to deramp5113 at yahoo.com
>>
>> <non parity keyboard.png>
>>
>> ______________________________________________________________
>> GreenKeys mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/greenkeys
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto: GreenKeys at mailman.qth.net
>>
>> >>> Jordan Spencer Cunningham's GreenKeys Search Tool:
>> https://teletype.net/gksearch
>> >>> 2002-to-present greenkeys archive:
>> http://mailman.qth.net/pipermail/greenkeys/
>> >>> 1998-to-2001 greenkeys archive:
>> http://mailman.qth.net/archive/greenkeys/greenkeys.html
>> >>> Randy Guttery's 2001-to-2009 GreenKeys Search Tool:
>> http://comcents.com/tty/greenkeyssearch.html
>>
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
>> Message delivered to vk2bea at gmail.com
>>
>>
>>
>>
>>
>>
>> --
>> |\ _,,,---,,_ Michael Katzmann
>> /,`.-'`' -. ;-;;,_ NV3Z / VK2BEA / G4NYV
>> |,4- ) )-,_. ,\ ( `'-'
>> '---''(_/--' `-'\_) vk2bea at gmail.com
>>
>>
>>
>> ______________________________________________________________
>> GreenKeys mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/greenkeys
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:GreenKeys at mailman.qth.net
>>
>> >>> Jordan Spencer Cunningham's GreenKeys Search Tool:
>> https://teletype.net/gksearch
>> >>> 2002-to-present greenkeys archive:
>> http://mailman.qth.net/pipermail/greenkeys/
>> >>> 1998-to-2001 greenkeys archive:
>> http://mailman.qth.net/archive/greenkeys/greenkeys.html
>> >>> Randy Guttery's 2001-to-2009 GreenKeys Search Tool:
>> http://comcents.com/tty/greenkeyssearch.html
>>
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
>> Message delivered to teletypeparts at comcast.net
>>
>>
--
|\ _,,,---,,_ Michael Katzmann
/,`.-'`' -. ;-;;,_ NV3Z / VK2BEA / G4NYV
|,4- ) )-,_. ,\ ( `'-'
'---''(_/--' `-'\_) vk2bea at gmail.com
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://mailman.qth.net/pipermail/greenkeys/attachments/20210224/59c233d9/attachment.html>
More information about the GreenKeys
mailing list