[GreenKeys] Model 19 gears

[E.]

I don’t remember if you said that the ribbon advanced when you took the basket off or not.  If not… I got a basket from one of the kind folks here on greenkeys since both of mine were either for weather or finance ;p .  Anyways, what I ended up having to do was to disassemble both mechanisms that advance the ribbon.  They were totally gummed from either old oil, old ink or grime… probably all three.  Nothing took care of it while it was all together - mineral spirits, nothing.  If you have to go down that route, please be very careful because I ended up breaking off one of the… whatever they are called and had to use a spare off of another ;p .  A cloth, rubber mallet, vice grips, flat head screw driver, mineral spirits, more, etc… it took a good few hours to “pry” (not so much pry) all those parts out and clean them.  Very much good luck if that’s what your going to have to do in the end ;o ~


> On Jul 25, 2018, at 1:21 pm, Kevin H. Phillips <kh-phillips at 9-5usa.org> wrote:
> 
> I'm making progress.  I took the typing unit off again and worked the main shaft by hand.  The clutch "appeared" to be working but I applied liberal doses of oil to it and to the area underneath the magnets.  I also removed the cap at the end of the main shaft and dripped oil down the center.  I put the typing unit back on the machine, hooked everything up, called up ITTY, and let it start printing.  This time after a few lines it started copying mostly correctly.  The LF had not been working before and it began working as it should.  The typing basket had been advancing only about half-way down a line and now it is going to the proper end. CR & LF seem to be working as they should.  It is typing pretty well so it is obviously 60wpm.  The only "major" problem now is that the ribbon isn't advancing and returning so it just types until it pounds a hole in the ribbon.  I'm going to let it run open for awhile and see if that jars the mechanism loose.  I had put quite a lot of oil on the typing basket/head so it "should" be well lubricated.  There must be some residual guminess somewhere.
> 
> 
> Kevin
> 
> 
> On 7/25/2018 12:01 PM, Kevin H. Phillips wrote:
>> On 7/25/2018 8:24 AM, ken Schwieker wrote:
>>> When you push a key does the cam on the keyboard make one revolution?
>>> Ken S
>>> 
>> Yes, it does.  Hopefully I can work on this a little while this afternoon.  The keyboard clutch was slightly stuck so I used some of the penetrant oil to free that up so perhaps the clutch on the main shaft is also gummy.
>> 
>> Kevin
>> 
>> ---
>> This email has been checked for viruses by Avast antivirus software.
>> https://www.avast.com/antivirus
>> 
>> ______________________________________________________________
>> GreenKeys mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/greenkeys
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:GreenKeys at mailman.qth.net
>> 
>> 2002-to-present greenkeys archive: http://mailman.qth.net/pipermail/greenkeys/
>> 1998-to-2001 greenkeys archive: http://mailman.qth.net/archive/greenkeys/greenkeys.html
>> Randy Guttery's 2001-to-2009 GreenKeys Search Tool: http://comcents.com/tty/greenkeyssearch.html
>> 
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
> 
> ______________________________________________________________
> GreenKeys mailing list
> Home: http://mailman.qth.net/mailman/listinfo/greenkeys
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:GreenKeys at mailman.qth.net
> 
> 2002-to-present greenkeys archive: http://mailman.qth.net/pipermail/greenkeys/
> 1998-to-2001 greenkeys archive: http://mailman.qth.net/archive/greenkeys/greenkeys.html
> Randy Guttery's 2001-to-2009 GreenKeys Search Tool: http://comcents.com/tty/greenkeyssearch.html
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html