[ForSale-Swap] FS: C & L

[marv_e_ads at juno.com]

***** VACUUM CAPACITORS & other Vacuum things *****
 
Jennings Vacuum Variables -- all used (or at least aged) 
 
UCSL-750    750pF  3KV  $125  with standard puller  
UCSL-1000  1000pF  3KV  $125  with standard puller
 
CVCD-1000   1000pF  20KV    $200  with standard puller  (My Hipot only
goes to 15KV so that all I could test this one) 
 
R1G  SPST 20KV 20Amp Vacuum Switch; no solenoid  $25
 
Collins 622-0193-001 low profile motor drive assembly with limit switches
 for a Jennings CMV1-4000 vacuum cap.  $40
 
Jennings mounting flanges, used.  FM2 FM2B FM2S $25 ea


---Fixed vacuum caps--
 
Jennings VC-12 12pF 20KV $20
Jennings       50pF 86KV $86
 
Western Elec   50pF  5KV   $15  
 
--- Vacuum Relays --
 
Struthers Dunn Type 78CCA109 "Keying Relay" which consists of a vacuum 
relay mounted on top of a small (2"x3"x4") metal enclosure.  There is a
15 pin Jones connector on the side of the box.  I believe that there are
some auxiliary contacts in the box in addition to the vacuum relay.  
28VDC.  $15

 
***** Air Variable Capacitors *****
 
Cardwell XR-1000PS 1000pF About 4.5" x 4" x 3.5" overall including plate
travel. .025 air gap. Used, Good condition.  $20 ea.
 
Cardwell XR-1000HS (about 950pF max measured) These have slightly
contoured plates for improved tuning resolution at minimum C.  .025 air
gap.  About 4.5" x 4" x 3.5" overall including plate travel.  Used, Good
condition.  $20 ea.
 
Cardwell 30-900pF (measured) (XR-900PS? -- 4 fewer plates than the above
units)  .025 air gap.  About 4.5" x 4" x 3.5" overall including plate
travel and mounting ears. used, Good condition.  $20  
 
Hammarlund SM-50-X, 7.5-50pF, .064 air gap, Just under 2" x 2" x 2"
overall not including 1/4" shaft.  Good condition.  $10.  

Johnson T9-5 miniature vertical PC mount trimmers 1.9-15.7 pF, Silver
Plated machined plates -- NOS  2/$1
  
Johnson 154-1,  12-244pF,  .05" air gap, about 3" x 3" x 3" overall. 
Rear shaft has been cut flush with bushing and the rear mounting tab has
been shortened a mite.  Otherwise, excellent condition, $25.

Johnson 500E20  (modern equivalent 154-3), 500pF/2KV, looks like .05" air
gap, about 3" x 3" x 4.5" overall not including 1/4" shaft which is about
1-1/2" long.  Good condition except the rear mounting tab has been
removed and it looks like a couple of the plates arced at one time and
were subsequently filed down a mite.  $20.

National Type DX 500pF variable capacitor, approx. 3" X 3" x 3" overall
fairly good condition.  Last one, $10

Remler "scissors" variables.  Type 630  350pF  $25
                              Type 631  500pF  $25

4 Section capacitor 20-550 pF per section large receiving style
capacitor.  $25
 

**** Ceramic Doorknob & Disk caps ***
 
  These are used Centralab or similar -- $5 ea or 5/$20
 
   68pF   5KV   850 series   
 
  These are NOS disks by KD & Erie  $3ea or 4/$10
 
  1500pF 7.5KV
  .01uF    4KV
 
  NOS Silver Mica caps 
 
  2200 pF  500V  CM06 $1 ea
  5100 pF  500V  CM07 (high current rating)  $2 ea
 
*****  Roller Coil  ******
 
La Pointe L-0201 406-1 (identical to a Johnson 229-201) 10 uH. used good,
$30
 
New! GE Ceramic end plates, part no. 7463338, for a GE roller coil. I
believe these fit the GE coil that was used in the BC-375.   $10 pair

*****   B&W Air Dux coils  *****
 
These are NOS, 10" lengths, unless noted otherwise 
 
#1208T  1.5" dia,  8TPI, #16 wire, slight tarnish   $20
#1216T  1.5" dia,  16TPI, #20 wire, somewhat tarnished   $20
#1006T  1.25" dia,  6TPI, #14 wire, somewhat tarnished   $15
 
plus a NOS partial length
 
#1008T   1.25" dia, 8 TPI, #16 wire, 8" long -- $12
 
--- some other partial lengths
 
#2408T   3" dia, 8 TPI, #14 wire, 4" long shiny -- $15
#2410T   3" dia, 10 TPI, #14 wire, 2.5" slightly tarnished -- $10
 
#3030   2.5"" dia, 8 TPI, #14 wire, 4" tarnished -- $10
#3031   2.5"" dia, 10 TPI, #16 wire, 3" long somewhat tarnished -- $10
#3031   2.5"" dia, 10 TPI, #16 wire, 1.75" long somewhat tarnished -- $5
 
---a couple of Illumintronic Engineering parts
 
375 7367-P1 -- 1.5" dia.x  5.75" winding w/ indented turns, 14 TPI, #17,
7" overall including plastic center support, un-used somewhat tarnished  
$25
 
980-0121-000 --  2.5" dia. x 7.5" winding w/ indented turns, 8 TPI, #14,
9.5" overall including plastic center support, used somewhat tarnished
but, no
turns soldered   $30
 
A large RF choke -- #22 enameled wire space wound 24 TPI for 2.75 on a 1"
diameter grooved fiberglass form 5" overall -- $5
 
Miller 62A024 series (.173-.272uH I think!?) coils, 1/4" diameter wound
with a 5 turn coil.  Blue (carbonyl SF 40-300 MHz)  core.   4 terminals,
2 currently unused.  NOS.  2/$1
 
Toroidal Tank coil -- The core is fiberglass & resin encased.  It is
currently wound with 20 turns of #12 wire.   There are notches in the
form for up to 40 turns.  It is a bit over 4 inches in diameter and about
1-3/4" thick.  This was made by Bob, W6YUY.  See his article in August
1985 Ham Radio magazine "Design a Toroidal Tank Circuit for you Vacuum
Tube Amplifier".   $50
 

All of the above plus shipping, if necessary, naturally.
 
Contact:  Marv  WC6W   310 649 3111 (reasonable hours Pacific Time
please)  
or via:  Marv_E_Ads at Juno.com





*

________________________________________________________________
Juno Platinum $9.95. Juno SpeedBand $14.95.
Sign up for Juno Today at http://www.juno.com!
Look for special offers at Best Buy stores.